Question about 1986 Toyota MR2

1 Answer

Driver size power windows want go up

Power window want go up

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Will be the switch have had to replace for a mate on his

Posted on Jun 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My power seats and only the power windows on right side quit working on my 2007 silverado classic lt1500 I replaced the circuit breakers already and it did not fix the problem


Does you truck have Memory Seats ? There are 2 options of power seat systems available in full size trucks. The first is 6 way driver and passenger power seats without memory. The second is an 8-way driver seat plus 4-way lumbar with memory, heat and optional cool function.
If you replaced the circuit breaker , did you check for B+ voltage at the switch ? If you have memory seats there is a control module that is in the mix.
For the power windows same thing here ,the BCM - body control module is involved .A factory Tech 2 scan tool is still the best tool to use ,checking data parameters .
The switch for the front passenger power window has 2 positions UP and DOWN, and it's position is a direct input into the PDS. Upon receiving a request for power window operation (switch activation), the PDS supplies voltage to the power window motor right front up or down circuit and grounds the opposite and the power window motor runs to drive the window UP or DOWN.
The front passenger power window can also be operated from the driver master control. The front passenger window switch on the driver master control has 2 positions UP and DOWN and it's position is a direct input into the DDS. Upon receiving a request for front passenger power window operation, the DDS transmits a GMLAN message indicating the changed switch position. When the PDS receives this message, the PDS supplies voltage to the power window motor right front up or down circuit and grounds the opposite and the power window motor runs to move the window UP or DOWN.
GMLAN - is a data bus communication network that vehicle modules talk together on.
Rear Passenger Power Window Operation (RPO A31/AN3/DL3)
The body control module (BCM) monitors the window UP/DOWN command from the DDS. When the rear window UP or DOWN command is received, the BCM sends a signal to the appropriate rear window switch. The rear window switches continuously monitor the up and down signal circuits, if no function is being commanded, the signal voltage is at approximately B+ voltage. If the UP or DOWN function is commanded, the BCM signal voltage drops approximately 5 volts and the appropriate rear window switch will then command the window in the UP or DOWN direction.
Your best bet would be to take your truck to a GM dealer !
Your best bet

If

Nov 04, 2015 | Cars & Trucks

1 Answer

Power windows don't work


I can provide wiring diagrams and locations however I need to know what size motor you have. The 2.0L or 2.5L.

Thanks in advance

Jul 04, 2008 | 1989 Toyota Camry

1 Answer

This is the fuse panel cover for a 1999 1500 Chevy Silverado which fuse controls the driver side window switch


The picture is too dark. Usually the power windows, all of them, are protected by a 25 or 30 amp circuit breaker. It is usually found in the instrument panel fuse block, under the dash on the driver's side. The circuit breaker is a matchbook size "fuse", usually silver colored. A circuit breaker automatically resets if it gets tripped by like a short.

If you pull off the master switch, the driver's side switch, you should have one hot wire with key on. The power wire and the ground for the windows are both in the driver's master switch. This is where you begin testing the power windows if none are working. Check for a hot wire, and check the ground wire- use a multi-meter.

Jul 19, 2015 | Cars & Trucks

1 Answer

Power windows stopped working in my 01 Denali


ON THE DRIVER SIDE BELOW the window is a child safety lock for the other windows unlock it

Aug 06, 2014 | Cars & Trucks

1 Answer

Power window fuse size and where to put them


Your owner's manual should tell you where the fuses are and the size. If you no longer have the owner's manual this may help. There is a fuse panel on both sides of the dash if you open the front driver and passenger door's. Pull the cover off of each one of these, on the inside of the lid is a diagram of what each individual fuse is for, the ones for the power windows should be listed including what size fuse to replace the original with. There are also two other fuse boxes under the hood but these pertain more to the fuel and emissions systems along with the ignition and starting systems. I would think the power window fuses are in the panels located on the sides of the dash.

Feb 20, 2011 | 2002 Chevrolet Impala

1 Answer

Power Windows quit working on 2004 Mercury Mountaineer. Checked one fuse, and it is good. Manual shows 30 A Circuit Breaker, but not sure how to check, or if that could be problem.


fuses this size are usually under the hood on the drivers side fenderwell , black square box, possibly a hand type screw holding the cap on, not really a way to test these fuses other than to find one of a similar size in the fuse panel of a known working circuit and swap it with the power window fuse temporarily to see if they work

Jan 14, 2011 | 2004 Mercury Mountaineer

1 Answer

Power window motor


THERE WILL BE 2 10mm NUTS THAT HOLD THE GLASS TO THE REGULATOR, REMOVE THOSE. THE REGULATOR IS HELD ON BY THE WINDOW MOTOR, THERE IS 4 RIVETS HOLDING THE MOTOR GRID THOSE RIVETS AND THE MOTOR AND REGULATOR WILL COME OUT. REPLACE MOTOR AND REGULATOR INSTALL 4 RIVETS SIZE 1/4" DIA GRIP RANG 032" AND ATTACH WINDOW WITH NUTS TO REGULATOR.

Nov 05, 2009 | 1996 Pontiac Sunfire

1 Answer

Rear driver side power window regulator doesn't work


its normally a 10mm nut use a wrench size 10 to turn it anti clockwise

Dec 02, 2008 | 1996 Jeep Cherokee Country

Not finding what you are looking for?
1986 Toyota MR2 Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...