Hello i am trying to fix my check engine light and the light is on and the code says its my egr valve is not getting enough flow and causing the light to come on. also dont know where the reset button for the check engine light is located on my 2001 toyota tacoma 4wd sr5

Hi Joe

Like all solenoid valves, you can clean them with throttle body cleaner and then test the solenoid electronically with a 12 volt supply.

P0401 Exhaust EGR Flow Insufficient

Toyota Nation Forum https://www.toyotanation.com > threads > p0401-exha...
May 1, 2014 - The sensor is how the ECM determines there's insufficient EGR flow. It's on the intake-side of the system and if not enough exhaust-gases flow ...

p0401 code ' Toyota Nation Forum
Aug 14, 2021
P0401 egr ' Toyota Nation Forum
Jul 19, 2012
P0401 Testing EGR insufficient flow - Toyota Nation Forum
Jun 18, 2015
More results from www.toyotanation.com

P0401 : EGR Flow Insufficient on 1996 Toyota Corolla

OBD-Codes.com https://www.obd-codes.com > forums > viewtopic
Jan 20, 2007 - on EGR codes, we recommend replacing the EGR, vacuum modulator and VSV (if equipped) and cleaning out the carbon buildup to the intake from the ...
If that finds nothing wrong, remove the EGR valve and bypass tube and check them for cleanliness and blockages. If they are blocked, follow your maintenance manual's instructions for cleaning them out so you do not damage the valve, then replace them and reset the ECM.

Insufficient EGR Flow - P0401 Code - Toyota

Here is a list of possible causes. Some things you have already done.

EGR solenoid valve harness is open or shorted
- EGR solenoid valve circuit poor electrical connection
- EGR volume control valve stuck closed
- Faulty EGR Pressure sensor
- Faulty EGR temperature sensor and circuit
- Faulty EGR Valve
- EGR passage clogged
- Exhaust gas leaks
Read more: http://engine-codes.com/p0401_ford.html#ixzz28fATCih2

This is not a cut and dry fault code. This means that more than one thing wrong can set the code in the computers memory. Here is the low down on the P0402 fault code. This is from the OBD2 fault code diagnostic book.

P0402 - Exhaust Gas Recirculation Flow Excessive Detected
Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Possible engine hesitation
Possible causes - EGR solenoid valve harness is open or shorted
- EGR solenoid valve circuit poor electrical connection
- EGR volume control valve stuck closed
- Dead (Weak) battery
- Faulty EGR temperature sensor and circuit
- Faulty EGR Valve
- EGR passage clogged
- Exhaust gas leaks

Common in automobile emission systems since the early 1970s, the EGR (Exhaust Gas Recirculation) valve controls an engine's emission of smog-causing nitrous oxides, or NOx. Its job is to route a portion of the exhaust gases back into the intake manifold. That lowers combustion temperature to below 2,500 degrees Fahrenheit - the temperature at which NOx gases form.

EGR flow is controlled by the engine's computer, which opens or closes the valve as needed. The EGR system is, for the most part, in the "out of sight, out of mind" category, and typical doesn't require regular maintenance. But if it gets clogged with carbon deposits, you'll see your "check engine" light come on, and a code (perhapsP0401or P0402 or P0403) will show that there is insufficient flow. That typically results from a vehicle being driven persistently on short trips that don't allow the engine to fully warm up. Flow problems also can be caused by carbon buildup due to failure to change the oil frequently enough.

A clogged EGR valve not only results in higher emissions, it can affect fuel economy and cause rough idling - even serious engine damage. Valves can usually be cleaned, but replacement is often recommended.

Advice? Make sure to put on some highway or freeway miles, and always change the oil according to the maintenance schedule in your owner's manual.

Hi, a Ford P0171 is a LEAN code for cylinder bank 1, and P0174 is a LEAN code for cylinder bank 2. These codes commonly occur on many Ford vehicles, and are set when the powertrain control module (PCM) sees the air/fuel mixture is running too lean (too much air, not enough fuel).
When the Check Engine Light comes on, either one of these codes, or both, may be found when a code reader or scan tool is plugged into the vehicle diagnostic connector. IF the vehicle is driven long enough, typically both codes will be set.
A P0171 lean code for bank 1 is the cylinder bank on the RIGHT (passenger) side of the engine on Ford vehicles with a V6 or V8 engine and rear-wheel drive.


A lean fuel condition may exist if the engine is sucking in too much air and/or the fuel system is not delivering enough fuel. If bad enough, a lean fuel condition may cause lean misfire, a rough idle, hesitation or stumble when accelerating, and/or poor engine performance.
Unmetered air can enter the engine through a vacuum leak, a dirty airflow sensor that is not reading airflow accurately, an EGR valve is not closing and is leaking exhaust into the intake manifold, an EGR valve that is allowing too much flow (because the EGR differential pressure sensor that monitors EGR flow is faulty and is under-reporting EGR flow).
If the problem is not enough fuel, the underling cause may be a weak fuel pump, restricted fuel filter, leaky fuel pressure regulator or dirty fuel injectors.

Are you reset the stored codes there? The EGR (Exhaust Gas Recirculation) valve controls an engine's emission of smog-causing nitrous oxides, or NOx. Its job is to route a portion of the exhaust gases back into the intake manifold. That lowers combustion temperature to below 2,500 degrees Fahrenheit - the temperature at which NOx gases form.

EGR flow is controlled by the engine's computer, which opens or closes the valve as needed. The EGR system is, for the most part, in the "out of sight, out of mind" category, and typical doesn't require regular maintenance. But if it gets clogged with carbon deposits, you'll see your "check engine" light come on, and a code (perhaps P0401 or P0402 or P0403) will show that there is insufficient flow. That typically results from a vehicle being driven persistently on short trips that don't allow the engine to fully warm up. Flow problems also can be caused by carbon buildup due to failure to change the oil frequently enough.

A clogged EGR valve not only results in higher emissions, it can affect fuel economy and cause rough idling - even serious engine damage. Valves can usually be cleaned, but replacement is often recommended.

About thie generic fault code, I suggtes check this description and tips for solution information: DTC-P0401-Tests (keep in midn that this code applied for alot brands, Hyundai included).

Keep us updated.

The EGR Valve and System - it's just three letters, but EGR can result in AGGravation.

Common in automobile emission systems since the early 1970s, the EGR (Exhaust Gas Recirculation) valve controls an engine's emission of smog-causing nitrous oxides, or NOx. Its job is to route a portion of the exhaust gases back into the intake manifold. That lowers combustion temperature to below 2,500 degrees Fahrenheit - the temperature at which NOx gases form.

EGR flow is controlled by the engine's computer, which opens or closes the valve as needed. The EGR system is, for the most part, in the "out of sight, out of mind" category, and typical doesn't require regular maintenance. But if it gets clogged with carbon deposits, you'll see your "check engine" light come on, and a code (perhaps P0401 or P0402 or P0403) will show that there is insufficient flow. That typically results from a vehicle being driven persistently on short trips that don't allow the engine to fully warm up. Flow problems also can be caused by carbon buildup due to failure to change the oil frequently enough.

A clogged EGR valve not only results in higher emissions, it can affect fuel economy and cause rough idling - even serious engine damage. Valves can usually be cleaned, but replacement is often recommended.

A code P0401 most likely means one or more of the following has happened:
* The DPFE (differential pressure feedback EGR) sensor is faulty and needs to be replaced
* There is a blockage in the EGR (tube), most likely carbon buildup
* The EGR valve is faulty
* The EGR valve may not be opening due to a lack of vaccuum

Possible Solutions: In fixing this code, it is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.
* Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open
* Clean out the EGR valve and/or tubing to remove deposits
* Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model)
* Replace the DPFE sensor (with a good quality / OEM one)
* Replace the EGR valve

A P0174 lean code for bank 2 is the cylinder bank on the LEFT (driver) side of the engine on Ford vehicles with a transverse-mounted V6 engine and front-wheel drive. This code is not set on four cylinder engines (no bank 2).
WHAT A LEAN CODE MEANS
A lean fuel condition may exist if the engine is sucking in too much air and/or the fuel system is not delivering enough fuel. If bad enough, a lean fuel condition may cause lean misfire, a rough idle, hesitation or stumble when accelerating, and/or poor engine performance . Unmetered air can enter the engine through a vacuum leak, a dirty airflow sensor that is not reading airflow accurately, an EGR valve is not closing and is leaking exhaust into the intake manifold, an EGR valve that is allowing too much flow (because the EGR differential pressure sensor that monitors EGR flow is faulty and is under-reporting EGR flow).
If the problem is not enough fuel, the underling cause may be a weak fuel pump, restricted fuel filter, leaky fuel pressure regulator or dirty fuel injectors.

Remove the EGR valve and clean it out. It's probably carboned up really bad constricting the exhaust flow. Also remove the EGR tubes and clean them out as well. I use brake cleaner and keep spraying the pieces out until it's pretty clean and re-assemble.

clean and recharge your cold air filter, if you never had it cleaned, you can buy the recharge kit for your cold air filter, follow the instructions, if that doesn't work check your mass air flow sensor, have your mechanic clean it and test it.