Question about 1995 Chevrolet Lumina Apv

4 Answers

Passenger window went down will not go up

Window energized down but now neither switch will rais up....replaced both switched with used....no luck fuse ok....now what

Posted by on

  • mariontent Jun 23, 2008

    the motor was energized when the window went down..from either switch..is the motor now faulty..or too weak to raise back up? thanks.

×

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 426 Answers

The motor may be slipping may have died or simply came loose can you hear any sound when you try to roll the window back up?? if you ever think you have a bad switch dont replace it simply jump the wires to see if it resolves it if it does then the switch is bad if you still have the same issue your problems are else where, Check ALL cables and see if you can find any loose connections use a 12v testing tool to see if the wires are hot and if the current will flow when pushed then have a helping hand push button while you check to see if your motor is getting power. the testers are like 14 bucks at walmart and are sold in a car stero install kit looking thing, other wise just use a multi meter

Posted on Jun 23, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,487 Answers

Use a circuit tester to test the switches. You can test both switches from the right side door. Gently pry the plate holding the switch up and out of the door with a flat blade or screwdriver. There are several wires coming out of the switch. Five large gauge wires control the motor. The center wire is hot. Two of the other wires come from the left hand switch and the remaining two go to the motor. Find a good ground. Test each of the five wires. One wire is hot when pressing the UP button on either right or left door (Check both sides). One wire will show hot when pressing DOWN button on either door. These are the wires that go to the motor. If you have power here you will have to trace those wires to the motor.

Remove the door panel: Two screws inset in door handle. One screw under plastic cover on top front of door panel. Two screws on bottom of door panel. Remove cover around door latch handle. Pull the panel straight up.
Hope this helps........

Posted on Jun 23, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 19,396 Answers

The window is pushed up by a lever at the base of the glass if it is out of place the window may go down but not back up, if this is not the cause then the motor is faulty and does not produce anough strengt to push the glass up.

Posted on Jun 22, 2008

  • Ginko
    Ginko Jun 23, 2008

    If the motor is humming usually it is the support at the base of the glass or the belt. You need to remove the door panel to fix it.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 1,894 Answers

May be faulty power supply?

have u checked it?

Posted on Jun 22, 2008

  • 1 more comment 
  • dewan nafees ahmed Jun 22, 2008

    check the supply from the batteries to the motor which does the lifting work

  • dewan nafees ahmed Jun 22, 2008

    dont forget to accept MY solution if u go by it.

    feel free for asking any doubts u have.

    thank u for ur cooperation.

    good luck for getting fixed soon

  • dewan nafees ahmed Jun 23, 2008

    motor should be able to raise up again when it lfits.

    if not there is a problem with the motor.

    when it brings down its s deceleration motion. so no power is required.

    but to lift it up it needs work to be done

    and hence motor can be the problem


×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the power window relay located in a 2002 mercury villager?


Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Visual Inspection Chart Mechanical Electrical
  • Improperly aligned window
  • Damaged window mounting
  • Window frame interference
  • Central junction box (CJB) Fuses:
    • F30 (10A)
    • F32 (20A)
    • F34 (20A)
    • F59 (7.5A)
  • Battery junction box (BJB) Fuses:
    • F20 (30A)
    • F27 (45A)
  • Switches
  • Circuits
  • Connectors
  • Heated back light
  • Relays
Which window is not working ?
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .

Apr 07, 2015 | 2002 Mercury Villager

1 Answer

Passenger window switch works but the drivers side switch does not


was regulator bad? did it work from drivers side switch before you did regulator repair?..if so passenger side switch wiring has issue and is not sending signal through it back to the drivers side master switches.. otherwise you need to pin test for power up power down on drivers side switch and repair that if issue going to the window on passenger side.. (possible pinched at door jam area common)

Nov 20, 2013 | 2002 Hyundai Accent

1 Answer

The power window switch on the driver's door of my 2005 civic hybrid for the right rear passenger window only rolls the window down, not up (the switch on the passenger window door works fine). I'm having...


If your window rolled down than means your window regulator is getting power. It's most likely your switches are bad.

When you use the down switch it supplies power to your window regulator. When you use the up switch it supplies power also but the polarities are switch which causes the window to roll in the opposite direction.

Sounds like your up switch is not making a complete connection to make your window roll back up.

For parts, check this LINK.

Good luck.

Jun 02, 2010 | 2005 Honda Civic

1 Answer

Passenger side window won't roll up using the driver's side switc


Before you replace anything, inspect the connector pins in both the driver's door switch and the passenger door switch. If you don't find any problem with these connector pins, replace the driver's door control switch.

Aug 18, 2009 | 2003 Hyundai Tiburon

2 Answers

Passenger Window Stuck all the way Down


Try switching the power window switch from the passenger side to the drivers side. Before you do that try with the switch on the up position, wiggle it from side to side. The contacts may be worn and by wiggling it may make contact. Other then that try to park it in side or garbage bag taped to keep rain out till you get it to the shop.
Hint, take it to a Auto window repair shop to replace the switch if it's bad or if the motor is bad. They have more experience to removing the door panels and removing the power window regulator (motor) if that needs to be replaced.
Good luck and hope this helps. 

May 30, 2009 | 1999 Dodge Caravan

1 Answer

Passenger window problem on 05 taurus


I imagine u need a new switch, but it could be the motor shorted out too.. If the motor shorted it would normally blow a fuse so you ought to check that first. If the fuse is intact and the switch light is off, its probably the switch broken. Its doesnt take long to test the switch with a voltmeter/Ohmeter.

Jan 08, 2009 | 1999 Ford Taurus

3 Answers

2000 GMC Jimmy SLE driver's power window


The same thing happened to my 1999 JMC Jimmy recently. I believe the problem is that your power window motor has most likely gone out or is starting to go out. The motor will need replaced. They are pretty expensive new. I went to a junkyard and got one for around 15 dollars. When mine went bad, I had rolled my window down about three or four inches and it stuck there. I took my door panel off and tapped on the motor while holding up on the window switch and got it to go up after a few minutes. I am replacing my motor today, I'll leave an update here about the outcome when I finish the job. I hope this information helps you.

Sep 27, 2008 | 2000 GMC Jimmy

1 Answer

Passenger window will not rais


Remove the door panel and unplug the window lift motor. Connect a test light across the harness plug and try the switch in both directions. If it lights in both the motor is bad or the regulator is stuck. You can put an ammeter in line and apply power again. If the amperage is high,the regulator is probably stuck. Good Luck.

Aug 15, 2008 | 2002 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21984 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...