Question about 2001 Isuzu VehiCROSS

1 Answer

Replacing wiper arm

Both of my windshield wiper arms are rusted out so I'm planning on replacing them. I've never done anything like this before and assume it's pretty straightforward but I would appreciate any pointers or tips anyone may have. Thanks.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Once you loosten the golden bolt, do you just lift up the wiper arm? i tried doing that but nothing happened. i might just need to lift harder but i dont know for sure

Posted on Oct 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace a 99 se Bonneville windshield wiper motor


Windshield wiper motors are generally easy to replace. You need to remove the windshield wipers and take off the small grill panel above the hood and under the windshield. You should see the motor in there. It simply unbolts and unplug the electrical connector and replace it with a new one.

Mar 21, 2015 | 1999 Pontiac Bonneville

2 Answers

How do you replace windshield wiper motor on a 1997 ford e250 van


REMOVAL
  1. Raise and support the hood.
  2. Remove the windshield wiper pivot arms.
  3. Remove the cowl top vent panels.

25287270-15uk5heqgoha5mc4ejw3dmql-1-0.gif
  1. Disconnect the windshield wiper mounting arm and pivot shaft.
  1. Remove the access cover from the dash panel.
  2. Remove the mounting arm and pivot shaft retaining clip.
  3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

25287270-15uk5heqgoha5mc4ejw3dmql-1-2.gif
  1. Remove the windshield wiper motor.
  1. Disconnect the electrical connector.
  2. Remove the three bolts.
  3. Remove the windshield wiper motor.
INSTALLATION

25287270-15uk5heqgoha5mc4ejw3dmql-1-5.gif
  1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

25287270-15uk5heqgoha5mc4ejw3dmql-1-9.gif
  1. Install the windshield wiper motor.
  1. Place the windshield wiper motor in the dash panel.
  2. Install the three retaining bolts.
  3. Reconnect the electrical connector.

25287270-15uk5heqgoha5mc4ejw3dmql-1-14.gif
  1. Reconnect the windshield wiper mounting arm and pivot shaft.
  1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
  2. Install the access cover in the dash panel.
  1. Install the cowl top vent panels.
  2. Install the windshield wiper pivot arms.
  3. Adjust the windshield wiper pivot arms.
This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Nov 17, 2014 | Cars & Trucks

1 Answer

Removing windshield wiper arm from a 2000 Grand Prix


Sometimes you have to use a small gear puller. The arm could be tapered and is wedged onto the shaft.

Dec 05, 2012 | 2000 Pontiac Grand Prix

2 Answers

I have one wiper that does not work the other stops in the middle of the windshield how can i fix them


The motor could be bad, but it's likely that the ball joint connections under the hood area under the cowl have become disconnected for the one windshield wiper arm.

The connection of the arm that moves should be checked for being at the correct angle for parking.
Removal & Installation 2000-03 Wiper Motor and Bushing Replacement L4-2.2L (Vin F) & V6-3.0L (Vin R) To Remove:
sat_car_22_fw-wpr_arm_xp.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Remove the wiper arm finish caps
  3. Mark both wiper arm positions on the windshield by using a wax pencil or tape
  4. Remove or disconnect the following:
    • Wiper arm retaining nuts and washers
    • Wiper arms
    • Weather-strip at rear of hood sat_car_22_f_wshd_wthr-strp.gif

      sat_car_22_f_wshd_gril_nts.gif

    • Grill nuts from base of wiper arm shaft
    • Grill
    • Electrical harness connector from the wiper motor
    • Wiper motor retaining bolts
    • Wiper motor assembly from plenum area
    sat_car_22_f_wpr-mtr_asy.gif

    sat_car_19_wpr_mdl_rmv.gif

  5. If replacing wiper module bushings remove the steel bushing first then the rubber grommet
  6. Remove the wiper motor from the transmission assembly
To Install:
  1. Install or connect the following:
    • Wiper motor to transmission assembly NOTE: If the wiper module bushings were replaced install the rubber grommet first then the steel bushing.
    • Wiper motor to plenum area
    • Wiper motor retaining bolts; torque to 44 lb-in. (5 Nm)
    • Electrical harness connector to the wiper motor
    • Weather-strip at the rear of hood
    • Grill
    • Grill nuts to the base of the wiper arm shaft
  2. Install the wiper arm assemblies at the marks made during removal or at the PARK position if a new wiper motor is installed
  3. Install the wiper arm retaining washers and nuts; torque to 9 lb-ft. (12 Nm)
  4. Install the wiper arm finish caps
  5. Verify correct wiper system operation
prev.gif next.gif

Oct 05, 2010 | 2001 Saturn L-Series

1 Answer

The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
  1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
  1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
  1. Remove left windshield wiper adapter and connecting arm clip access cover.
  1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
  1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
  1. Disconnect battery and wiper motor electrical connector.
  1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
  1. Disconnect the battery ground cable (14301).
  1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
  1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
  1. Reach through the access cover opening and unsnap the wiper motor clip.
  1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
  1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
  1. Remove nut and ground strap.
  1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
Installation
  1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
  1. Install nut and ground strap.
  1. Connect wiper motor electrical connector.
  1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
  1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
  1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
  1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
  1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
  1. Test the system.
6bd608c.gif

Jan 04, 2010 | 1983 Ford Ranger

1 Answer

Removing/replacing wiper motor in '93 Ford Ranger


You don't have to put the wipers in an upright position You can take the arms completely off. It's very easy to do, when you are looking at the base of the wiper arm, on the side closest to the windshield, at the base, there is a spring-loaded tab. Lift the arm on its hinge to where the arm is now pointing away from the windshield, pull the tab and the wiper arm will slide right off. Now you can access the linkage joints easily. Hope that helps!

Nov 09, 2009 | 1993 Ford Ranger SuperCab

2 Answers

Wipers on 2002 Lincoln quit working


Hi, your windshield wiper motor needs to be replaced. The wiper motor on your car in located under the hood. Follow the windshield. At the bottom towards the center, under the hood, you will see a large piece of plastic that runs from the center to the fender. This needs to be removed to get to the motor. Once removed, you will see the motor the "arms" attach too. Unfortunately the "transmission" or arms have to be removed from the motor before the three motor screws come off. If there is rust at the contact point, or if the contact point is seized from corrosion/rust, try a rust loosening lubricant, but don't bend the arms from using too much force. Also be careful not to crack the windshield if your using a breaker bar under the arm to disengage it from the motor. After the arms are disconnected, remove the three screws holding the motor in place, and remove the electrical connection to the motor. When buying a new or rebuilt motor, make sure to bring the bad one in to compare, especially the length of the part where the arms attach. This has to be exactly the same, not longer or shorter. Prices around here in the midwest run about $65 for new motor.

Jul 13, 2009 | 2002 Lincoln Town Car

1 Answer

Wiper motor replacement


SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the windshield wiper pivot arms (17527).
    1. Remove the nuts (one each side).
    1. Remove the windshield wiper pivot arms.
  1. Remove the LH and RH cowl top vent panels.
    1. Remove the hood weatherstrip.
    1. Remove the screws.
    1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.
  1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
    1. Remove the nuts.
    1. Remove the bolt.
    1. Position the windshield wiper mounting arm and pivot shaft assembly aside.
  1. Remove the windshield wiper mounting arm and pivot shaft assembly.
    1. Disconnect the electrical connector.
    1. Remove the windshield wiper mounting arm and pivot shaft assembly.
----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal
  1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .
  1. Remove the windshield wiper motor (17508).
    1. Remove the output shaft bolt.
    1. Remove the bolts.
    1. Remove the windshield wiper motor.

May 01, 2009 | 1999 Lincoln Town Car

2 Answers

How to a remove the wiper arm


Most windshield wiper arms usually fail due to a loose nut or rusted and worn out parts. Fixing this depends on how the wiper arm attaches to the vehicle. Fixing wiper arm failure is usually as easy as tightening a nut or replacing a worn out or rusted part.

Here is a step by step guide on fixing this issue.

Step1 49869_65x95_aspect.jpg Mark the existing wiper position on the windshield using a crayon. This will help you align the wiper arm correctly when you install a new one. Alternatively you can use the Trucks own markings. At the bottom center of the windshield you will see writing and three small dots. The wiper should rest on top of these dots. Step2 49870_65x95_aspect.jpg Follow the wiper arm down to where it connects with the Truck. You should find a hinged cap at the end. Step3 49871_65x95_aspect.jpg Lift this cap to reveal the nut and screw underneath. Step4 49872_65x95_aspect.jpg Use a wrench (or socket and ratchet) to loosen the nut. Step5 49873_65x95_aspect.jpg Remove the nut completely, leaving the screw stud exposed and the wiper arm free to be removed. Step6 49875_65x95_aspect.jpg Lift the arm straight up. Wiggle the arm and pull upwards at the same time until the arm slides free of the screw. If it seems stuck, push the arm back down and proceed to Step 7. Step7 49876_65x95_aspect.jpg Use a battery cable puller to pry the arm loose. Arrange so the large puller screw cap sits on top of the wiper arm screw. The outside arms have flat fingers that should be fitted underneath the wiper arm. Step8 49877_65x95_aspect.jpg Grasp the handle at the top of the puller and turn clockwise. The puller screw will push down on the wiper arm screw and simultaneously pull up on the wiper arm. A few slow turns should pop the wiper arm free.

Mar 24, 2009 | 2002 Nissan Frontier Crew Cab

1 Answer

Driver side wiper arm


toward bottom of windshield above passenger wiper before starting make sure your wipers are in the park position please rate this answer thanks.

Feb 01, 2009 | 1999 Dodge Caravan

Not finding what you are looking for?
2001 Isuzu VehiCROSS Logo

Related Topics:

401 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...