Question about 1998 Chevrolet Cavalier

1 Answer

Codes P0440 and P0300

2.2, 5spd. chuggs and misses, broke the exhaust hangers. OBD II says P0440 EVAP system fails to hold sufficient vacuum. P0300 - engine misfire detected by PCM. The EVAP System won't communicate with OBD II tests. I'm thinking the canister vent solenoid is bad, not sure though. Any thoughts?

Posted by on

  • Anonymous Mar 15, 2014

    obd code p0300 sienna 2011 basic v-6 the AC is not getting cold there's no leaks full free on and compressors fine

  • Anonymous Mar 17, 2014

    dont seam to missfire but gas mi is bad

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,039 Answers

The evap can simply be the gaz cap the 300 check for a good spark you may need wire and plug be carefull for those coil they offent defect good luck pierre

Posted on Jun 23, 2008

1 Suggested Answer

  • 1 Answer

SOURCE: codes P0440 and P0300

I have a 2005 chevy suburban and it's getting a p0300 code. I replaced the plugs and wires and still have the same problem . It runs rough at idle in gear. What should I check?

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is code p0440


EVAP Emission Control System Malfunction.
A code P0440 could mean one or more of the following has happened:
The gas cap is not installed or working properly The purge solenoid has failed The canister is plugged and not working properly Possible Solutions With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back. Inspect the EVAP system for cuts/holes in tubes/hoses Inspect for damaged or disconnected hoses around the Evap purge solenoid Check and/or replace the sensor Check and/or replace the purge valve Have a professional use a smoke machine to detect leaks

Sep 29, 2011 | 1997 Oldsmobile Cutlass Supreme

1 Answer

PO440 code on a 1999 chev tahoe


P0440 - Evaporative Emission Control System Malfunction
This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Symptoms: You likely won't notice any drivability problems.

Causes: A code P0440 could mean one or more of the following has happened:
The gas cap is not installed or working properly
The purge solenoid has failed
The canister is plugged and not working properly

Possible Solutions: with a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
Inspect the EVAP system for cuts/holes in tubes/hoses
Inspect for damaged or disconnected hoses around the Evap purge solenoid
Check and/or replace the sensor
Check and/or replace the purge valve
Have a professional use a smoke machine to detect leaks

Check it and keep us updated.

Aug 13, 2011 | 1999 Chevrolet Tahoe

1 Answer

It is coming up with p440 code


P0440 - Evaporative Emission Control System Malfunction

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Symptoms: You likely won't notice any drivability problems.

Causes: A code P0440 could mean one or more of the following has happened:
* The gas cap is not installed or working properly
* The purge solenoid has failed
* The canister is plugged and not working properly

Possible Solutions: With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
* Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
* Inspect the EVAP system for cuts/holes in tubes/hoses
* Inspect for damaged or disconnected hoses around the Evap purge solenoid
* Check and/or replace the sensor
* Check and/or replace the purge valve
* Have a professional use a smoke machine to detect leaks

Other EVAP DTCs: P0440 - P0441 - P0442 - P0443 - P0446 - P0453 - P0455 - P0456

Keep us updated and remember to rate this answer..

Feb 01, 2011 | Chevrolet Venture Cars & Trucks

1 Answer

What p0440 mean in the cars


P0440 OBD-II - Evaporative Emission Control System Malfunction


What does that mean?
This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.



Symptoms:
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook You likely won't notice any drivability problems.



Causes:
A code P0440 could mean one or more of the following has happened:
  • The gas cap is not installed or working properly
  • The purge solenoid has failed
  • The canister is plugged and not working properly

Possible Solutions:With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
  • Inspect the EVAP system for cuts/holes in tubes/hoses
  • Inspect for damaged or disconnected hoses around the Evap purge solenoid
  • Check and/or replace the sensor
  • Check and/or replace the purge valve
  • Have a professional use a smoke machine to detect leaks

Hope helps (remember rated this).

Jul 05, 2010 | 1999 Chevrolet Blazer

3 Answers

Emission control malfuction p0440


Easier said then done without professional tools

However, I'll start you will some theory, then the shop manual procedures followed by some "common" problems

Theory:
Evaporative leak detection strategy is based on applying vacuum to EVAP system and monitoring vacuum decay. Powertrain Control Module (PCM) monitors vacuum level by means of fuel tank vacuum sensor input. At a predetermined time, EVAP purge solenoid and EVAP vent solenoid are turned on. This allows engine vacuum to draw a small vacuum on entire EVAP system. Whenever a sufficient vacuum level cannot be achieved, a large leak or faulty EVAP purge solenoid is indicated.

Conditions for setting this DTC are as follows:
No TP sensor, ODM, IAT sensor, or MAP sensor DTCs present.
Start-up ECT 40-86°F (4-30°C).
Start-up ECT not greater than 14°F (8°C) greater than start-up IAT.
Start-up IAT not greater than 4°F (2°C) of start-up ECT.
Fuel tank level is 15-85 percent.
BARO is greater than 75 kPa.
Vehicle has been driven at least 11 miles.
EVAP system is unable to achieve or maintain vacuum during diagnostic test.

Diagnostic Procedures
1.) Perform On-Board Diagnostic (OBD) system check.
After performing OBD system check, go to next step.

2.) Check if DTC P1665 or P1676 is also set. If any of DTCs is present, diagnose affected DTCs. If DTCs are not present, go to next step.

3.) Turn ignition off. Remove fuel filler cap. Turn ignition on. Using scan tool, observe fuel tank pressure. If fuel tank pressure is zero in. H2O, go to next step. If fuel tank pressure in not zero in. H2O, diagnose evaporative system.

4.) Replace fuel filler cap. Using scan tool, capture FAILURE RECORD data for DTC P0440 and clear DTC. Command EVAP vent solenoid on. Connect EVAP Pressure/Purge Diagnostic Station (J-41413) to EVAP service port. Pressurize EVAP system using diagnostic station. Monitor pressure on EVAP pressure gauge on diagnostic station. If pressure is 5 in. H2O, go to next step. If pressure is not 5 in. H2O, go to step 6.

5.) Maintain EVAP pressure at 5 in. H2O. Observe fuel tank pressure on scan tool. If fuel tank pressure reading on scan tool is 5 in. H2O, go to step 8. If reading is not 5 in. H2O, go to next step.

6.) Disconnect fuel tank vapor line and EVAP purge line from EVAP canister. Block canister fitting for fuel tank pressure line. Connect a hand-held vacuum pump to canister fitting for EVAP purge line. Ensure that EVAP vent solenoid is still commanded on. Apply vacuum to EVAP canister. If vacuum can be maintained at 5 in. Hg, go to step 11. If vacuum cannot be maintained at 5 in. Hg, go to step 10.

7.) Check for restriction in fuel tank vapor line or EVAP purge line. Repair as necessary. After repairs, go to step 16. If restriction is not found, diagnose EVAP system.

8.) Disconnect vacuum source line at EVAP purge solenoid and plug vacuum source fitting on solenoid. Using scan tool's output tests function, select and activate SYSTEM PERF. Pressurize EVAP system to 5 in H2O. Observe EVAP pressure gauge on diagnostic station while removing plug from EVAP purge solenoid vacuum source fitting. If EVAP pressure decreases to zero in. H2O within 15 seconds while system performance is activated, go to next step. If EVAP pressure does not decrease to zero in. H2O within 15 seconds, go to step 13.

9.) Install vacuum gauge on EVAP diagnostic station to vacuum source line. Start and operate engine to greater than 2000 RPM. Observe source vacuum level. If vacuum level is greater than -15 in. Hg, If vacuum level is not greater than -15 in. Hg, go to step 14.

10.) Check for disconnected or damaged vent hose. Check for damaged EVAP canister. Repair as necessary. After repairs, go to step 16. If no problems are found, go to next step.

11.) Check for faulty or missing fuel filler cap. Check for disconnected or leaking fuel tank vapor line. Check for disconnected or damaged EVAP purge line. If problem is found, repair as necessary. After repairs, go to step 16. If no problems are found, go to next step.

12.) Using scan tool, command EVAP vent solenoid on. Continuously attempt to pressurize the EVAP system by leaving the EVAP diagnostic station control knob in the pressurized position. Using the Ultrasonic Leak Detector (J-41416), locate and repair leak in EVAP system. After repairs, go to step 16.

13.) Replace EVAP purge solenoid. After replacing solenoid, go to step 16.

14.) Check for carbon release into the EVAP system. Repair as necessary. After repairs, go to step 16.

15.) Replace EVAP vent solenoid. After replacing solenoid, go to next step.

15.) Turn ignition on. Using scan tool, command EVAP vent solenoid on. Using EVAP diagnostic station, pressurize EVAP system to 15 in. H2O. Move rotary switch in diagnostic station to HOLD and observe EVAP pressure gauge. If EVAP pressure decreases to less than 10 in. Hg within 2 minutes, repeat step 3. If EVAP pressure does not decrease, system is okay.

Diagnostic Aids
Check for the following:
Cracked or punctured EVAP canister.
Damaged or disconnected source vacuum line, EVAP purge line, vent hose, for fuel tank vapor line.
Poor connection at PCM.
Inspect harness connectors for backed-out terminals, improper mating, broken lock, damaged terminals, or poor wire connection.
Check for intermittent in circuit.
Check for kinked, pinched or plugged vacuum lines to EVAP purge or fuel tank vapor line. Also check for restrictions.
Faulty or damaged evaporative canister.

Apr 28, 2010 | 1999 Buick Century

3 Answers

Check engine light came on, says its a evaporative emission system, code# P0440, what is that?


What does that mean?
This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Possible Causes:
A code P0440 could mean one or more of the following has happened:
  • The gas cap is not installed or working properly
  • The purge solenoid has failed
  • The canister is plugged and not working properly
Possible solutions:
With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
  • Inspect the EVAP system for cuts/holes in tubes/hoses
  • Inspect for damaged or disconnected hoses around the Evap purge solenoid
  • Check and/or replace the sensor
  • Check and/or replace the purge valve
  • Have a professional use a smoke machine to detect leaks
HTH,

Mike...

Dec 04, 2009 | 1996 Chevrolet Cavalier

1 Answer

Trouble code P0440


This indicates that a part of the EVAP control system is no longer functioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses.

A code P0440 could mean one or more of the following has happened:
· The gas cap is not installed or working properly
· The purge solenoid has failed
· The canister is plugged and not working properly
With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
  • Inspect the EVAP system for cuts/holes in tubes/hoses
  • Inspect for damaged or disconnected hoses around the Evap purge solenoid
  • Check and/or replace the sensor
  • Check and/or replace the purge valve
  • Have a professional use a smoke machine to detect leaks

Nov 15, 2009 | 2004 Dodge Ram 1500

1 Answer

I have a 2001 grand am se p0440 code comes up


This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.
Causes:
A code P0440 could mean one or more of the following has happened:
  • The gas cap is not installed or working properly
  • The purge solenoid has failed
  • The canister is plugged and not working properly

With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
  • Inspect the EVAP system for cuts/holes in tubes/hoses
  • Inspect for damaged or disconnected hoses around the Evap purge solenoid
  • Check and/or replace the sensor
  • Check and/or replace the purge valve
  • Have a professional use a smoke machine to detect leaks

Feb 20, 2009 | 2001 Pontiac Grand Am SE

2 Answers

Codes P0440 and P0300


Hi,

A quick Internet search on those codes pulled up the following info.
http://www.obd-codes.com/p0440
  • Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
  • Inspect the EVAP system for cuts/holes in tubes/hoses
  • Inspect for damaged or disconnected hoses around the Evap purge solenoid
  • Check and/or replace the sensor
  • Check and/or replace the purge valve
  • Have a professional use a smoke machine to detect leaks
http://www.obd-codes.com/p0300
  • Faulty spark plugs or wires
  • Faulty coil (pack)
  • Faulty oxygen sensor(s)
  • Faulty fuel injector(s)
  • Burned exhaust valve
  • Faulty catalytic converter(s)
  • Stuck/blocked EGR valve / passages
  • Faulty camshaft position sensor
  • Defective computer

Dec 12, 2008 | 1999 Chevrolet Cavalier

2 Answers

Obd code p0440 for check engine light on 2000 Toyota Corolla


p0440 code means that the evap system has a leak. This could be caused by a bad or improperly installed gas cap. Either that or the purge solenoid has failed or the canister is plugged and not working properly.

Nov 15, 2008 | 2001 Toyota Corolla

Not finding what you are looking for?
1998 Chevrolet Cavalier Logo

Related Topics:

871 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...