Question about 2006 Dodge Charger

1 Answer

Charger seat switch or swap

I recently purchased some srt8 charger seats which have heating and cooling in both drivers and passengers seats as well as both are automatic. I own a 2006 sxt charger and wanted to know if it was possible to change my old seats for the new ones, thing is I installed the new ones but the cable or plugs are not the same, so I am trying to see if there might be some other cables under the rug that have the correct adapter or what would be the best way to do this.

Posted by on

Ad

1 Answer

No way you can make them work properly.

  1. wiring is completly different
  2. controlers are different
  3. all controled by the TIPM

Posted on Jul 02, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Seat heater comes on by itself in 2004 yukon denali


Heated Seat Components
The heated seat system consists of the following components:
• Driver and passenger heated seat switches
• Driver and passenger seat back heater elements
• Driver and passenger seat cushion heater elements
• Driver and passenger seat back temperature sensors
• Driver seat module
• Driver door module
• Passenger door module
When there are modules involved in the operation of any componet that's acting up , the module's electronic's could be the culprit ! But without testing who's to say what the problem could be !
I would have it check for DTC'S
DTC B2425 or B2430
The driver and passenger seat heaters are controlled by the driver seat module. Power is supplied to the driver seat cushion and back heater elements through individual voltage supply circuits. Power is supplied to the passenger seat cushion and back heater elements through a common voltage supply circuit. All of the driver and passenger seat heater elements are grounded by the driver seat module through individual low side drive control circuits. The heater element control circuits are pulse width modulated to ground by the driver seat module in order to control the seat temperatures by regulating the current flow through the heater elements.
DTC B2435 or B2440
The driver seat module relies on inputs from thermistors installed in the driver and passenger seat backs to control heated seat temperatures. The thermistors are 2-wire sensors supplied with a 5-volt referenced signal circuit and low reference circuit from the driver seat module. Resistance through the thermistors varies with temperature causing the heated seat sensor signal circuit voltage levels to decrease as the seat back temperatures rise.
Install a scan tool.
Start the engine.
Turn the heated seat ON.
With a scan tool, observe the Heated Seat Sensor parameter in the data list for the driver seat module.
Does the scan tool indicate that the heated seat sensor parameter is within the specified range?
0.078-4.94 V

Dec 08, 2016 | GMC Yukon Denali Cars & Trucks

1 Answer

2007 Buick Lucerne CXL: Cooled seats not working. LIghts come on, temperature adjusters work but the motors under the seats do not come on.


Air Circulation
When the heated/cool seat switch is pressed to initiate operation of the climate control seat (CCS) system, cabin air is drawn through the heated/cool ventilation module air filter, then directed through passages in the foam of the seat cushion and seat back to the seat's occupant. In order for the CCS system to operate to its optimum performance, it is crucial to have unrestricted air flow through the system. A dirty or restricted air filter, the blockage of an exhaust air duct, a misaligned heated/cool ventilation module, or incorrect foam installation of the seat cushion or seat back will all have negative effects on CCS operation.
Heated/Cool Ventilation Module
Each heated/cool seat has 2 ventilation modules, one located under the seat cushion and one located in the seat back. These modules are controlled by the climate control seat module (CCSM). Each ventilation module contains a thermo-electric device (TED), a temperature sensor, and a blower motor. The TED and temperature sensor are mounted downstream of the blower motor. Each TED consists of a circuit of positive and negative connections sandwiched between 2 ceramic plates. Each ceramic plate is equipped with copper fins for heat exchange. The air flowing past these fins is either directed as conditioned air into the seat cushion and seat back, or directed into the cabin as waste air.
A TED is essentially a solid state heat pump that is used to heat or cool the air supply to the seat cushion and seat back. When voltage is applied to a TED, one side releases energy as heat, while the opposite side absorbs energy and gets cold. When the polarity of the current flow to the TEDs is switched, the hot and cool sides of the TED reverse.
During the following climate control seat system description and operation, the TEDs, blower motors, and temperature sensors will be referenced independently even though they are all packaged together as a module.
Climate Control Seat (CCS) System
The CCS system consists of two heated/cool ventilation modules and one climate control seat module (CCSM) that controls both the driver and passenger heated/cool seats systems. The CCSM is mounted below the front passenger seat cushion. It receives power from both, battery positive voltage and ignition 3 voltage.
Once a CCS system is activated, cabin air is drawn through the seat blower motors and directed across the fins of each of the thermo-electric device (TED) located under the seat cushion and in the seat back. The air is either heated or cooled as it passes over the TEDs. This conditioned air is then directed through channels in the foam of the seat pad and through small holes in the seat cover to the occupant. Once the system is activated, the CCSM uses a set of algorithms to control the temperature of the selected heating or cooling modes.
Your best bet is to take your vehicle to a qualified repair shop an have it diagnosed .
DTC B19A4: Driver Seat Back Blower Speed Circuit High

DTC B19A8: Driver Seat Back Blower Speed Circuit Short to Ground

DTC B103D: Driver Blower Power Circuit

DTC B272E: Driver Seat Back Blower Circuit Open
DTC B19A3: Driver Seat Cushion Blower Speed Circuit High

DTC B19A7: Driver Seat Cushion Blower Speed Circuit Short to Ground

DTC B2729: Driver Seat Cushion Over Temperature
DTC B19A2: Passenger Seat Back Blower Speed Circuit High

DTC B19A6: Passenger Seat Back Blower Speed Circuit Short to Ground

DTC B111D: Passenger Blower Power Circuit

DTC B272F: Passenger Seat Back Blower Circuit Open
DTC B19A1: Passenger Seat Cushion Blower Speed Circuit High

DTC B19A5: Passenger Seat Cushion Blower Speed Circuit Short to Ground

DTC B272A: Passenger Seat Cushion Over Temperature
Driver and Passenger Heated/Cool Seats Inoperative
  1. Ignition OFF, disconnect the C1 harness connector at the CCSM.
  2. Test for less than 5 ohms between the ground circuit terminal M and ground.
  3. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  4. Verify that a test lamp illuminates between the B+ circuit terminal E and ground.
  5. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

  6. Disconnect the C2 harness connector at the CCSM.
  7. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  9. If all circuits test normal, replace the CCSM.


Sorry

Jul 10, 2016 | 2007 Buick Lucerne CXS Sedan

1 Answer

2010 Lincoln MKS Heated Seat on driver's side stopped working (Light in button turns off on its' own)


The most common cause of this problem is that the drivers seat heater grid is open or burned out. That is based on 25 years as a Ford dealer technician.

Feb 27, 2017 | Lincoln Cars & Trucks

1 Answer

Manual trunk release 2012 dodge charger


the operator guide missing in just 2 years.
did you look in 3 tops locatons
dash
glove box
side of drivers seat.
first

Jan 19, 2015 | 2012 Dodge Charger SRT8 Sedan 6.4L V8...

1 Answer

I have a 2007 Dodge Charger. The local garage uploaded an undate on the computer, (per a bulletin from Dodge) because the engine light was on and would not pass emissions. After the upload he said all the...


Why are you not back at the shop to
have them complete the work properly?

We simply can't know or guess at these
vehicle problems, from a chat room,from home

Apr 23, 2014 | 2007 Dodge Charger SRT8 Sedan

1 Answer

My 2007 Dodge SRT8 charger stalled possible problems?


My 2007 Dodge SRT8 charger stalled possible problems?

I was reversing out of the driveway and when i put it in drive it stalled out. Its chugged before, just once, and recently just bought the car Im thinking fuelicon1.png filter or spark plugs...any suggestions?

Oct 19, 2012 | 2007 Dodge Charger SRT8 Sedan

1 Answer

I have a 2008 Chevrolet Silverado 1500, extended cab, automatic truck.......PROBLEM, the drivers side has a power seat, it will not move in any direction and the passenger side front and rear power windows...


How to diagnose this problem ? Viewing wiring diagrams to see what all is invovled in these electrical circuit's , check power supply's an ground connection's using a DMM - digital multimeter !
What type power seat's ? does it have memory ,heated an cooled etc ?
Power Seats System Description and Operation
There are 2 options of power seat systems available in full size trucks. The first is 6 way driver and passenger power seats without memory. The second is an 8-way driver seat plus 4-way lumbar with memory, heat and optional cool function. While the passenger has 8-way power seats with heat and optional cool function. For the driver memory seat operation, refer to Memory Seats Description and Operation. Power seats without memory are completely controlled through the power seat switch. Battery voltage is supplied to the power seat switch through the power seat circuit breaker. While the seat adjuster switches are in an inactive state the switch contacts are closed to the power seat switch ground circuit. When a power seat switch is pressed to an active state the switch contact is closed to the battery voltage supply circuit. Each seat adjuster motor is controlled by the power seat switch through 2 motor control circuits. The seat adjuster motors are bidirectional and the direction of adjuster motor rotation is determined by which of the adjuster motor control circuits is switched to battery voltage while the other remains grounded.

If it has memory seat's there is a control module !
Battery voltage is supplied to the driver seat module through a 25 A circuit breaker. The driver seat module supplies the seat adjuster switch assembly with a battery positive reference voltage. While the seat adjuster switches are in an inactive state the switch contacts are closed to the adjuster switch common circuit.
Both right side windows have a seperate power supply from the left side window's ,has RT DOORS circuit breaker CB1 - 25amp. location left instrument panel fuse block . Circuit breaker's very rarely fail .Do the door lock's work on that side of the vehicle ? The windows won't work with their own switche's ?
The DDS controls the passenger window through a GMLAN message to the PDS. When a power window switch is activated in the up or down positions the PDS supplies power and ground to the window motor control circuits to drive the window motor in the required direction. Prior to activating a power window motor the PDS will supply the control circuit with a low current bias voltage in order to determine that a short to ground condition does not exist, and during window motor operation the PDS continues to monitor the motor current to verify proper window motor operation. (Scan tool support is available for this system)
Check PDM fuse 4 15 amp ,this supply's B+ voltage to the DOORLOCK/WINDOW switch passenger side . Check for broken wires inside the flex boot from the body to the passenger door .

Nov 18, 2017 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Passenger heated/cool seats not working


The seat switch or the heated seat relay is bad.Always check your fuses first.

Aug 01, 2009 | 2003 Ford Expedition

1 Answer

Buick Lesabre Heated Seats not working


The problem is most likely caused by shorted heating grids in the seat cushion itself, kind of like the heating element in an electric blanket, very expensive to replace.

Dec 12, 2008 | 2003 Buick LeSabre

2 Answers

Heated seat


Could be that the wiring for the heater is broken, or that the heating element itself has been damaged. Has anyone knelt on the seat when reaching in to get something out of the car? Or has anyone stood on it (a child maybe)? Pressure like that can break the heaters and keep them from firing up.

Sep 16, 2008 | 2006 Ford Freestyle

Not finding what you are looking for?
2006 Dodge Charger Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...