Question about 1987 Ford Econoline

1 Answer

Changing motor in ups box van

Does the engine have to be removed through the side door? It is a ford chassis.

Posted by on

  • rjandrews Jun 23, 2008

    Thanks, now I will need to find a manual to find the easiest way to accomplish the task. Maybe, I'll just junk it.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,010 Answers

Yes, it does.

Posted on Jun 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse box for the dash assembly [wipers,radio,etc] in a 1998 kayo e350 motor home


An E350 is probably a Ford Econoline Chassis. It's probably in any of the 4 places that all fuse boxes are: 1) under the dashboard near the driver side. 2) On either side of the dash board hidden by the closed door(open the door to see an access panel) 3) behind the glove box or 4) in the engine compartment. These things begin as a cab and a chassis so it has to be any where from the cab forward. The remainder is part of a separate system with the battery an exception. Good luck.

Aug 16, 2015 | Cars & Trucks

1 Answer

Need to change out driver side motormount


To replace motor mount on your vehicle. Park the vehicle in level position. chock the wheels and set the parking brake, put the transmission shifter in park and disconnect the battery positive cable. Motor mount is located between engine and chassis. Support your engine whit the jack using 3/4" piece of plywood and set it under the oil pan. Loosen the motor mount bolt and lift slightly jack upward about 1/2" and remove the motor mount bushing and replace it whit new one and reverse instalation of removal process.

Apr 18, 2014 | 1989 Ford Aerostar Cargo

2 Answers

Where is the fuel filter and pcv valve on a 1993 G20 van


Hi!!
PCV valve located under engine cover, top of engine, mounted in passenger side valve cover

Fuel filter is located Under vehicle, passenger side, below seating area, front of fuel tank, mounted on chassis DON'T FORGET TO RATE THIS POST!!

Aug 23, 2010 | 1993 Chevrolet G20

1 Answer

On a 2003 Ford E250 Econoline van with electric door locks...is it possible to disconnect the rear and side cargo doors from being electrically controlled so that only a key can open them? How would I do...


Hi! Yes its possible if manual you want it to be. Try this, If the cargo doors have separate fuse from the fuse box then just remove the fuse and it would work manually. If you wont find the door fuse then you should work on the door manually. Open the cargo door trimming and you will find a motor inside the door. The motor has a connector that leads to the lock. Remove the connector to cut the power supply to the motor and you'll be on manual now. Hope this helps and have a good one!

Apr 27, 2010 | Ford E-250 Cars & Trucks

1 Answer

Don't have a manual for my Ford Freestar and I need to replace the fuse for my electronic doors.The battery died in the van and once restarted the electronic locks work but not the remote or the consult to...


IN THE FUSE BOX IN THE ENGINE COMPARTMENT IT IS FUSE #60 AND IT IS A 30 AMP FUSE.
IT IS OFF CENTER TO THE LEFT AND THE 2ND MINI FUSE UP FROM THE BLOWER MOTOR RELAY.

Nov 30, 2009 | 2005 Ford Freestar

3 Answers

2003 ford van e350 rear air vent is not blowing


Try this article. I have the same problem and I think it is the vacuum motor that controls the door for changing from hot/cold in the rear heater box (located inside behind the L rear wheel)

https://www.fleet.ford.com/truckbbas/non-html/Q19.PDF

Jul 08, 2009 | 2002 Ford E350

1 Answer

Dash wiring on a Ford Chassis Motorhome


if it was a van it would, is this a class A motor home? if so and it is a Truck chassis then no the wiring is all doe by the coach company who built the unit.

Apr 10, 2009 | 1988 Ford F 250

1 Answer

Where is the fuel pump reset switch located on a 1995 ford e250 econoline van?


the switch is located under passenger side foot trim panel under glove box. open passenger side door and remove the plastic cover .

Jan 28, 2009 | 1995 Ford Econoline

1 Answer

Heating problem in a 1999 ford windstar


This noise is the blend door electric stepper motor, this motor controls the door inside the heating ducts that diverts air across the heater core to heat the van, either the bleen door is warped from heat and stuck, or the blend door motor is defective, in order to fix this the dash assembly must be pulled to gain access to the motor and the door.

Dec 02, 2008 | 1999 Ford Windstar

2 Answers

Changed the gear box on the ford transit van


did you reset the computer after replacing it?

remove the positive battery cable for 10 mins.....

Nov 15, 2008 | 2000 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...