Question about Chrysler Sebring

1 Answer

99 Chrysler sebring conv. driving or sitting at light car stalls out dies, wait 3 to 5 minutes starts up but will die again sometimes in a few miles sometimes not. Have had fuel filter, fuel pump, rotar, and 02 sensor replace. I just read about the #8 fuse?? I also read about the crankshaft sensor but the shop they checked and it's fine I'm not so sure, Any help I would appreciate

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 766 Answers

The crankshaft sensor would fit with the symptoms. Often the voltage output from faulty sensors declines with temperature rise so the temperature at which your CKP was checked over is critical. How to check? First check that the electrical connection is clean and secure; dirt or corrosion can impair an otherwise healthy CKP signal from getting through. If the CKP suffers from a drop in voltage associated with heat increase this can only be detectable with a voltmeter or oscilloscope with a graphical display; an analogue display voltmeter might just be able to show needle fluctuations due to voltage variation output. There are two types of CKP:-

2 pin socket (magnetic - sine wave output). One pin is 'ground' the other is 'signal'. A voltmeter set to 2 volts AC (note well) should measure a signal in the 0.2 to 2 volts range on the 'signal' pin.

3 pin socket (Hall effect, magneto - square wave form output). One pin is 'reference' (5volts), one pin is 'ground' and the third pin is 'signal'. A DC voltage (again note well) should be detectable in the 0.5 to 1.5 volt range from the 'signal' pin.

It is important that the voltage measurement take place at start up when the engine is cold and again, 20 minutes later, when the engine has fully warmed up to operating temperature. If there is a marked decline in voltage output between hot and cold, replace the CKP. If all looks well apply this diagnostic to the cam position sensor CMP (it works in exactly the same way)

Posted on Nov 15, 2010

  • li dee Dec 15, 2011

    Still nt running

  • li dee Dec 15, 2011

    Have 99 Chrysler Sebring water hosed busted an bout anothere one next day shot off while driven ..please help me

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 Volvo V70 seems to stall and vaporlock, after running. The car shows an ETS light, which I understand to be the Electronic Throttle Sensor. It has shown this light for over a year, but has not given...


change your fuel filter ..your vehicle will run but your fuel pressure is weak ..also after this clean your fuel injectors by pouring injection cleaner in your gas ,,it will correct itself..Also ,,if none of what I stated works ,,Spark plugs and new spark plug wires needed ,,Lastly your fuel pump

Oct 23, 2013 | 1999 Volvo V70

1 Answer

2004 Crossfire just dies (rarely and randomly) when driving or sitting at a light. Check engine light is on; low coolant light is also on... intermittently. Had it checked at a shop; no codes were found...


the coolant light won't cause it to stall more likely to be a crank shaft sensor possibly only way to find out though is to replace it and see what happens sometimes these things don't throw up codes and would need the scan tool to be on the car when it stalls and won't start again the crank sensor cools down then will work again

Apr 08, 2013 | Chrysler Cars & Trucks

1 Answer

Car dies while driving


HI. this is a fuel filter issue. would have it replaced asap if possible. you should also, purchase a fuel additive to flush out the fuel injectors and fuel lines as well. Sea foam is a very good fuel system additive.

Due to the fact that this car is a 1999 model, i would change the fuel pump as well. this is good preventive maintenance.

One more thing, if you have not had a full scale tune up recently or, in the last 10,000 miles, i suggest scheduling one soon.

Jun 20, 2009 | 1999 Chrysler Sebring

1 Answer

1998 Sebring Conv 2.5 L JX Starts but dies immediately when cold


sounds like a possiable coolant temp reading -40 degrees have it checked

Apr 25, 2009 | 1998 Chrysler Sebring

1 Answer

1996 chrysler sebring 2.5l v6 dies randomly


it sounds like it the crank pos. sensor

Apr 04, 2009 | 1996 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...