Question about 2003 Pontiac Grand Am

1 Answer

Blower fan when I turn the fan on the first three positions have stoped working but the fourth and fifth still work ,would it be in the switch or the blower motor.if it is the switch ,can I change just the switch or the whole module .

Posted by on

  • libsky Aug 20, 2008

    blower wont turn on first three positions but turns on , on the fourth ,ford focus



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 500 questions.

  • Expert
  • 611 Answers

Its ur blower motor resistor by ur blower

Posted on Jun 22, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My blower stoped working you can get it to work

If your blower motor has only one terminal going to it that means the switch is where the problem is. Blower motors like this are controlled by a switch that has a rheostat or resistors built in to the switch.

When you turn the switch to the low position the fan runs slow because of more resistance thus reducing the voltage to the motor. When you turn the fan to the high position the fan runs at full speed because it is getting 12 volts.

Now some switches use a electronic board to control the speed. You need to do a search and replace the fan control switch.

One other thing - my Volvo had the same problem and I ended up replacing the whole dash module - new it costs $325.00 but I picked one up at the junk yard "pull-a-part" for $35.00.

Mar 13, 2015 | Cars & Trucks

1 Answer

Sentra AC

There's a 10amp fuse that powers the ac clutch relay and compressor. There are 15amp fuses that power the blower motor and the ac control switch. All of those fuses get power from the key switch. The resistor and fan switch provide the ground circuit for the blower motor.
I would want to know if those fuses are getting power, and if the control panel is working. You should be able to ground the blower motor and make it run on high, and that should not have any effect on if the ac compressor is running or not.
It could be a key switch problem in that the circuit is not strong enough to handle the load from the blower and the compressor at the same time.

Jun 21, 2013 | Cars & Trucks

1 Answer

After i change thebrake switch will my fan blower for my heater and ac start working agian

No it won't.The brake switch is for brake light,interlock shift solenoids,transmission TCC controls,and stoping the vehicle, You fan blower has a completely different power supply that is independant from the brake electrical system, For you fan blower to operate its either the fan resistor blower or the fans control switch to the fuse

Mar 19, 2012 | Cars & Trucks

1 Answer

Motor fan not working taurus 2000

tap on the fan motor while it is turned on. if it comes on than replace the fan motor. There is a blower motor resister that is bolted next to the blower motor tha may be bad. Test it with a test light. It has three wires that light up each time you move the selector switch to a different position. If it changes than replace the blower motor which is located behind the glove box next to the floor board.

Oct 27, 2010 | 2000 Ford Taurus

1 Answer

The heater fan stoped workin

Check the blower relay,and the blower switch.

Feb 06, 2010 | 2003 Kia Spectra

2 Answers

I have a 1994 dodge caraven se the heater switch worked fine in all three setings then the low and med stoped working it still works on hi what could be wrong?


Aug 03, 2009 | 1994 Dodge Caravan

1 Answer

2001 Chevy Blazer blower motor not working

It keeps burning out blower resistors because of the blower motor drawing to much amperage so you will need to replace the resistor and blower motor

Jun 27, 2009 | 1988 Chrysler Fifth Avenue

1 Answer

Air conditioner on 2006 colorado crew cab not working

your truck needs a blower resistor it controls all the other fan speeds, its located in the cab mounted to the face of the heater box.

Mar 19, 2009 | 2006 Chevrolet Colorado

1 Answer

Fan control switch

the blower resistor and pigtail will need to be replaced. good luck ive seen this problem a lot of times mr gm ha ha

Nov 23, 2008 | 2005 Chevrolet Silverado

2 Answers

Blower fan not working correctly

It is the blower motor resistor and is located under the glovebox behind the blower motor.

Nov 19, 2008 | 2003 Oldsmobile Alero

Not finding what you are looking for?
2003 Pontiac Grand Am Logo

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides