Question about 2007 Ford Ranger FX4 Off-Road

1 Answer

How do i clear fault codes in my 2010 ranger without a scanner?thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 277 Answers

Goto most any auto parts store and ask them to clear the codes.

Posted on Nov 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2010 ford edge has a slight flutter at 30 mph without a check engine light and no codes


If it has a check engine light then there are fault codes, have them checked with a better scanner, the one you used may have the wrong protocol or is defective. You may need a shop or Ford dealer to look into this and read the fault codes.

Feb 02, 2017 | 2010 Ford Edge

1 Answer

2010 Ford ranger, slips out of gear (from drive to OD) NO check engine light NO code, New filter and oil ( 2.3 automatic ).


Could be TCC solenoid, sticky valves/ valve body, or torque converter. Could be clutch bands also. Needs to be on a scanner.

May 22, 2015 | 2010 Ford Ranger

1 Answer

Clear fault codes


use the scanner on obd 2 generic to retrive or clear codes

Sep 08, 2014 | 1999 Mercedes-Benz SLK

2 Answers

Reset check engine light on a 2008 Buick Enclave without going to a garage


Anyone with a scanner can erase the codes and reset the light. On older cars, you could just remove the negative battery post for a few minutes, but that is not recommended for newer cars. Erase codes with a scanner.

Dec 09, 2013 | Cars & Trucks

1 Answer

Hyundai 2008 error code u0101


do you have at all a scanner to check and know what your code is all about. As I remember long time ago I had this situation and if I am not mistaken was about transmissionj control unit. I thing the case Happened to me was that the Automatic transmission connector was not well connected and I removed it clean it and reconnect and clear the fault code with my scanner and drove it with not any fault. try it and we will see.

Aug 27, 2012 | 2010 Hyundai Accent

1 Answer

How to clear code 118 and 224 on 1994 ranger


Ford Ranger/Explorer/Mountaineer 1991-1999
Clearing Codes

Print


CONTINUOUS MEMORY CODES

These codes are retained in memory for 40 warm-up cycles. To clear the codes for the purposes of testing or confirming repair, perform the code reading procedure. When the fault codes begin to be displayed, de-activate the test by either disconnecting the jumper wire (meter, MIL or message center) or releasing the test button on the hand scanner. Stopping the test during code transmission will erase the Continuous Memory. Do not disconnect the negative battery cable to clear these codes; the Keep Alive memory will be cleared and a new code, 19, will be stored for loss of PCM power.


KEEP ALIVE MEMORY

The Keep Alive Memory (KAM) contains the adaptive factors used by the processor to compensate for component tolerances and wear. It should not be routinely cleared during diagnosis. If an emissions related part is replaced during repair, the KAM must be cleared. Failure to clear the KAM may cause severe driveability problems since the correction factor for the old component will be applied to the new component.
To clear the Keep Alive Memory, disconnect the negative battery cable for at least 5 minutes. After the memory is cleared and the battery reconnected, the vehicle must be driven at least 10 miles so that the processor may relearn the needed correction factors. The distance to be driven depends on the engine and vehicle, but all drives should include steady-throttle cruise on open roads. Certain driveability problems may be noted during the drive because the adaptive factors are not yet functioning

Jun 03, 2012 | 1994 Ford Ranger Supercab

1 Answer

My 2010 ranger idles fine when cold, but cuts out when idling warm


Have a local shop or auto parts store read the fault codes, it sounds as if you may have an o2 sensor that is out of range.

Dec 26, 2011 | 2010 Ford Ranger

1 Answer

Diconected passenger airbag switch on 2003 f-150 single cab for stereo install now light on dash cluster flashes twice then solid, then again. No light on switch either, Thanks


did you plug the switch back in????, if so, you created a fault code. with the light not coming on it seems that you might have popped a fuse, check your fuses, if your sure that your fuses are all ok, try disconnecting the battery for about 5 minutes to try to clear the code, if that does not work, get your hand on a code scanner, and clear the code, if the code comes right back, you still have a fault in the air bag system.

Aug 26, 2010 | 2003 Ford Ranger Regular Cab

2 Answers

I Keep Getting A P171 Code on my 1997 Ford Ranger Pickup With a 4 Liter Engine


Code 171 is, "too lean", it could be as simple as a dirty fuel filter. If you already tried that then it's most likely the intake gasket is leaking. The O-rings get old and hard and don't seal so the engine is sucking in air where it shouldn't be. This is a common problem with those vehicles it's not too bad of a job to fix, I think Ford offers an update kit for less than $100.

Nov 10, 2009 | 1992 Ford Ranger

Not finding what you are looking for?
2007 Ford Ranger FX4 Off-Road Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...