Question about 1992 Ford Explorer

1 Answer

Remove the electric mirror switch

How do I remove the electric mirror switch for 1992 explorer? Are there keepers that will release with a blade slipped under the edges?

Posted by on

  • Anonymous Mar 31, 2014

    TO REMOVE MIRROR FOR REPAIR F FENDER

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,010 Answers

Removal and Installation

Remove the front door speaker. For additional information, refer to Section 415-00.
Remove the speaker watershield.
Remove the 2 speaker standoffs.
If equipped, remove the window regulator handle.
Separate the handle cover from the handle.
Remove the screw.
Remove the window regulator handle.
Remove the spacer.

Remove the window control switch. For additional information, refer to Section 501-11.
Remove the bolt.
Remove the 2 front door lower bolts.
Remove the door handle cover plate.
Remove the 2 door handle screws.
Remove the front door handle.
Guide the door handle through the opening in the trim panel.
CAUTION: Do not pull directly outward on the front door trim panel, as damage may occur.

Remove the front door trim panel.
Lift upward to remove the front door trim panel.
To install, reverse the removal procedure.

Posted on Jun 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the ignition tumbler on a 1992 Explorer?


  1. 1 Open the hood. Disconnect the cable from the negative battery terminal. Peel back the insulator if equipped, and use the wrench to loosen the clamp nut on the negative cable.
  2. 2 Remove the covers on the steering column. Use the screwdriver to pull out the screws, and detach the knee bolster below the steering column. Pull out the screws and detach the lower cover to find the screw for the upper cover; then remove the upper cover in the same manner.
  3. 3 Remove the multifunction switch by pulling out its retaining screw and pushing on the release lever to detach the switch from the column.
  4. 4 Disconnect the ignition switch's electrical connector. Then detach the switch from the steering column by pressing on its clips to release the tabs.
  5. 5 Install the new ignition switch in the old one's place, making sure the locking tabs activate and the spring under the switch is in position on the column's locking rod. Connect the electrical connector.
  6. 6 Reconnect all other parts on the steering column in reverse order of removal. Replace the negative battery cable.
  7. 7 Insert your ignition key to test for proper operation in all three positions: "Lock," "Accessory" and "Start."

Jan 22, 2011 | 1992 Ford Explorer

2 Answers

How to replace driver side mirror on 1999 GMC Jimmy. Just need steps for removing old one and can take it from there. Thanks!


if there is a plastic cover directly behind the mirror on the inside of the car it should come off by gently prying it with a flat blade or screwdriver around the edge of it as most are held on by plastic clips.
Once it is removed it will expose the nuts or bolts that hold the mirror to the door but dont forget to remove the electric wire plug that leads to the mirror

Jun 09, 2010 | 1999 GMC Jimmy

1 Answer

2002 Mountaineer. How do you change the light bulb at the bottom of the driver side rear view mirror. Dan


SECTION 501-09: Rear View Mirrors 2002 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.

NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
ed6be7c.gif
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released.
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

Dec 26, 2009 | 2002 Mercury Mountaineer

1 Answer

Cant remove the rotor and retainer clip


You will need a large bearing retaining nut socket (1-in drive) about 2 7/16th in or 61/62mm (I got mine at NAPA with a 1/2 in to 1-in drive converter) BUT BEFORE loosening the nut there is a small keeper under the bottom edge the nut at the top (12-oclock) position of the nut. Use a magnet to retrac this and then loosen the large bearing nut. You sometimes have to slightly move the nut "a hair" left or right to remove this bearing keeper. Once the keeper is out the nut will easily come off. The rest is easy. Good Luck!

Nov 09, 2009 | 1994 Ford Explorer Limited

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

1 Answer

How do you get the front door panel off of a 2003 ford explorer xlt to replace the mirror


1. on the inside, remove the plastic trim that is directly inside of the left side rear view mirror.. should just snap off.
2. remove the lens from the reflector/courtesy lamp on the door.
3. pop the plastic trim holding the window switches ...pull up on the front edge (closet to hood) and tip it up until you can release the back edge of the switch plate.
4. unhook the wire connections from the switches... look for the lock tab release lever...they're color coded and only fit in one location so don' worry about where they go..
5. There are two small screws to remove...one below where the switches were, and the other behind the lens of the reflector on the door.
Once you get these out, lift straight up on the panel and it will unhook from the slots in the door.
6. unplug the courtesy light from it's spot in the door panel by twisting.
that should get you there!

May 05, 2009 | 2003 Ford Explorer

1 Answer

Mirror glass replacement on drivers side


i don't have aviator. here's explorer, should be the same.

You will see a small rectangle where the screwdriver goes in. You are pryingtowards glass. The retention is about a 3 inch rectangle that has a lip around it that snaps onto a rectangle on the mirror body.

SECTION 501-09: Rear View Mirrors 2002 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released. (and pull screwdriver towards glass)
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

Apr 18, 2009 | 2003 Lincoln Aviator

1 Answer

I want to replace the driver's side mirror and need to remove the inside door panel thanks


here is step by step instruction to remove your door panel. i am not sure if the picture are coming through so please forgive me on the images. please do not forget to rate and comment about your experience today wih fixya Front Door
  1. On vehicles without power windows, place a soft cloth under the window regulator handle and pull upwards on the cloth to release the snapring. Remove the regulator handle and plate.
89550p12.gif Using a taped prytool, carefully remove the bezel portion of the handle
89550p14.gif Remove the bezel by pulling towards the tip of the handle
89550p15.gif Remove any screw covers ...
89550p16.gif ... and extract any retaining screws from the door panel
  1. Remove the screw from the inside handle and slide the handle forward. Disconnect and remove the handle from the control link.
  2. On manual mirrors, remove the setting screw and knob. Tape the end of a thin flat-bladed tool and pry the retainer loose to remove the cover.
  3. If equipped with power windows, remove the power window switch from the and armrest.
  4. Remove the mounting screws and remove the armrest from the door panel. Remove the inside door handle bezel by pushing rearward.
89550p18.gif Carefully pry the edge of the door panel around the outer edges, then remove the door panel
89550p13.gif Once the door panel is removed, make sure to disconnect all wiring
  1. Remove the door courtesy light by pulling outward. Disconnect the electrical wiring.
  2. Remove the two screw caps and speaker cover(s). Remove six screws from the trim panel.
  3. Remove the door pocket from the panel.
  4. Tape the end of a thin bladed tool, then insert the tool between the door panel and door and pry the panel outward. Disconnect the electrical wiring after the panel is free and remove the panel from the vehicle.
To install:
  1. Connect the electrical wiring, if equipped, and install the trim panel onto the door.
  2. Secure the trim panel with the mounting screws, then install screw caps and speaker cover(s).
  3. Install the door pocket.
  4. Install the armrest and secure with the mounting screws. Install the power window switch as required.
  5. Install the door courtesy lamp. Install the inside handle bezel.
  6. Install the outside rear view mirror cover and retainer.
  7. Connect the inside handle to the control link. Install the handle, slide it rearward and install the screw.
  8. With the door window fully closed, install the window regulator and handle.

Apr 17, 2009 | 1993 Toyota Camry V6

1 Answer

99 explorer drivers side mirror vibrates


are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

  1. Remove the front door trim panel; refer to Section 501-05 .
  2. go to car-part.com for a used mirror. Page with * is cheapest seller.
  1. Remove the speaker.
    1. Remove the screws.
    1. Disconnect the electrical connector.
    1. Remove the speaker.
  1. Remove the outside rear view mirror (17682).
    1. Disconnect the power mirror wiring clips.
    1. Remove the outside rear view mirror nuts.
    1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).
------------------------------------------------------
f9d70e9.gif
----------------------------
SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released.
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.
4d9527f.gif

Apr 12, 2009 | 1999 Ford Explorer

1 Answer

Power window off track


Remove the door panel and the armrest. Then you will need to slip a thin flat blade screwdriver under the panel and gently pry up to release the plastic keepers that attach the door panel. Then you can remove the panel and gain access to the window regulator and track. Be gentle prying out the plastic keepers so you don't damage the panel. Some of the keepers may break, but you can get more from Ford or your local parts house. These are a very common piece. Good luck.

Mar 06, 2009 | 2005 Ford F-150

Not finding what you are looking for?
1992 Ford Explorer Logo

357 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...