Question about 2000 Volkswagen Passat 4Motion

1 Answer

Vw passat 2000 1.8t front wheel drive

Po411 secondary air injection system, incorrect flow

Posted by on

  • 4 more comments 
  • 911ward Mar 18, 2009

    we plugged a code reader into my car and this is what it read... does it explain the hard ideling as well??

    when i am at a stop light my car shakes as if some type of pump is having a hard time kicking on and off and it causes my rpm's to go up and down....makes the car kind of vibrate...

  • Anonymous Apr 22, 2009

    i have the exact same car and i had the exact same problem. took it to volkwerke and replaced the alternator, and now its good as new

  • Anonymous Mar 17, 2014

    how to correct secondary air injection flow

  • Anonymous Mar 19, 2014

    PO411 code

  • Anonymous Mar 22, 2014

    Sideways play in front right wheel

  • Anonymous Mar 28, 2014

    As i turned the know to increase the air flow, I noticed smoke. I removed the knob and an inch long silver plate fell off the half circle copper

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 883 Answers

Please rate me solved...thanks

DTC P0411/16795: SECONDARY AIR SYSTEM - INCORRECT FLOW DETECTED
Test Requirements
Ensure all fuses are okay, battery voltage is at least 11.5 volts, all electrical accessories are off, A/C is off.
Ensure engine is mechanically sound.
Test Procedure

NOTE
Secondary air system is activated by ECM and blows air into exhaust pipe
upstream of catalytic converter for 100 seconds during a cold start, 41-91°F (5-
33°C). Engine must be cold to perform following test procedure.

1. Ensure fuse and secondary fuse (secondary fuse is 40 amp and is located in fuse holder on top of battery)
are okay. Check hoses and components of Secondary Air Injection System, for damage, loose fit and
improper installation, check vacuum hoses for Secondary Air Injection System. Repair as necessary.
Erase DTC memory. Verify repair. If DTC does not reset, test is complete. Perform ECM relearn
procedure. See TEST DRIVE RELEARN PROCEDURE .
2. Remove engine cover. Disconnect pressure hose from Secondary Air Pump Motor (V101), by pressing
buttons on hose connector. See Fig. 33 . Using scan tool, check Secondary Air Pump Motor (V101) in
scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See OUTPUT
DIAGNOSTIC TEST MODE .
3. Secondary Air Pump Motor (V101) should run in intervals and air should exit pump at hose connection.
If Secondary Air Pump Motor (V101) is okay, go to step 7 . If motor runs and no air exits secondary air
pump motor, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE . If
secondary air pump motor does not run, go to next step.
4. Disconnect Secondary Air Pump Motor (V101) harness connector, install LED test light at secondary air
pump harness connector terminals. Turn ignition on. Using scan tool, activate Secondary Air Pump Motor
(V101) in scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See
OUTPUT DIAGNOSTIC TEST MODE . LED test light at Secondary Air Pump Motor (V101) harness
connector should flash. If LED test light at Secondary Air Pump Motor (V101) harness connector does
not flash, go to next step. If LED test light at Secondary Air Pump Motor (V101) harness connector
flashes, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test is
complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
5. Using DVOM check resistance of Secondary Air Pump Motor (V101) wiring. See appropriate WIRING
DIAGRAM under ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS. Resistance should
be a maximum of 1.5 ohms for each reading. Check wiring for short circuit to one another in Secondary
Air Pump Motor (N101) harness connector. Repair as necessary. Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure.
Secondary Air Pump Motor (N101) wiring is okay, go to next step.
6. Check Secondary Air Pump Relay (J299) and Secondary Air Pump Relay (J299) wiring. See DTC
P0418/16802: SECONDARY AIR PUMP RELAY (J299), MALFUNCTION . Repair or replace as
necessary. Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure. See
TEST DRIVE RELEARN PROCEDURE .
7. Disconnect vacuum hose from Secondary Air Injection Valve (N112) and disconnect pressure hose from
secondary air pump motor, press buttons on pressure hose connector to disconnect pressure hose. See Fig.
34 . Blow lightly into disconnected pressure hose, Combi-Valve should be closed. Connect hand vacuum
pump to disconnected vacuum hose and apply vacuum to Combi-Valve, Combi-Valve should open. If
Combi-Valve opens when vacuum is applied, Combi-Valve is okay. Go to next step. If Combi-Valve
does not open when vacuum is applied, replace faulty Combi-Valve. Erase DTC memory. Verify repair.
Test is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
8. Check Secondary Air Injection Valve (N112). See DTC P0412/16796: SECONDARY AIR
INJECTION VALVE (N112), ELECTRICAL CIRCUIT MALFUNCTION . Repair as necessary.
Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure.
NOTE: Do not use compressed air to check Combi-Valve.
2000 Volkswagen Passat GLS
2000 ENGINE PERFORMANCE Self-Diagnostics - 1.8L Turbo

Posted on Jun 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A4 code p0411


code po411 refers to secondary air injection (AIR) system--incorrect flow detected===causes --AIR pump--AIR valves --AIR hose/s

check AIR hose fitting are tight. Check /replace the valves or pump

Aug 14, 2014 | Cars & Trucks

1 Answer

How to clean secondary air injection incorrect upstream flow detected Code PO411


The valve may need to be replaced. Only air flows thru the components.

Jul 03, 2012 | 2008 Chevrolet TrailBlazer LT

2 Answers

What is scanner code PO411


code po411 secondary air injection system incorrect flow,possible causes , faulty air pump or faulty air pump vacuum valve or faulty check valve.

Apr 06, 2011 | 1999 Volkswagen Cabrio

1 Answer

I have a 2000 vw passat GLX V6 5 Speed with the error codes p1411 -p1423 how do i fix it


P1411 = Secondary air injection system, bank 2 - insufficient flow detected.
Probable cause: Intake leak, hose(s) blocked / leaking, secondary air system valve / solenoid.

P1423 = Secondary air injection system, bank 1 - insufficient flow detected.
Probable cause: Intake leak, hose(s) blocked / leaking, secondary air system valve / solenoid.


Mar 13, 2011 | 2000 Volkswagen Passat 4Motion

1 Answer

I have a 2001 VW Jetta 1.8T. The check engine light came up and the codes that came up were P0171 (System too lean, meaning there is too much oxygen in the exhaust). And P0411 (Secondary air injection...


problem is bad AIR FLOW sensor! I am replaced in my 1.8T PASSAT with tuning chip 6.pcs air flow sensors over 3 years !!!!! All VW cars have a air flow problem!!!!! And not only this!!

Nov 15, 2010 | 2002 Volkswagen Passat

1 Answer

2002 VW Passat GLS 1.8T throwing two codes: P0171 and P0411. No noticeable loss in performance. Can I fix this myself?


System Too Lean (Bank 1)

Basically this means that an oxygen sensor in bank 1 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 1 is the side of the engine that has cylinder #1.
Note: This DTC is very similar to P0174, and in fact your vehicle may show both codes at the same time.

P0411 Secondary Air Injection System Incorrect Flow Detected, check the...Combination valve
...Secondary Air Injection pump motor
...Secondary Air Injection solenoid valve
I would take it to a mechanic

Apr 16, 2010 | 2002 Volkswagen Passat

2 Answers

Engine warning light came on. Diagnostic


P0411-Secondary Air Injection Incorrect Upstream Flow Detected. Could be the vacuum hose, combi-valve, and/or the pump http://www.passatworld.com/forums/showthread.php?t=170246. Read that thread and see if you think you or maybe somebody you know can tackle the problem.

Feb 09, 2010 | 2004 Volkswagen Passat

1 Answer

Service light came on, connected a scanner and got


There won't be - the secondary air injection system is strictly for cold-start emissions. You won't see any effects in driving, but if you have any sort of emissions check in your state's inspection, you will fail.

Nov 19, 2009 | 2001 Audi TT

2 Answers

Lincoln 1996 what does po411 means what the problem


Secondary AIR System Incorrect Upstream Flow Detected

Possible cause:
Electric air injection pump hoses leaking
Air pump blocked
AIR bypass solenoid leaking or blocked
AIR bypass solenoid stuck open or stuck closed

Mar 04, 2009 | 2001 Lincoln LS

Not finding what you are looking for?
2000 Volkswagen Passat 4Motion Logo

4,826 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...