Question about 2001 Honda Accord

1 Answer

Fog lights How do i get the old bulb out?

Posted by on

  • pilotte Oct 07, 2008

    cant even get to the bulb. having trouble removing the casing.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 350 Answers

Depends which side it is n/s or o/s but the best way of doing them is to jack the car up and drop the lower front bumper cover just screws and plastic push in plugs this just makes it easy access to the rear of the lamps on the back of the lamps just turn the back cover off the back of the lamp half a turn should do it this is the awkward bit because they can be fiddlely but take your time it is a simple piece of spring wire that just needs pushing down and un hooking it can be a bit awkward if you have not done it before but not rocket science yates210456

Posted on Sep 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How hard is it to change a fog light bulb on a 2005 Subaru Forester? Can anyone do it?


Front Fog Light Assembly

REMOVAL


  1. Disconnect the ground cable from battery.
105919447



  1. Remove the two clips and lower mudguard on side that bulb is being changed.
  2. Disconnect the harness connector from bulb on back of fog lamp.
105919448




Front Fog Light Bulb

REMOVAL


1. Locate back cover on fog lamp assembly where bulb is located inside.

105919462



  1. Remove the back cover.
105919463



  1. Remove the spring retainer, and then detach the fog light bulb.
  2. DO NOT TOUCH HALOGEN BULB!! Oils from skin will cause bulb to explode during operation.

Jul 27, 2011 | Subaru Forester Cars & Trucks

1 Answer

How do you replace the fog light bulb on 2008 avalanche


    • 1 Open the hood and reach down into the engine bay for the fog light assembly. If you cannot reach the fog light assembly from the top you may need to get underneath the truck to reach it. Remove the electrical plug running to the fog light ballast.
    • 2 Remove the bulb. Unlock the fog light bulb by turning it counterclockwise and pulling it straight out of the assembly.
    • 3 Slide a new bulb into the fog light assembly. The part number you will need for the new bulb will be located on the ballast or base of the old bulb.
    • 4 Turn the bulb clockwise to lock it into the fog light housing.
    • 5 Reconnect the electrical connector to the bulb ballast.

Jan 23, 2011 | 2007 Chevrolet Avalanche LTZ

1 Answer

How do u change a bulb in the fog lights on a


The fog lights on most vehicles sit directly underneath the headlight bulbs. The ballast and wiring work just like the headlights, so changing them takes not much time. The procedure to change the fog light is as follows:-- 1) Open the hood and reach down underneath the headlights to unplug the electrical plug from the fog light assembly. Squeeze the top of the release tab and pull the connection off the bulb's ballast. 2)Turn the fog light counterclockwise to remove it from the fog light housing. 3)Install the new fog light bulb.Then connect electrical plugs properly. 4) Test the fog lights by turning it ON. Thanks. you can rate this solution and show your appreciation.

May 20, 2010 | 2003 Ford Focus

2 Answers

How do you change the headlight bulb on 1996 olds delta 88? I cannot get to the bulb assembly.



REMOVAL & INSTALLATION

See Figures 1, 2, 3 and 4
  1. Disconnect the negative battery cable.
  2. Remove the fog lamp-to-bumper assembly retaining screws. Be careful not to disturb the adjusting screw.



0900c152800b1fa2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Unfasten the 2 Torx® fog light retaining screws (1), making sure not to disturb the adjusting screw (2)
  1. Squeeze the bulb and socket assembly retaining clip prongs inward, and pull the bulb and socket from the rear of the fog lamp.



0900c152800b1fa3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Squeeze the bulb and socket retaining clip prongs inward ...


0900c152800b1fa4.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: ... then pull the bulb from the rear of the fog lamp
  1. Unplug the fog lamp electrical connector.



0900c152800b1fa5.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Unfasten the fog lamp electrical connector
  1. Install the assembly, retaining bolts and connect the negative battery cable.


AIMING

  1. Park the car on a level surface, at least 25 ft. (7.6m) from a wall that is perpendicular to the ground surface. Make sure there is no excess weight in the trunk, unless you normally travel with that amount of weight in the car. Bounce the car a few times to settle the suspension.
  2. Measure and record the distance from the ground to the center of each fog light lens.
  3. Turn the fog lights on and adjust so the hot-spots (lit area of most concentrated intensity) are 4 in. (10cm) below the height of the lenses. The ADJUSTING screw is located at the top right corner of the fog light.

Jan 25, 2010 | 1996 Oldsmobile 88

1 Answer

How do I replace the fog light assembly on a 2000 Olds Alero?


you replace the fog lamps by going under front bumper fascia.remove the pushpins and take down the splash shield to access the back of the fog lamps.then you remove two bolts retaining the fog lamp to the back of front bumper.besure to wear clean gloves.because fog lamps is halogen bulbs.if you touch with bare hands the oils from hands will make the bulbs over heat and blow out.

Dec 03, 2009 | 1999 Oldsmobile Alero

1 Answer

How to change fog lights bulbs on my 2005 honda


548ae69.gif
  1. Remove the fog light mounting screw.
  2. Disconnect the connector from the fog light.
  3. Turn the socket about 45° counterclockwise and remove it from the housing.
  4. Remove the bulb from the socket.
To Install:
  1. Install the bulb in the socket without touching the glass with bare hands.
  2. Turn the socket about 45° clockwise to install it.
  3. Connect the connector to the fog light.
  4. Install the fog light mounting screw.

Jul 14, 2009 | 2005 Honda Odyssey

1 Answer

Put new bulbs in fog lights, now fog lights wont come on. 98 cadi catera. replaced old bulbs with new halogen bulbs now neither fog light will come on


Halogen bulbs are brighter and generally draw more current than standard filament ones.
Have you check that the supply fuse has not popped ?

Jun 21, 2009 | 1998 Cadillac Catera

1 Answer

Bulb wont come out of fitting


Do you have a NEW bulb? The bulb assy 'twists' out (counterclockwise) and a new bulb 'twists' in (clockwise). Each bulb has a connector to it. Remove the connector, twist out the old bulb, twist in the new one, and reconnect the connector.25d2850.jpg

Apr 17, 2009 | 2003 Hyundai Tiburon

1 Answer

2001 Acura Cl Sport fog light bulb


The # should be on the the old bulb, or check in your owner's manual. countrycurt0

Sep 04, 2008 | 2001 Acura 3.2CL

2 Answers

Changing fog light bulb


I just replaced the fog light bulb on my 2008 Azera. I went under the car and removed two screws from the protective shield. I pulled down the shield and reached up and turned the fog light socket and pulled it out of the housing, remembering which side the wires were on and removed the old bulb (Don't touch the new bulb with your hand) and replaced it with the new bulb. The job took less then 15 minutes

Aug 08, 2008 | 2002 Hyundai Santa Fe

Not finding what you are looking for?
2001 Honda Accord Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...