Question about 2002 Mitsubishi Diamante

1 Answer

My distibutor wires are off and i cant tell which wire goes where on the distributor, the wires are number but i can see where on the distributor they go.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mitsubishi Master
  • 17,970 Answers

I suggtes check this wiring diagram for 2002 Mitsubishi Diamante LS Sedan 3.5 liter SOHC V-6...

my distibutor wires are off - zjlimited_20.gif

Hope this helps (remember to arte and comment this answer).

Posted on Nov 15, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

New spark plugs, new spark plug wires, new distibutor, new distibutor cap, new coil, new coil wire still not getting any spark why?

I know you list a new distributor, but the pick up coil (inside the distributor) is what will trigger the coil for spark. Located under the rotor, it needs to be checked at the harness for voltage (key on) and measure resistance in the PU coil itself using an ohm meter. Check the harness for breaks or damage, there really is nothing else that might cause this unless you have a complete failure in your engine computer (located next to the battery).

Oct 04, 2011 | 1987 Plymouth Sundance

1 Answer

Where is the distibutor cap on a 1993 Jetta Wagon?

Hi, look on the engine block for the place where all the spark plug wires go, and you've find the distributor. Unsnap all clips and take off the distributor cap and suppressor shield, leaving the spark plug wires attached.

May 16, 2011 | Volkswagen Jetta Cars & Trucks

1 Answer

Why won't 1996 Toyota T100 won,t start after changing plus & distributor

OH no! okay something got disconnected is the rotor on now the coil is it attatch. okay now the distributor is the coil to distibutor wire in the middle of all wire okay now the firing orderwell you know what the firing should be right if it was off one or two it would of misfire so let go rotor installed coil ,wire didnt fall out okay. no connection fell out okay coil wire goes in the middle of rotor okay ready to start. Do you have gas and can you hear the pump? Let me know we will take it from here

Apr 22, 2011 | 1996 Toyota T100

2 Answers

2000 dodge durango 318 v8 quit running while driving.cranks but won't start or fire.

Check to see if there is any spark coming to the spark plugs from the distributor,if so change out your plugs, if not check from the coil to the distibutor, if so then change distibutor cap and button( if that still dossn't get it try the entire distributor), if not than check the hot wire going into the coil and if that is hot try replacing the coil but if not then i think you may have an electronic or wireing issue

Aug 11, 2010 | Dodge Durango Cars & Trucks

1 Answer

I just put a hei distibutor on a 66 283 v8 in my s10. now im trying to figure out how to and at what position to put the wires on the new cap.

Look and see if the manifold has numbers above the spark plugs some do and then see if the distributor cap has numbers on the top of it.

Sep 09, 2009 | Chevrolet S 10 Cars & Trucks

3 Answers

What order do i plug the spark plugs into the distributor on 1989 honda civic 1.5L

The plug wires are different lengths for different spark plugs. The best way to not get messed up is to do one wire at a time. Unplug old wire from distributor and plug, compare it to the new ones, find the new one that is the same length and replace. You don't want to get the wires mixed up. Hope this helped.

Jul 18, 2009 | 1989 Honda Civic

1 Answer

Repairing a distributor on a 1976 jeep wagoneer

check out should show you what you need to do. the air gap should be .008 in measured with a non metallic feeler guage.

Mar 27, 2009 | 1983 Jeep Cherokee

1 Answer

Need timing setting for 1998 Dodge Ram 1500

Put the number one piston at TDC (top dead center) Pull the cover off the distributor and check to see if the rotor is pointed at the number 1 plug wire. If not check to see if its directly accross from number 1 if so pull the distibutor out and turn the rotor button around 180 degrees. The distibutor can only go in 2 ways. Dead on the money or 180 degrees out. This info is assuming you havent replaced the timing chain or anything that effects factory time settings.

Mar 08, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

Oo kia sportage distributor cap

this car has two coils both of them are under the intake plentum they sit on numbers 2 and 4 cylinders and fire the other two by plug wires

Jan 17, 2009 | 2000 Kia Sportage

2 Answers

1987 GMC Jimmy Distributor cap and Rotor replacement

A diagram may not be needed as its a reasonably easy fix to do on your own.the distributor ca p will only fit on properly one way because at the base of the cap locaters can only fit the distributor if they line up.When doing the spark plug leads do them one at a time and if nessecary write or mark leads as 1,2 etc .The rotor can only fit on one way but put a mark on the distributor to show where the rotor was pointing when you took it off and if it still points there when the new one is fitted.When changing distributor cap and leads they have to go to the correct place.Pays to mark the outside of distributor cap where the locating bits are On the new and old one.Fit the new cap and rotor then take a spark plug lead and fit to new cap 1 at a time.You can tell by lining up the marks on the outside of the distributor cap when you hold them one on top of the other.Good luck

Oct 20, 2008 | 1987 GMC Jimmy

Not finding what you are looking for?
2002 Mitsubishi Diamante Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides