Question about 1992 Dodge Dynasty

1 Answer

The ignition keylock cylinder will not turn with the key in it even after removing the swich assembly from the column. What next?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 40 Answers

Look at your key, does it look to be very worn?? This is normally the cause of a key not working and also the cheapest way to see if the lock itself is bad. Take the key to a locksmith and tell them you need the key copied using the code cutter. What they should do is take your key and read it and cut you a brand new key.

Posted on Nov 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The Key FOB is stuck in the ignition. How can I get it to eject?


Most if not all vehicles have a Electronic Park Lock (EPL)/Ignition Lock Cylinder Control Actuator: If the vehicle is equipped with automatic transmission and a floor mounted console gear shift, it has an ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in any position other than PARK and the vehicle may still be moving. The column ignition lock system consists of an ignition lock cylinder control actuator, and a park position switch that is located in the automatic transmission shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column. Or it has
Linear Shift Assembly: If the vehicle is equipped with a column mounted gear shift, it has a linear shift assembly on the steering column. The linear shift assembly has a cable that runs from the linear shift assembly to the ignition lock cylinder case. The purpose of this cable is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The linear shift assembly cable contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.
Your best bet is to take it to a ASE certified repair shop or the dealer ! The fix involves taking the steering column apart an or the floor shifter assembly ! Also electrical test to determine what is the problem !
Your

Jul 04, 2015 | 2008 Volvo S80

2 Answers

How to remove the ignition lock cylinder from a 93 geo storm


is the lock assembly in the car or out?
there are 2 jobs here, removing the assembly
and after that, attacking the lock it self.???????

any lock smith can rebuild the lock, proper
it has pins that are pressed out.
it can even be rekeyed.

the remove assembly is covered in the FSM, no books?
alldata.com covers that.
it really is an Isuzu. impulse.

my guess is its job 1, assembly out.
so toss coin lands on job1
(on most cars, steering wheel must be removed)
once that is done, its obvious from there, right? that clamp there with the antitamper screws? then must be removed. and replaced new..

a rare car , and even more one that runs....

here is the online FSM answer

  1. Remove the negative battery cable.
  2. Remove the steering wheel.
  3. Remove the combination switch assembly.
  4. Turn the key to the OFFposition, depress the retaining pin and remove the ignition lock cylinder from the switch.
  5. Disconnect the electrical connector from the ignition switch.
  6. Remove the snapring and spacer collar from the steering shaft.
  7. Disconnect the back drive cable from the ignition switch.
  8. Remove the ignition switch bolts and the ignition switch from the steering column.


now back in?
  1. Install the ignition switch to the steering column and tighten the bolts.
  2. Connect the back drive cable to the ignition switch.
  3. Install the spacer collar and the snapring to the steering shaft.
  4. Connect the electrical connector to the ignition switch.
  5. Install the lock cylinder into the switch.
  6. Install the turn signal switch screws and the turn signal switch.
  7. Install the four screws and the coil assembly to the turn signal switch.
  8. Connect the coil assembly wiring harness to the turn signal switch.
  9. Install the two piece steering column cover and the two piece steering column cover screws.
  10. Raise the steering column and install the upper steering column mounting bolts. Tighten the bolts to 18 ft. lbs. (24 Nm).
  11. Install the left lower dash trim panel and tighten the lower dash trim panel screws.
  12. Install the lap air deflector and tighten the lap air deflector screws.
  13. Install the knee pad assembly and tighten the five screws, the bolt and the nut attaching the assembly.
  14. Install the engine hood opener cable.
  15. Install the engine hood opener and tighten the two screws.
  16. Connect the electrical connector to the cigar lighter bezel and install the bezel.
  17. Connect the electrical connector to the left switch bezel and install the bezel.
  18. Install the steering wheel.
  19. Connect the negative battery terminal to the battery.

that?

Oct 08, 2014 | 1993 Geo Storm

1 Answer

Key stuck in ignition pontiac sunfire


ignition keylock cylinder broke. you have to remove ignition switch and remove keylock cylinder and replace ignition switch keylock cylinder with new ignition key then you have to reset theft security system which dealership has to fix.

Jan 27, 2013 | 1999 Pontiac Sunfire

1 Answer

The ignitioe will not turn out of the off position, the steering column will not lock and transmission shifter depresser button presses but will not move out of park.


SOUND LIKE IGNITION SWITCH KEYLOCK CYLINDER BROKEN. IN WHICH YOU CANT GET CAR OUT OF PARK.THE KEY LOCK CYLINDER BY TURNING THE KEY.IT MOVES A GEAR AND RACK ASSEMBLY THAT IN TURN MOVES THE IGNITION SWITCH ACTUATOR ROD AND PLUNGER TO VARIOUS POSITIONS REQUIRED FOR PERFORMING IGNITION SWITCH FUNCTIONS. IF KEYLOCK BROKEN YOU WONT BEABLE TO TURN IGNITION KEY OR GET CAR OUT OF PARK.

Mar 26, 2011 | 1999 Oldsmobile Alero

1 Answer

How do you replace the ignition key switch for a '96 chevy diesel 1 ton 4wd pickup truck?


Ignition Switch Removal & Installation To Remove:
  1. Remove the steering column trim covers.
  2. Remove the wire harness from the retainers as needed.
  3. Slide the 2 connectors of the multifunction switch assembly out from the bulk head connector.
  4. Detach the key alarm connector from the lock assembly.
  5. Remove the ignition switch mounting screws and the ignition switch from the steering column.
Ignition switch removal/installation gm-08-00-1141.gif

To Install:
  1. Install the ignition switch on the lock module.
    • Tighten the screws to 42 lb in (4.7 Nm).
  2. Install the key alarm connector on the lock module.
  3. Slide the turn signal and multifunction switch connectors into the bulkhead connector.
  4. Install the harness in the original retainers.
  5. Install the steering column trim covers.
---
Ignition Lock Cylinder Removal & Installation To Remove:
  1. Disconnect the negative cable from the battery.
  2. Disable the supplemental inflatable restraint (SIR) system.
  3. Remove the steering column trim covers.
  4. Turn the ignition lock cylinder to the run position.
  5. Using an awl with a bent tip, insert the tip into the access hole of the ignition lock cylinder.
  6. Turn the lock cylinder to start and push down and hold the lock cylinder retaining pin.
  7. Release the lock cylinder to the run position and withdraw the cylinder from the steering column.
Ignition lock cylinder removal gm-08-00-1139.gif

To Install:
  1. Align the slot in the steering column to the tab on the lock cylinder and install the lock cylinder until it locks in place.
  2. Install the steering column trim covers
  3. Connect the negative cable to the battery
  4. Check for correct operation
prev.gif next.gif

Oct 08, 2010 | Chevrolet 3500 Cars & Trucks

1 Answer

How to replace the ignition on a 1991 oldsmobile cutlass cierra


If you mean the ignition lock cylinder:

Ignition Lock Cylinder CAUTION
If the car is equipped with an air bag, do not service the steering column or dashboard components. Extreme danger of air bag deployment exists even with the battery removed! Serious injury could occur. REMOVAL & INSTALLATION Without Air Bag
  1. Place the ignition switch in the RUN position.
  2. Remove the lockplate, turn signal switch and buzzer switch.
  3. Remove the screw and lock cylinder. NOTE: If the screw is dropped on removal, it could fall into the column, requiring complete disassembly to retrieve the screw. To install:
  4. Rotate the cylinder clockwise to align cylinder key with the keyway in the housing.
  5. Push the lock all the way in.
  6. Install the screw. Tighten the screw to 14 inch lbs. (2 Nm) for adjustable columns and 25 inch lbs. (3 Nm) for standard columns.
With Air Bag CAUTION
Before proceeding, refer to Section 6 for information on disabling and enabling the SIR (air bag) system; otherwise, serious injury could occur.
  1. Turn the steering wheel so the vehicles wheels are pointed straight ahead.
  2. Place the ignition switch into the LOCK position to prevent undercentering of the coil assembly.
  3. Disable the SIR system. Disconnect the negative battery cable.
  4. Remove the coil assembly retaining ring, then disconnect the inflatable restraint coil assembly. Let the switch hang freely if removal is not needed. To remove the coil assembly proceed.
  5. Remove the wave washer, then the shaft retaining lock ring with tool J-23653-SIR to push down on the shaft lock. Dispose of the ring, it is not reusable. Fig. 1: Special tool J-23653-SIR or equivalent is required for pushing down the shaft lock to remove the shaft ring 86818085.gif
  6. Remove the shaft lock, then disconnect the canceling cam assembly.
  7. Remove the upper bearing spring, race seat and race.
  8. Position the turn signal to the right turn (up) position.
  9. Remove the multi-function lever and hazard knob assembly. Unfasten the round washer head screw and signal switch arm, along with the turn signal switch screws.
  10. Remove the turn signal switch assembly by unfastening the connector from the bulkhead connector. Gently pull on the harness through the column and disconnect.
  11. Make sure the coil assembly does not become uncentered, this could happen if the centering spring is pushed down letting the hub rotate while the coil is removed from the steering column.
  12. Remove the inflatable restraint coil assembly with the wiring harness from the column assembly.
  13. Remove the wire protector, then attach a length of mechanics wire to the coil terminal connector to aid in reassembly. Then gently pull the wire through the column.
  14. Remove the key from the steering column lock cylinder set, then remove the buzzer switch assembly.
  15. Reinsert the key into the lock cylinder, turn it to the LOCK position.
  16. Remove the lock retaining screw, then the cylinder. To install: NOTE: Make sure all fasteners are securely seated before applying the necessary torque. If you fail to do so, component damage or malfunctioning of the steering column may occur.
  17. Install the lock cylinder assembly, insert the retaining screw, then tighten to 22 inch lbs. (2.5 Nm).
  18. Insert the key into the lock cylinder. Install the buzzer switch assembly. Turn the key to the LOCK position.
  19. Install the turn signal switch assembly wiring harness through the column, let the switch hang freely. Connect the wiring to the bulkhead.
  20. Insert the coil assembly wiring harness through the column letting the coil hang freely. Attach the turn signal assembly with the binding head screws. Tighten the screws to 30 inch lbs. (3 Nm).
  21. Attach the signal switch arm with the round washer head screw, tighten the screw to 20 inch lbs. (2 Nm).
  22. Install the hazard knob assembly and the multi-function lever.
  23. Install the inner race, upper bearing race seat and spring. Attach the turn signal cancelling cam assembly, apply grease for lubrication.
  24. Replace the shaft lock and install a new shaft lock retaining ring. Use tool J-23653–SIR or equivalent to push down on the shaft lock. The ring must be firmly seated in the groove on the shaft. NOTE: Set the steering shaft so that the block tooth on the race and upper shaft is at the 12 o'clock position. The wheel on the car should be straight ahead. Set the ignition switch to the LOCK position, as this will ensure no damage to the coil assembly.
  25. Install the wave washer, then attach the coil assembly, make sure it is centered correctly. Fig. 2: Centering the coil assembly is important in assembling the column assembly 86818086.gif

  26. Attach the coil assembly retaining ring, the ring must be firmly seated in the groove on the shaft.
  27. Gently pull the lower coil assembly, turn signal, and pivot (pulse) wires to remove any kinks that may be inside the steering column assembly. If you fail to do this you can damage the wiring.
  28. Complete assembling the steering column assembly.
  29. Attach the negative battery cable.
  30. Check the functions of the turn signal, make sure it cancels when turned on and the steering wheel is turned.
  31. Enable the SIR system. prev.gif next.gif

Aug 01, 2010 | 1991 Oldsmobile Cutlass Ciera

1 Answer

Install a Ignition lock cylinder 1997 Pontiac Grand Am


  • Ignition Removal Instructions
  • Disconnect the negative battery cable from the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
  • Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle or Steering Column Trim Covers - Disassemble - Off Vehicle .
  • Put the key in the steering column lock cylinder set (1).

  • Turn the key to the "START" position.
  • Install a 1/16 allen wrench (2) into the hole on top of the lock module assembly in order to release the steering column lock cylinderset retaining pin.
  • Turn the steering column lock cylinder set (1) into the "RUN" position.
  • Pull the steering column lock cylinder set (1) out from the lock module assembly.
  • Remove the key from the steering column lock cylinder set (1).

19eb1ff.png


  • Installation Instructions
Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
  • Insert the key into the steering column lock cylinder set (1).
  • LIne up the locking tab (2) and the positioning tab (3) of the steering column lock cylinder set with the locking tab slot (5) and the positioning tab slot (4) in the lock module assembly (6).
  • Push the steering column lock cylinder set (1) into the lock module assembly (6).
  • Rotate the steering column lock cylinder set (1) in the lock module assembly (6) into all positions.
  • Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble - Off Vehicle or Steering Column Trim Covers - Assemble - Off Vehicle
  • Remove the ignition key from the lock cylinder set (1).
  • Connect the negative battery cable to the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical

d612a25.png

I hope this helps and good luck.
Please remember to vote 962e1fb.jpg and leave a testimonial. Thanks.

Nov 02, 2009 | 1997 Pontiac Grand Am

1 Answer

How to remove? Switch continues to spin. Column intact. Do I have to remove the steering wheel or can the switch be pulled out and replaced?


Ignition Lock Cylinder REMOVAL & INSTALLATION With Key
  1. Disconnect the battery ground.
  2. On tilt columns, remove the upper extension shroud by unsnapping the shroud from the retaining clip at the 9 o'clock position.
  3. Remove the trim shroud halves.
  4. Unplug the wire connector at the key warning switch.
  5. Place the shift lever in PARK and turn the key to ON .
  6. Place a 1⁄8 in. (3mm) wire pin in the hole in the casting surrounding the lock cylinder and depress the retaining pin while pulling out on the cylinder.
  7. When installing the cylinder, turn the lock cylinder to the RUN position and depress the retaining pin, then insert the lock cylinder into its housing in the flange casting. Assure that the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will allow the cylinder retaining pin to extend into the cylinder cast housing hole.
  8. The remainder of installation is the reverse of removal.
Non-Functioning Cylinder or No Key Available FIXED COLUMNS
  1. Disconnect the battery ground.
  2. Remove the steering wheel.
  3. Remove the turn signal lever.
  4. Remove the column trim shrouds.
  5. Unbolt the steering column and lower it carefully.
  6. Remove the ignition switch and warning buzzer and pin the switch in the LOCK position.
  7. Remove the turn signal switch.
  8. Remove the snapring and T-bolt nuts that retain the flange casting to the column outer tube.
  9. Remove the flange casting, upper shaft bearing, lock cylinder, ignition switch actuator and the actuator rod by pulling the entire assembly over the end of the steering column shaft.
  10. Remove the lock actuator insert, the T-bolts and the automatic transmission indicator insert, or, with manual transmissions, the key release lever.
  11. Upon reassembly, the following parts must be replaced with new parts:
    • Flange
    • Lock cylinder assembly
    • Steering column lock gear
    • Steering column lock bearing
    • Steering column upper bearing retainer
    • Lock actuator assembly
  12. Assembly is a reversal of the disassembly procedure. It is best to install a new upper bearing. Check that the truck starts only in PARK and NEUTRAL.

Jul 13, 2009 | 1989 Ford F 250

2 Answers

96 ford windstar ignition probs


the ignition switch is the electrical part behind the lock cylinder where the key goes in.

Ignition Switch Lock Cylinder
Lock Cylinder Functional
Removal
  1. The following procedure applies to vehicles that have a functional ignition switch lock cylinder (11582) and keys. If the key numbers are known, the correct key can be made. Disconnect the battery ground cable (14301). For additional information, refer to Section 14-01 .
  1. Turn the ignition switch lock cylinder to the RUN position.
  1. Place a 3.17-mm (1/8-inch) diameter wire pin or small drift punch in the hole in the steering column shroud under the ignition switch lock cylinder. Depress the retaining pin while pulling out on the ignition switch lock cylinder to remove it from the housing of the steering column.
Installation
  1. Install the ignition switch lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the ignition switch lock cylinder into the steering column housing. Make sure the ignition switch lock cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the retaining pin of the ignition switch lock cylinder to extend into the hole of the steering column.
  1. Using the key, rotate the ignition switch lock cylinder to make sure of correct mechanical operation in all positions.
  1. Connect the battery ground cable.
-------------------------------------------------------------------------------------
Ignition Switch Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove the upper steering column shroud (3530) by removing the four or five self-tapping screws. Remove key release lever (3F527) (if equipped).
  1. Remove lower steering column shroud.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.


71f4c5f.gif


Item Part Number Description 1 11572 Ignition Switch 2 — Ignition Switch Lock Cylinder Housing 3 — Slot in Lock/Column Assembly A — (Part of 11572) Pin B — Alignment Mark
Installation
NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

  1. Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Check to make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Refer to Section 14-01 .
  1. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install upper steering column shroud.
  1. Install the lower steering column shroud and key release lever (if equipped).

Feb 27, 2009 | 1996 Ford Windstar

Not finding what you are looking for?
1992 Dodge Dynasty Logo

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...