Question about 2005 Pontiac Grand Prix

Open Question

2005 pontiac grand prix has key stuck in ignition and wont realease it. how do i remove the key? my name is V'Andre

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

PyroPCMan
  • 405 Answers

SOURCE: diagram on a pontiac grand prix

Ignition Switch GM Century/Lumina/Grand Prix/Intrigue 1997-2000 The vehicles covered by this guide use one of two types of ignition switches:

  • A mechanical key and lock cylinder built into the steering column, that works a pull rod to actuate the separate electrical portion of the ignition switch mounted further down the steering column. For more information and replacement procedures on this type of switch, please see .
  • An instrument panel-mounted ignition switch is also used on some W-Body vehicles. To service this switch, the radio, heater & A/C control panel and the instrument cluster must be removed. All of these procedures are found elsewhere in this section.
REMOVAL & INSTALLATION
Instrument Panel-Mounted Ignition Switch
WARNING You must perform the Body Control Module (BCM) theft deterrent relearn procedure after replacement of the ignition lock cylinder. Failure to perform this relearn procedure means the BCM will not function properly. This means the vehicle will not be theft protected by the Passlock system and the engine may not crank or start. GM recommends that this procedure be performed with their Tech 2® or equivalent scan tool. An alternate relearn procedure is given at the end of this procedure.
  1. Disconnect the negative battery cable.
  2. Remove the radio assembly following the procedures found in this section.
  3. Remove the heater & A/C control head assembly following the procedures found in this section.
  4. Remove the instrument cluster assembly following the procedures found in this section.
  5. Detach the electrical connectors from the ignition switch.
  6. Insert the key and turn the ignition switch lock cylinder to the ACC position.
  7. Depress the transaxle park/lock cable retainer to release, then pull to remove the cable from the ignition switch.
NOTE You must perform the Body Control Module theft deterrent relearn procedure after replacement of the ignition lock cylinder.
  1. If it is necessary to remove the ignition lock cylinder from the ignition switch (theft damage, etc.), use the following procedure:
    1. Insert the key and turn the ignition switch lock cylinder to the ON position.
    2. Using a small flat-bladed tool, depress and hold the lock cylinder retaining tab.
    3. Using the key as an aid, pull to remove the ignition switch lock cylinder from the switch.
    4. Remove the key from the lock cylinder.
    5. Carefully pull to release the ignition switch bezel from the ignition switch lock cylinder.
  2. Remove the ignition switch bracket bolts and remove the ignition switch through the instrument panel cluster opening.
  3. Remove the bolts retaining the ignition switch to the bracket and remove the bracket.
0900c15280090fea.jpgRemoving an instrument panel-mounted ignition switch assembly—1998 Oldsmobile Intrigue shown, others similar To install:
  1. Install the ignition switch to its bracket and install the bolts. Install the ignition switch into position through the instrument panel cluster opening and install the bracket retaining bolts.
  2. If removed, install the ignition switch lock cylinder to the ignition switch using the following procedure:
    1. Recode the lock cylinder, if necessary.
    2. Align the ignition switch bezel to the tabs on the ignition switch lock cylinder and carefully press to secure in place.
    3. Insert the key and turn the ignition switch lock cylinder to the ON position.
    4. Align the ignition switch lock cylinder to the ignition switch, then press into place.
  3. Turn the key to the ACC position. Align and press into place the transaxle park/lock cable to the ignition switch. Remove the key from the switch.
  4. Attach the electrical connectors to the ignition switch.
  5. Install the instrument cluster using the procedures found in this section.
  6. Install the heater & A/C control panel using the procedures found in this section.
  7. Install the radio assembly using the procedures found in this section.
  8. Connect the negative battery cable.
  9. If the lock cylinder was removed, perform the BCM Programming/RPO Configuration procedure.
THEFT DETERENT RE-LEARN—WITHOUT TECH 1®SCAN TOOL
This procedure takes approximately 30 minutes. Make sure the battery is fully charged before proceeding.
  1. Turn the ignition switch to the OFF position.
  2. Turn the ignition switch all the way from the OFF to the START position, then leave it in the ON position. The engine will not crank.
  3. The SECURITY light should come on and stay on for at lease ten minutes.
  4. Turn the ignition switch to the OFF position for five seconds.
  5. Repeat Steps 2, 3 and 4 again for a second time.
  6. Repeat Steps 2, 3 and 4 again for a third time.
  7. Turn the ignition switch to the OFF position.
  8. Turn the ignition switch all the way to the START position. The engine should now start.

Posted on Sep 09, 2008

  • 87 Answers

SOURCE: key stuck in ignition of 2005 pontiac grand prix

Check for power and ground at the break, transmission, interlock switch located at the gear shift - if you have power and ground interlock is faulty - replace interlock switch. If no power and ground - check circuit continuity.

Posted on Aug 02, 2009

motor1258
  • 6674 Answers

SOURCE: spark plug gap for 2005 pontiac grand prix gt 3.8

.060 thousandths of an inch.

Posted on Nov 19, 2009

Molson02536
  • 3854 Answers

SOURCE: 2005 pontiac grand prix, code p0641 came on. What

DTC P0641 The powertrain control module (PCM) provides a 5-volt reference to the following sensors:

The throttle position (TP) sensor 1
The accelerator pedal position (APP) sensor 2
The engine cooling fan speed sensor
The AC pressure sensor
The fuel tank pressure (FTP) sensor
The oil pressure sensor (OPS)
The PCM monitors voltage on the 5-volt reference circuit. If the voltage is higher or lower than required, DTC P0641 will set.

Conditions for Setting the DTC
The PCM detects a voltage that is higher or lower than required on the 5-volt reference circuit. The above condition is present for 1 second. Action Taken When the DTC Sets The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame/Failure Records.
Conditions for Clearing the MIL/DTC The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. A current DTC, Last Test Failed, clears when the diagnostic runs and passes. A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. Clear the MIL and the DTC with a scan tool.

Yes i can be dangerous, depending which issues mentioned above has triggered the code such as a faulty gas peddle position sensor. the code can also cause a reduced engine power to activate.

Thank you for using Fixya and best advice is to have the dealer address these issues. A tech 2 scanner would be needed to address the P0641 DTC code.

Posted on Mar 19, 2010

Testimonial: "Thank you for your detailed, easy to understand and very quick response!"

  • 55 Answers

SOURCE: 1997 pontiac grand prix key won t turn ignition

well does the key go in does it turn to the start pos? if the dash dost power up its because the switch is bad if it will power up but not start it can be becuse of the resitor chip depends on what is going on if you cant get power its becuse of the switch

Posted on May 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key stuck ignition wont


This usually happens if your steering wheel is in the rightmost or the leftmost position. Try wiggling the steering wheel when pulling out the key.

Jul 20, 2014 | 2000 Pontiac Grand Prix

1 Answer

Key is stuck in the ignition


Remove the cap under ignition push button i use a toothpick key wil come out

Jan 27, 2014 | 2005 Pontiac Grand Prix

1 Answer

1999 grand prix key wont come out of ignition


Have you tried wiggling the steering wheel while trying to remove the key, also wiggle shifter around.

Jun 13, 2012 | Pontiac Cars & Trucks

1 Answer

Key gets stuck from removal Problem with the Pontiac Grand Prix 2005 Grand Prix Key gets stuck from removal of tumbler Liquid wrench works for a while .Iv tried resetting security settings to no avail .Is...


Yes, this is a common problem. No, there is no recall. Recalls are only for safety issues that can cause bodily harm.

This is caused by wear in both the key and the tumbler. Usually, it is best to have a new key cut at the dealer using the VIN to get the proper key code. Sometimes this is all you have to do. (I would try this first) Most of the time however, it also requires replacement of the lock cylinder as well. GM (AC Delco) lock cylinder kits come with an assortment of tumblers so the lock cylinder can be coded to fit your new key.

Jan 05, 2011 | 2005 Pontiac Grand Prix

1 Answer

1992 pontiac grand prix le interior lights and key buzzer wont go


inside the steering column locate the ignition remove wire to reveal screw to remove ignition that wire is what controls the buzzer and light itthe wire probrally wasnt in place correctly wich caused your problem

Apr 27, 2009 | 1992 Pontiac Grand Prix

1 Answer

2005 grand prix -- trunk lid won't open


If you will turn the ignition on, press & hold the door lock release button to the left . . . . viola!

Apr 17, 2009 | 2005 Pontiac Grand Prix

1 Answer

Can't remove key


Sounds and seems like the ignition is getting stuck, and should be replaced.

Feb 06, 2009 | 2002 Pontiac Grand Prix

1 Answer

Key stuck in ignition


you need to replace your key ignition

Jan 10, 2009 | 1992 Pontiac Grand Prix

Not finding what you are looking for?
2005 Pontiac Grand Prix Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...