Question about 1998 Chevrolet Blazer

1 Answer

Engine mounts im replacing a motor but not sure where the motor mounts are located?

Posted by on

  • Anonymous Mar 27, 2014

    Can only find 2 motor mounts, replaced the one from engine to transmission, but can't seem to locate the third motor mount. Do you have a diagram so I can locate the 3rd mount?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 702 Answers

The engine mounts are found one on each side about the center of the engine at the bottom at the frame. There is a long bolt with a nut that holds the engine side of the mount to the frame side of the mount.

Posted on Jun 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ok I have a 1995 ford aspire im trying to figure out how to replace the oil pump


Disconnect the motor mounts and jack the engine to remove the oil pan. Remove the oil pan, replace the oil pump you'll find at the end of a pick up tube, replace the pump and put the pick up tube back on the new pump making sure it's in the same low position it was when removed, replace the oil pan gasket and put the oil pan back on, lower the engine and put the motor mount bolts back in. Put in the proper amount of oil and go.

Nov 13, 2014 | 1995 Ford Aspire

3 Answers

Im buying this truck for $500. the only thing i hear wrong with it is the motor shakes bad almost like the bolts mounting to the tranny r bad. can those bolts be replaced and the motor and tranny stay...


i would check the motor mounts to make sure the bolts are tight, then i would check the rear transmission mount bolts, also to make sure they are tight. yes , if the bolts mounted to the tranny need to be replaced, you can normally get them from a auto part store.

Feb 18, 2011 | 1983 GMC S-15 Pickup

1 Answer

I need to jack up the motor and cant find the mounts. im trying to take out the oil pan


Not sure what engine you have , but if it is a tranverse mounted engine , the mounts are probably at the top of the engine one on each side. Jamed between the shock tower and the motor.

Dec 02, 2010 | 1993 Chrysler Concorde

2 Answers

Dodge neon sxt 2003 engine vibration while increasing rpm


Well i have s similar sound but im not sure if its the same. For me i just found out that its a bracket i never put back on. The motor mounts if you get them at an autozone which gives you a life time warrenty runs about 30 bucks and theres only 3 upper passenger and lower passenger and one on the drive side which is connected to the transmission. there is some what of a 4th one but that one never really goes bad and its the worst one of them all. Its located in between the 2 on the passenger side you have to move the engine outa the way to get to it and take it out. Im not sure if autozone or any place sells that one but like i said its probably still ok. i have 170000 mile on my neon and the mounts still good and trust me my cars been through alot and i mean alot its flied over cannels anyway yea so thats what i know about the mounts im not sure why the noise though. I say check the motor mounts if any are ripped change the ripped ones all at once trust me. Oh and i didnt the change on the motor mounts myself so it was free there not hard to change the first 3 i mean maybe the transmission one too all you need is a jack underneath it to keep it leveled right.

Jan 02, 2010 | 2003 Dodge Neon

2 Answers

Need blower motor replacement info .need to replace heat/ac blower mtr,mounting plate and regulator-where are they located?need diagram or procedure


They are under the wiper assembly under the hood. Remove partial firewall, wiper assembly and "cage" for the motor. The regulator is under the motor. I would check the strip fuse first its but the drivers sidestrut mount in a tootsie roll sized plastic snap container.

Jul 09, 2009 | Mercedes-Benz E320 Cars & Trucks

1 Answer

Engine mount replacement


There are two liquid filled and a trans mount. You need to found out which way the motor jumps if it jumps back to the fire wall I would change the two liquid fill. They are located looking at the engine on the pulley side left and right bolted to A-frame you can change one at a time. Unbolt one and jack motor with a floor jack and board just lift enough to drop it in and out. It's tough I know I did it before but it can be done. And do the same for the other. Trans mounted one never needs replaced. Just make sure the mounts are bad cause front wheel drive motors usally move but if its moving more than 2"-4" then replace them.

Apr 24, 2009 | 1994 Ford Taurus

1 Answer

Backside of engine


There is a special tool you need to purchase . It connects on your front motor mount located on top by radiator.. This is what is called the dog bone in the industry . The specialty tool is put in the place of dog bone mount and is adjustable whith vehicle placed in neutral... The tool pulls the motor towards the radiator giving you complete easy access and complete visibility for what you are trying to achieve

Dec 26, 2008 | 1997 Pontiac Sunfire

1 Answer

Need to replace the starter in a 1999 mercury couger V6 manual trans, and not sure on its location. Im thinking its up top under the plenum but not sure.


nope... it's on the bottom of the motor... or rather mounted there... i'm not familiar with that car... is the motor in sideways or front to back.... either way... the starter drives a gear on the back of the motor located where the transmission is bolted onto the motor. so look at that spot on either side of the motor on the bottom.. best to just lay on the ground and look up at the motor... unless you have car ramps you can drive the car up on. be sure to unhook the battery... usually two bolts hold it on.... drop the starter... unhook the cables and make sure you put them on the new starter the same way... mount the starter back on and tighten the bolts and you are good to go.

you do know for sure the issue is the starter ?

Robert

Dec 17, 2008 | 1999 Mercury Cougar

2 Answers

1995 Eagle Talon


Motor Mount Replacement/Repair

Give Your Engine A New Life With A Motor Mount Replacement
A Motor Mount acts as a security mechanism for the engines, minimizing the adverse effects of frequent vibrations and oscillations that arise when driving the vehicle. No matter how powerful the engine, there is a need for some internal mechanism inside the vehicle to provide strong support to the engine and to protect it from any damage. The Motor Mount serves as essential and rigid structural support systems for the engine, enabling the vehicle to get through the irregularities of the track and other road conditions smoothly and conveniently. It secures the engine and prevents it from serious damage. Moreover, it minimizes vibration and noise on the part of engine.
Due to prolonged usage, Motor Mount will not be able to deliver its services properly. In order to avoid the risk of total breakdown of the engine, the working conditions of the motor mount needs to be checked regularly .Whenever the needs arises it should be replaced as it affects the overall performance and efficiency of the vehicle. Failure of the engine mount can seriously damage the engine .Auto-part replacements ensures the longevity of the engine and it enables you to fully utilize the benefits of smooth drive.
Points of consideration for replacing and repairing
  • Cracking of distributor caps needs to be avoided
  • Radiator hoses should not be torn.
  • Before opening the engine, firewall must be checked for clearance.
  • Engine should not be jacked directly by the oil-pan, as the pan may bend.

Replacement Procedure
  • First of all, remove the hood and all the parts required for access to engine.
  • Remove the engine mount through the bolts.
  • Secondly loose the mount to frame bolts.
  • Raise the engine slowly towards upward direction to remove the engine mount brackets and then, ultimately remove the motor mount and the engine mount fasteners; the shims locations needs to be noted down.
  • Heat shields or Drip shields must be transferred to the new mount after comparing it with old mount.
  • Progressively old Mount is replaced with the new one.

Re-intallation of Engine Mount
  • Engine Mount brackets, fasteners and shims must be installed in their original locations.
  • Mount-to frame bolts should be placed in their appropriate locations.
  • Reinstall engine, mount through bolts loosely and allow the vehicle to run two or three times so that engine mount can adjust at their accurate operating locations.
  • Finally, the engine is placed in its accurate place by pushing it inside and all the bolts are tightened.
  • Make sure that engine is properly aligned.
  • Reinstall all the removed parts.
  • Reinstall and align the hood at correct place.

Aug 21, 2008 | 1995 Eagle Talon

1 Answer

REPLACING MOTOR MOUNTS IN A 1966 PONTIAC LEMANS WITH A V8


1. GET THE RIGHT RUBBER MOTOR MOUNTS,

2.FIND THE MOTOR MOUNTS LOCATED UNDER YOUR ENGINE. MAYBE THREE. FRONT LEFT, RIGHT AND MIDDLE BEHIND,

3.JACK UP THE ENGINE A LITTLE BIT, PUT MOTOR MOUNT IN AND USE THE SAME SCREW TO TIGHT IT

4. CHANGE ONE AT A TIME.

5. STABLE YOUR CAR, BE SURE IT IS COMPLETELY SAFE, USE EMERGENCY BREAK AND A BLOCK TO STABLE THE CAR UNLEASE YOU HAVE HOIST.

Jul 08, 2008 | Pontiac LeMans Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...