Question about 1995 Nissan Pathfinder

1 Answer

Don't remeaber how the belts go back on - 1995 Nissan Pathfinder

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

They only go one way. So just try putting on the first on and work your way forward.

Posted on Nov 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a routing diagram for the serpentine belt


you don`t say what year this is. most cars as far back as late 90`s still have the decal under the hood somewhere that shows the belt routing. the auto parts store may show a belt routing for your car as well.

Apr 19, 2015 | Cars & Trucks

1 Answer

Tighten Serpentine Belt


Technically, you don\'t. The tensioner pulley keeps the belt tight. If you took the belt off and put it back on, and now it is not tight, it may be on one of the pulleys wrong.

May 12, 2013 | Cars & Trucks

1 Answer

Cant put serpintine belt on


You don't take anything off

You just put a long 1/2" ratchet in the hole on
the tensioner & Pull against the spring tension until
you have the belt over the final pulley

Oct 12, 2012 | 2000 Buick LeSabre

1 Answer

My crakshaft will not turn after doing a water pump


I personally do not know the model but due to my experience I might help. If the water pump is in the timing belt area,means that you removed the timing belt. Did you put the timing belt in the correct position or you just fit it back on? If you just put it back on surely you are out of timing and might Piston is touching the Valve.Don't try to start it ,Just call an expert to help.

Aug 20, 2012 | Chrysler Sebring Cars & Trucks

1 Answer

I put on a new fan belt and it makes a squeaking noise after just a few months....why is this......the engine is a 4.3 L G20 chevy van 1994 without AC


Could be a pulley making the noise. Could be your choice of belts. I have had good luck with the Goodyear Gator Back belts. And I don't care if someone says their store brand is made by Goodyear. They may be what Goodyear throws away and the store goes dumpster diving for them.

Its harder to do on a van but what you can try if you don't have an automotive stethescope is hold a piece of hose to your ear and the other end around the pulleys to help you narrow down where the noise comes from..

Sep 09, 2011 | Chevrolet G20 Cars & Trucks

2 Answers

Squeaking sound from fan belt


  • Take a can of brake clean and spray it on the belt while it is rotating. If the sound goes away for good it was a dirty or wet belt. If the sound goes away and come back it is more than likely a bad belt. Remove the belt and turn all the pulleys to see if they are spinning free. a stuck pulley can cause a belt to squeal too. If a pulley should catch a bit then perhaps the pulley could be part of the issue as well. Should all pulleys check good then put a new belt on. Don't forget to check the tension pulley for weak springs.

Regards, Tony

May 10, 2011 | Ford Mustang Cars & Trucks

2 Answers

Timing belt broke . installed new one ,now auto back fire's. won't start


Did you get it timed correctly? You don't just replace them like a fan belt, there is a procedure and marks that you line up. Your engine may be a non-interference or interference which means that if your timing belt breaks your pistons may hit your valves and cause major engine damage. Non-interference means that when the belt breaks it won't interfere and cause damage. Interference means that it will. I don't know what engine you have in your car but if you call a dealer and tell them what engine you have in your car they should be able to tell you if it is a non-interference or interference engine.

May 02, 2011 | 1999 Oldsmobile Alero

1 Answer

Which bolts on the altenator and power steering pump need to be loosened to release the belts on a 2003 Mazda Protege?


I don`t know that there is a bolt to loosen the belt tension.There should be a automatic tensioner that you pull back and hold to remove the belt.

Oct 16, 2009 | 2003 Mazda Protege

2 Answers

Need a timing belt diagram


if the timing belt has no teeth on it your in alota trouble, its a cog belt should have alot deep teeth. the tesioner in underneth the plastic cover for the belt and its automatic, adjusts w a spring loaded arm and is dampened hydrauicly. if you need a diagram go to autozone or gates belts company for a diagram

Aug 24, 2009 | 2002 Ford ZX2

3 Answers

When should I replace timing belt


it is recommended that u replace at 60,000 miles

Jan 06, 2009 | 2002 Suzuki Esteem

Not finding what you are looking for?
1995 Nissan Pathfinder Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...