Question about 1998 Mazda 626

1 Answer

Brake Problem My sons 1998 Mazda 626 has had new disc & brake pads fitted to the front of his car & rear disc machined & new pads. Still has Brake problems & is costing him a lot money and the problem is not being fixed. Problem : When the brake is applied he gets a shudder feeling all the time through the brake pedal. His hand brake is adjusted each time it is serviced but after 1 month it is at max position up when pulled on. I hope that you can answer my questions.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 68 Answers

Hi im dave
hope i can help
when you had the rear pads applied and the discs turned was there noticeable damage to the disc surface it sounds like your e brake cable is not adjusted properly or perhaps the braided wires inside the insulation are seperating along your brake cable causing the rear brakes to not be adjsting themselves properly. Every time the parking brake is applied the rear brakes are self adjusted if they arent being applied due to slack in or a broken cable you will not adjust your rear brakes. This would accont for the flutter in the brake pedal as hydraulic fluid is still circulating to compress the pads against the rotor but the pads arent reaching the rotor.

Posted on Jul 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi My 1993 Mazda 626 hand brake would not release the rear left hand side disc. I had the car towed to a brake specialist who cleaned and lubricated a little spring loaded lever which is meant to pull...


I check my prices with this web site www.automd.com click on estimate cost and enter information, I checked my area,(Tucson,AZ. $800) and for a shop that's a fair price.

May 22, 2011 | 1993 Mazda 626

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

How to change front disc brake pads on 2000 Mazda Bravo B2500


jack up car, remove the road wheels, at the rear of the caliper you will have 2 or 3 bolts holding the caliper onto the stub axle, remove the bolts and remove the caliper, remove the outer pad, leave the inner pad in place and use a "G" clamp to compress the brake piston until it has bottomed, if this is not done the new pads will not fit back over the rotor as the piston is too far out and the new pads are thicker than the old ones.
place the new pads in the caliper and fit over the rotor, replace the 2 or 3 bolts that hold the caliper in place, replace the road wheel, tighten the nuts and lower the car to the ground, pump the brake pedal to see if you have brakes, if you do have brakes take it for a test drive away from any traffic if possible

Jun 13, 2010 | 1988 Mazda B2600 Cab Plus

2 Answers

Car moves when handbrake applied,rear disc brakes.


The hand brake needs adjustment and more than likely the rear disc brakes are worn out. Replace the worn pads before adjusting the hand brake.

Nov 07, 2009 | 1999 Mazda 626

1 Answer

Am contemplating buying 96 Mazda 626 but ABS warning light is on.


yes, if they've been on there awhile. while the front pads take most of the abuse,people sometimes forget about the rear pads which are 1/2 the size of the front ones.

Sep 02, 2009 | 1996 Mazda 626

2 Answers

Telstar tx5 rear disc brake piston will not retracted


You take the bolt from behind the cylinder and then you should see a 4mm allen key head. turn it and push cylinder in. take the bleeder valve off to relieve any pressure also and while screwing with an allen key its important to know that it is leftr hand thread. :)

Jun 19, 2009 | 1994 Mazda 626

1 Answer

Back rear brakes metal to metal sound


I would not doubt that it is from aftermarket parts.

Use silicon grease on the caliper slides and use brake grease on all metal to metal contact parts when installing the new parts.

Also, grind away any rust where the pads sit on the caliper bracket before installing them.

May 18, 2009 | 1998 Mazda 626

2 Answers

How to change out front brake pads on a 2001 mazda 626?


remove 2 caliper bolts, remove old pads. put new pads in there place, before installing the caliper, be sure to squeeze the piston back in the caliper otherwise it will not fit back over the new pads. than replace the caliper and the 2 mounting bolts.

May 07, 2009 | 1995 Mazda 626

1 Answer

CHANGING REAR BRAKE PADS


the best thing you can do is go to an autoparts store and purchase a haynes repair manual for your car. cost about $18, but will show you everything you need to know, with pictures.

Nov 28, 2008 | 1998 Mazda 626

Not finding what you are looking for?
1998 Mazda 626 Logo

469 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...