Question about 2003 Ford Focus

1 Answer

Ford focus 2003 cl heater problem heator only works in position 4.how do i fix it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Replace the blower resistor. Its up under the dash on passenger side, beside the blower motor.

Posted on Nov 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is 2003 ford focus camshafts position sensor


Camshaft Position Sensor
The camshaft position (CMP) sensor detects the position of the camshaft. The CMP sensor identifies when piston No. 1 is on its compression stroke. A signal is then sent to the powertrain control module (PCM) and used for synchronizing the firing of sequential fuel injectors. The Coil On Plug (COP) Ignition applications also use the CMP signal to select the proper ignition coil to fire. The input circuit to the PCM is referred to as the CMP input or circuit.
There are two types of CMP sensors: the three pin connector Hall-effect type sensor (Figure 25) and the two pin connector variable reluctance sensor

a452a319-2d08-4e59-9885-fe43b5fc7f61.gif

and next the location of 2003 ford focus camshafts position sensor
96d62950-03fc-4668-b3ad-dfa939f76b14.gif

Sep 13, 2014 | 2003 Ford Focus

1 Answer

Ford Focus CL 2003, Door open light keeps flashing, indicators either trip out or go double speed when door open light on.


At the door jam,check the condition of the pin switch. The switch may be cover with a boot.
Compare the condition of this pin switch to the working side.
Clean the general area and re-test.

Jan 19, 2014 | Ford Cars & Trucks

2 Answers

Ford focus 2003 CL 6000 cd rds e.o.n. keycode or serial number where can i find ?


the ford dealership should have the tools you need to remove the radio at a reasonable price, also if you have the VIN they may be able to give you the code you need.

Sep 01, 2012 | 2003 Ford Focus

1 Answer

I have a 1997 ford F150 4x4 king cab that has no heat. I have flushed the radiator, changed the heater core and flushed the heater hose. Still no heat.


Have any of you stopped to think that the Thermostadt may B bad especially after flushing the radiator replacing the heator cor Duh!!!!
Rplace the Thermostadt it will more then likley do the trick.
When the thermostadt goes out you will experiamce hot radiators no heat . ect.... first thing 95% of the people that experiance this replace the heator core first . no that you have elemanated the least obvious do the most

Oct 24, 2011 | 1997 Ford F150 Regular Cab

1 Answer

I need to reprogram the car door keypad on my 2003 Ford Focus.


Programming
When
Key(s) added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Fasten seat belts and close all doors. Turn ignition switch from position I to position II 4 times within 6 seconds. Switch ignition OFF. Programming mode activated for 10 seconds proceed as follows: Press and hold lock, unlock or boot release button Fig. 1 [1], [2] or [3]. Wait for acoustic signal (indicates correct programming). Repeat above procedure within 10 seconds to program remaining keys. To exit programming mode: Turn ignition switch to position III or wait 10 seconds. Keys can also be programmed using diagnostic equipment.
NOTE: A maximum of 4 keys can be programmed.

Feb 18, 2010 | 2003 Ford Focus

1 Answer

Heater fan only works on fastest speed


Your blower motor resistor has gone bad, it should be located next to your blower motor in the car, held in place with a couple of screws, remove it and replace it. The resistor is responsible for making the blower motor run at slower speeds than high or (4). Let me know if this helps.

Jun 16, 2009 | 2000 Ford Focus

1 Answer

96 Ford Galaxy Heator Fan not working


Check the Blower motor Resistor . It is located under the dashboard near the blower motor. It has a 4 wire plug and a couple of screws attaching the resistor in place.

Feb 18, 2009 | 2000 Ford Focus

1 Answer

No heating in my ford focus car .


Did you replace the fan the blows the air into the car or just the heater? It could simply be a blown fuse.

Dec 05, 2008 | 2005 Ford Focus

2 Answers

I have a 2006 ford tuarus,


you need to replace the blower motor resistor, the reason it only works on high is that position bypasses the resistor, it is located near the blower motor

Nov 29, 2008 | 2006 Ford Taurus

Not finding what you are looking for?
2003 Ford Focus Logo

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...