Question about 1995 Isuzu Rodeo

2 Answers

95 rodeo coolant problems

I have a 95 isuzu rodeo v6 3.2L 4x4 ..i just replaced the oil cooling hoses(upper and lower)..now when the engine warms and the thermostat opens coolant appears to be leaking from between the motor and the transmission.. i dont know what this could be.. any one have any suggestions/// pllease send them to osamfrky@aol.com..... thanx

Posted by on

2 Answers

Hi
aj like
shum













Posted on Jun 19, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,966 Answers

Hi,

Recheck the connection of the upper hose that leads to the engine side with particular attention to the lip of the metal tube. In most instances, it would be the hos not pushed in properly or a clamp that is not tightened wholly encompassing the hose. Additionally, you may want to check the thermostat housing for any cracks/leaks.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Posted on Jun 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the radiator on a 2003 Buick Lesabre


3.8L Engine

  1. Drain the engine coolant.
  2. Remove the upper radiator seal.
  3. Remove the upper tie bar.
  4. Disconnect the coolant overflow hose from the radiator.
  5. Plug the coolant overflow hose.
  6. Disconnect the upper and lower radiator hoses.
  7. Remove the transaxle oil cooler pipe bracket bolt from the lower tie bar.
  8. Remove the cooling fans.
  9. Slide the plastic cap off the transaxle oil cooler pipe quick connect fittings.
  10. Disconnect the upper and lower transaxle oil cooler pipes from the radiator.
  11. Remove the A/C condenser mounting bolts.
  12. Separate the condenser from the radiator.
  13. Lift the radiator up and out of the vehicle.
To install:
  1. Install the radiator to the vehicle. Place the bottom of the radiator in the lower pads.
  2. Install the condenser to the radiator.
  3. Install the A/C condenser mounting bolts and tighten to 115 inch lbs. (13 Nm).
  4. Push the upper and lower transaxle oil cooler pipes into the radiator quick connect fittings, until a "click" is heard.
  5. Tug gently on the cooler pipes to ensure proper retention.
  6. Slide the plastic caps (1) over the quick connect joints.
  7. Install the cooling fans.
  8. Install the transaxle oil cooler pipe bracket bolt to the lower tie bar and tighten to 89 inch lbs. (10 Nm).
  9. Install the upper and lower radiator hoses.
  10. Connect the coolant recovery hose to the radiator neck.
  11. Install the upper tie bar.
  12. Install the upper radiator seal.
  13. Fill the cooling system.
  14. Inspect the transmission oil level.

Nov 02, 2015 | Buick Cars & Trucks

1 Answer

I need a diagram for a 95 isuzu rodeo 2.6L cooling system


You need to pinpoint the problem by measuring he temperatures of the system.

1. If the engine is 190f and the upper hose is warm, but the lower hose is cold, you either have a thermostat problem, or a bad water pump.

2. if both the hoses are as hot as the engine then you have either a bad fan (is it running at normal speeds?) or a bad radiator.

3. When cold, leave the cap off, is it full? do you see continuous bubble as it runs? when you start it does coolant spray out (from a cold start) if so then you could have a bad head gasket.

May 18, 2014 | Isuzu Rodeo Cars & Trucks

1 Answer

How to change a radiator


1988–91 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 7: Cooling system components — 1988–91 engines 86833085.gif
1992–95 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 8: Cooling system components — 1992–95 engines 86833086.gif
prev.gif next.gif

Aug 27, 2010 | 1991 Honda Civic

2 Answers

How do I replace a radiator on a 2002 maxima


Nissan Car 350Z & Maxima 1999-06 Radiator - Removal & Installation

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Coolant reservoir tank and bracket Upper mounting bracket Upper radiator hose Oil cooler lines, if equipped Lower radiator hose Cooling fan and condenser fan Fan motors and shields Radiator

To install:
  1. Install or connect the following:
    Radiator Fan motors and shields Cooling and condenser fans and torque the bolts to 44 inch lbs. (5 Nm) Lower radiator hose Oil cooler lines, if equipped Upper radiator hose Upper mounting bracket Coolant reservoir tank and bracket and torque the bolt to 44 inch lbs. (5 Nm) Negative battery cable
  2. Fill the cooling system to the proper level.
  3. Start the vehicle, check for leaks and repair if necessary.
WARNING Do not remove radiator cap when engine is hot. Serious burns could occur from high-pressure engine coolant escaping from radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter of a turn to release built-up pressure. Carefully remove radiator cap by turning it all the way.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Coolant reservoir tank and bracket Upper mounting bracket Upper radiator hose Oil cooler lines, if equipped Lower radiator hose Cooling fan and condenser fan Fan motors and shields Radiator
To install:
  1. Install or connect the following:
    Radiator Fan motors and shields Cooling and condenser fans and torque the bolts to 44 inch lbs. (5 Nm) Lower radiator hose Oil cooler lines, if equipped Upper radiator hose Upper mounting bracket Coolant reservoir tank and bracket and torque the bolt to 44 inch lbs. (5 Nm) Negative battery cable

  2. Fill the cooling system to the proper level.
  3. Start the vehicle, check for leaks and repair if necessary.
WARNING Do not remove radiator cap when engine is hot. Serious burns could occur from high-pressure engine coolant escaping from radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter of a turn to release built-up pressure. Carefully remove radiator cap by turning it all the way.
240ef5f.jpg

Fig. Exploded view of radiator and components
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    CAUTION Do not damage or scratch the A/C condenser and radiator core while removing.
    CAUTION Because A/C condenser is onto the front-lower portion of radiator, moving to rear direction should be at minimum.
    Negative battery cable Engine cover Air duct and air cleaner case assembly Bracket mounting bolt for anchoring A/C piping Reservoir tank and bracket Upper and lower radiator hoses Radiator cooling fan assembly On A/T models, A/T fluid cooler hoses. Plug hoses to avoid leakage Cover, then two A/C condensing mounting bolts located in the upper part of the radiator Rotate two radiator upper mount brackets 90 degrees in the direction shown in the illustration and remove fce8147.jpg

    Fig. Removing A/C condensing mounting bolts

    d3c8f50.jpg

    Fig. Rotating radiator upper mount brackets 90 degrees

    edb9f67.jpg

    Fig. Removing radiator
  4. Remove the radiator by performing the following:
    CAUTION Lifting A/C condenser should be minimum to prevent a load to A/C piping.
    With lifting and pulling radiator in a rear direction, disassemble lower mount from radiator core support center. Lift A/C condenser up and remove radiator after disengaging the fitting as front-bottom surface After removing radiator, put A/C condenser on radiator core support center to prevent a load to A/C piping, and temporarily fix it with rope or similar means

To install:
  1. To install, reverse removal procedure.
  2. Check radiator cap for any leaks.
  3. Start and warm up engine. Check for engine coolant leaks and A/T fluid leaks.

Hope this help (remember comment and rated this).

May 12, 2010 | 2002 Nissan Maxima

1 Answer

I need to know the correct name of cooling system hoses


You have the upper and lower radiator hoses, then you have coolant bypass hoses, then you have heater hoses.

Sep 26, 2009 | 1998 Isuzu Rodeo

3 Answers

Isuzu rodeo leaking coolant from engine


with my experiance on these engines it's usually the upper outlet hoses running from the heads into a t then into the upper radiator hose they are pain to replace but 3 out of 3 of my v6 isuzu's have had the same problem you'll have to pull off the theromstat and the coil pack the hoses are very small and run from the end of the heads one on each into a t then into the radiator hose just under the housing

Apr 27, 2009 | Isuzu Rodeo Cars & Trucks

1 Answer

95 rodeo coolant problems


it could be leaking somewere else , get your cooling system pressure tested at a shop

Mar 07, 2009 | 1995 Isuzu Trooper

1 Answer

Coolant still leaking from my 1996 Isuzu Rodeo.


There is a plastic heater pipe junction behind the inlet manifold against the fire wall that could be brittle and leaking.

Nov 16, 2008 | 1995 Isuzu Rodeo

1 Answer

RADIATOR REPLACEMENT


  • At the time of installation, please refer to the following items.
  • Start the engine, and check for coolant and A/T fluid leaks.
  • Check the A/T fluid level.
  1. Drain engine coolant.
  2. Canada: Disconnect relay block (for daytime running light system) from battery hold-down clamp.
  3. Disconnect upper radiator hose from radiator.
  4. Disconnect lower radiator hose from water inlet pipe.
  5. Disconnect A/T oil cooler hoses from oil cooler pipes.
  6. Disconnect No.1 and No.2 cooling fan connectors.
  7. Disconnect No.1 Engine Coolant Temperature (ECT) switch wire connector.

  8. Remove radiator and cooling fans assembly.
    1. Remove the 2 bolts and 2 upper supports. Torque: 12.8 Nm (9 ft. lbs.)
    2. Lift out the radiator, and remove the radiator and cooling fans assembly.
    3. Remove the 2 lower supports.
  1. Remove A/T Oil cooler hoses from radiator.
  2. Remove lower radiator hose from radiator.
  3. Remove No.1 ECT switch.

  4. Remove No.1 cooling fan from radiator. Remove the 2 bolts and cooling fan. Torque: 5.0 Nm (44 inch lbs.)
  5. Remove No.2 cooling fan from radiator. Remove the 3 bolts and cooling fan. Torque: 5.0 Nm (44 inch lbs.)
INSTALLATION
Installation is in the reverse order of removal.

Nov 06, 2008 | 1992 Lexus Es 300

Not finding what you are looking for?
1995 Isuzu Rodeo Logo

Related Topics:

402 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...