Question about 1998 Ford Mustang

1 Answer

Recently owned 1998 ford mustang

I need to know, how the front bumper is installed, i think my new car have not any suport to hold down de front bumper, where can i get any picture or figure to see how install it?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 50 Answers

I always get a chiltons manual from any local auto part stores. its a book that shows step by step instuctions to do about anything to your car.

Posted on Jun 20, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the evaporative emissions charcoal canister located on 1998 v6 mustang

It should be at the rear of the car on drivers side in front of the bumper near the fuel tank.

Feb 24, 2012 | 1998 Ford Mustang

1 Answer

Well my battery of my mustang wint down and i had to chage the battery and my drivers window when it goes up it bouces bacj down to a 1/5 down and i want to know how to restore it.

NOTICE: Make sure no obstructions are present in the window system when carrying out this procedure.
NOTE: A battery disconnect does not require this procedure to be carried out unless the battery was disconnected while the window was operating.
NOTE: Excessive bounce-back (bounce-back that occurs with no obstructions present) may indicate a non-initialized window motor.
NOTE: Carry-out the de-initialization of the motor before initializing the motor.
NOTE: The motor will only operate in the 9-16 volt range. If the voltage drops below 9 volts, the window will not function correctly or may stop moving. If the voltage drops below 9 volts while the motor is operating, the motor will become de-initialized and will need to be initialized.
NOTE: The front window motors must be initialized whenever: a new window regulator and motor is installed, a new window glass is installed, a glass top run removal and installation or when carrying out any operation in which grease or lubricants are applied to the window system. A new front window motor is in a proportional up/down mode until initialized.
NOTE: The convertible rear window motors do NOT need to be initialized as they do not have one-touch up or one-touch down functions.
NOTE: All front window components (window glass, window regulator, window motor and glass top run) must be installed/tightened and adjusted to specification before carrying out this procedure.
NOTE: If this procedure is only partially completed, the front window motor remains non-initialized and only the proportional up/down functions operate. A non-initialized window motor may allow one-touch down operation, but does NOT allow one-touch up operation.

De-initialization then re-initialization

The motor can be de-initialized in 2 ways:

Disconnect the battery cable from the battery while the window is operating.

Remove the window motor fuse while the window is operating.

After the motor has been de-initialized, the initialization procedure must be carried out.

Make sure there are no obstructions present in the window system when carrying out this procedure. The door MUST be closed during this procedure (for convertibles, the top and quarter glass must be in the closed and up position), in order for the door window motor to initialize.

The windows must be in the full open position for this procedure to operate correctly.

Press and hold the window control switch in the UP position at the second detent until the window glass stalls into the glass top run for at least 2 seconds.

Once the top run is reached, hold the window control switch in the DOWN position at the second detent until the window glass stalls at the bottom of its travel for at least 2 seconds.

Cycle the window glass an additional 5 times to set the window soft stop for the down position.

Test for correct window operation by carrying one-touch up feature.

Good luck, if for any reason you can't give four thumbs up, please ask for more information. Thanks!

Apr 11, 2011 | 2005 Ford Mustang

1 Answer

Can a 2002 Ford Mustang have working headlights without a bumper being in place?

Yes, the headlamps are held in place with 2 push in retainers and are not part of the front bumper.

Feb 17, 2011 | 2002 Ford Mustang

1 Answer

1993 ford mustang brake pedal goes down on its own and brakes

Check the vacuum brake booster and check valve maybe there is a problem there that is amplifying the vacuum inside the booster and applying the brakes. I hope this helps, let me know.

Aug 02, 2010 | 1993 Ford Mustang

1 Answer

How do i install a front bumper on a 91 mustang? directions?

The best way to explain this is to recommend you get the Haynes repair manual on the vehicle.

Jul 04, 2010 | 1991 Ford Mustang

2 Answers

I got a mustang 1993 2.3 liter engine in it. Right under the air intake there is a little round black thing and it has a vacumm hose on it and another hose that runs to a black box under the front bumper...

I don't wanna lie about what i think it is, but u can always go to a ford dealer's parts dept and ge them to print you a diagram of that area. This will show you a list of the parts, and it is free! You may need them to print a couple diffrent times to get your part.

Dec 08, 2009 | 1993 Ford Mustang

1 Answer

Need to know where air bag sensor for 2000 mustang r located

they will be in the front and rear bumpers. anything that has anything to do with air bags have bright yellow or orange connectors. should be easy to find.

Aug 27, 2009 | 2000 Ford Mustang

1 Answer

Ford radio removal

You need two long pins ( real straight coat hangars may work) and insert them into the holes in the front of the radio and gently pull out.

Mar 18, 2009 | 1998 Ford Mustang

1 Answer

Wiring of fog lights on 95 Mustang

If you bought the fog lights from Ford and they plugged into factory plugs at the front bumper, then I suspect you need the headlight switch that came optional for your car. You will need to install a relay into the fuse box. Check for any fuses for that circuit. I did one on a Ford f-150 and the switch came with the lights from Ford.Usually the fog lights are not on until you push a button or turn the switch.

Mar 15, 2009 | 1995 Ford Mustang

Not finding what you are looking for?
1998 Ford Mustang Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5681 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides