Abs module 1993 Nissan Maxima - Anti-Lock Brake Control Module (ABS) hi AvioriX Thank you to Fixya I am pratap looking for the 1993 Nissan Maxima GXE 4 DOOR Anti-Lock Brake Control Module (ABS) PART # 47600 96E00 (this number I got it from top of the unit, this unit has 4 cylinders having 3 electrical cables attached and my brake oil is leaking from this unit and every day I top up the brake fluid. I appreciate if I could get this part or guide me from where I could get it. thanks Pratap [email protected]

Anti-Lock Brake Control Module C176
Lower LF of engine compartment near cooling fan
The anti-lock brake control module is located below the brake pressure control valve block (2C266).

The light being on means the system has detected a problem in one or more sensors. The vibration is the ABS modulating the brakes to prevent skidding because it has detected a wheel that is locked up. That wheel is most likely the one sensor that is giving you the error.

Here's a link to your abs. Repair Guides Anti lock Brake System Hydraulic Anti lock Actuator...

its mountes on the abs pump

Having the vehicle checked for DTC'S - diagnostic trouble code's would be a good first step . ABS light on codes are stored . Suggest you take your vehicle to a qualified repair shop that has the knowledge an testing equipment to diagnose the problem properly .
Anti-Lock Brake System (ABS)
The 4-wheel, 4-channel anti-lock brake system (ABS) consists of the following components:

• ABS module
• Front wheel speed sensor
• Front wheel speed sensor ring (integral to the front wheel bearing)
• Hydraulic control unit (HCU)
• Rear wheel speed sensor
• Rear wheel speed sensor ring (integral to the rear halfshaft)
• Yellow ABS warning indicator
• As you can see here , it can set numerous
• DTC'S Why guess an replace parts that won't fix the problem .
• Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 ECU is Faulted ABS Module NOTE: If other DTCs are present, REPAIR them before installing a new component.
  CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is retrieved, INSTALL a new module. REFER to Anti-Lock Brake System (ABS) Module in this section. REPEAT the self-test. B1483 Brake Pedal Input Circuit Failure ABS Module Go To Pinpoint Test B . B1676 Battery Pack Voltage Out of Range ABS Module Go To Pinpoint Test C . B2477 Module Configuration Failure ABS Module CONFIGURE the ABS module. REFER to Section 418-01 . CLEAR the DTCs. REPEAT the self-test. If DTC B2477 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . REPEAT the self-test. B2734 Pedal Travel Sensor Supply Error ABS Module Go To Pinpoint Test M . B2736 Pedal Travel Sensor Circuit Fault ABS Module Go To Pinpoint Test M . B2737 Pedal Travel Sensor Jammed Error ABS Module Go To Pinpoint Test M . B2738 Pedal Travel Sensor Velocity Error ABS Module Go To Pinpoint Test M . B2740 Pedal Travel Sensor Spike Error ABS Module Go To Pinpoint Test M . B2741 Sensor Cluster Defective ABS Module FOLLOW the diagnostic tool directions for the calibration procedure. B2900 VIN Mismatch ABS Module VERIFY that the module has the correct as-built data.
  CHECK for correct powertrain control module (PCM) and ABS module configurations using the diagnostic tool. RECONFIGURE the component as necessary. FOLLOW the diagnostic tool directions for the ABS module configuration or REFER to Section 418-01 for the PCM. CLEAR the DTC. REPEAT the self-test. C1095 ABS Hydraulic Pump Motor Circuit Failure ABS Module Go To Pinpoint Test D . C1145 Speed Wheel Sensor RF Input Circuit Failure ABS Module Go To Pinpoint Test E . C1155 Speed Wheel Sensor LF Input Circuit Failure ABS Module Go To Pinpoint Test E . C1165 Speed Wheel Sensor RR Input Circuit Failure ABS Module Go To Pinpoint Test E . C1175 Speed Wheel Sensor LR Input Circuit Failure ABS Module Go To Pinpoint Test E . C1233 Speed Wheel LF Input Signal Missing ABS Module Go To Pinpoint Test F . C1234 Speed Wheel RF Input Signal Missing ABS Module Go To Pinpoint Test F . C1235 Speed Wheel RR Input Signal Missing ABS Module Go To Pinpoint Test F . C1236 Speed Wheel LR Input Signal Missing ABS Module Go To Pinpoint Test F . C1277 Steering Wheel Angle 1 and 2 Circuit Failure ABS Module Go To Pinpoint Test G . C1278 Steering Wheel Angle 1 and 2 Signal Faulted ABS Module Go To Pinpoint Test G . C1279 Yaw Rate Sensor Circuit Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1280 Yaw Rate Sensor Signal Fault (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1281 Lateral Accelerometer Circuit Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1282 Lateral Accelerometer Signal Fault (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1285 Booster Solenoid Circuit Failure ABS Module Go To Pinpoint Test I . C1287 Booster Pedal Force Switch Circuit Failure ABS Module Go To Pinpoint Test J . C1288 Pressure Sensor Main/Primary Input Circuit Failure ABS Module Go To Pinpoint Test K . C1440 (with stability assist) Pressure Sensor Main/Primary Signal Faulted ABS Module Go To Pinpoint Test K . C1516 Roll Rate Sensor Signal Fault (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1517 Roll Rate Sensor Circuit Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1730 Reference Voltage Out of Range (+5V) ABS Module Go To Pinpoint Test L . C1805 Mismatched PCM and/or ABS-TC Module ABS Module CHECK for correct PCM and ABS module configuration using the diagnostic tool. RECONFIGURE the component as necessary. FOLLOW the diagnostic tool directions for the ABS module configuration or REFER to Section 303-01 for the PCM. CLEAR the DTC. REPEAT the self-test. C1963 Stability Control Inhibit Warning ABS Module This DTC is for information only. GO to the Principles of Operation. CLEAR the DTC. REPEAT the self-test. C1991 Module Calibration Failure ABS Module Follow the diagnostic tool directions for the calibration procedure. C1996 Active Yaw and/or Roll Control Disabled ABS Module This DTC can be set if the ABS module system is activated for 15 seconds of continuous operation. CHECK for any major chassis modifications, gross suspension misalignment or other items that can alter the vehicle tracking dynamics. CLEAR the DTC. REPEAT the self-test. C1998 Module Calibration Not Complete ABS Module Go To Pinpoint Test O . C2769 (ABS only) Longitudinal Acceleration Sensor Electrical Failure ABS Module INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. CLEAR the DTCs. REPEAT the self-test. C2769 (ABS with stability assist) Longitudinal Acceleration Sensor Electrical Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C2770 (ABS only) Longitudinal Acceleration Sensor Plausibility Failure ABS Module INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. CLEAR the DTCs. REPEAT the self-test. C2770 (ABS with stability assist) Longitudinal Acceleration Sensor Plausibility Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C2777 Sensor Cluster Bus Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C2778 Sensor Cluster Power Supply Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . U1900 CAN Communication Bus Fault-Receive Error Network Fault REFER to Section 418-00 . U1901 CAN Network #2 Communication Bus Fault-Receive Error Network Fault Go To Pinpoint Test H . U2023 Fault Received from External Node Instrument Cluster REFER to Section 418-00 .

B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart.
Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index DTCs DTC Caused By Description Action B1342 ABS Module ECU is Defective INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. B1484 ABS Module Brake Pedal Input Open Circuit Go To Pinpoint Test D . B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart. B1676 ABS Module Battery Voltage Out of Range Go To Pinpoint Test E . C1145 ABS Module Speed Wheel Sensor RF Input Circuit Failure Go To Pinpoint Test B . C1155 ABS Module Speed Wheel Sensor LF Input Circuit Failure Go To Pinpoint Test B . C1165 ABS Module Speed Wheel Sensor RR Input Circuit Failure Go To Pinpoint Test B . C1175 ABS Module Speed Wheel Sensor LR Input Circuit Failure Go To Pinpoint Test B . C1222 ABS Module Speed Wheel Mismatch Make sure the tires are the same size and correctly inflated. INSPECT the wheel speed sensor rings. CLEAR the DTC. TEST drive the vehicle. REPEAT the self-test. C1266 ABS Module ABS Valve Power Relay Circuit Failure Go To Pinpoint Test K . C1296 ABS Module Wheel Speed LF Signal Fault Go To Pinpoint Test C . C1297 ABS Module Wheel Speed RF Signal Fault Go To Pinpoint Test C . C1298 ABS Module Wheel Speed RR Signal Fault Go To Pinpoint Test C . C1299 ABS Module Wheel Speed LR Signal Fault Go To Pinpoint Test C . C1300 ABS Module ABS Hydraulic Pump Motor Circuit Failure Go To Pinpoint Test A . C1805 ABS Module Mismatched PCM and ABS Modules Do Not Match CHECK the part numbers. INSTALL the correct module. C2775 ABS Module TC ON/OFF Switch Stuck Failure Go To Pinpoint Test H . U0073 CAN Bus Control Module Communication Bus Off REFER to Section 418-00 . U1900 CAN Bus CAN communication Bus Fault - Receive error REFER to Section 418-00 . U2023 CAN Bus Fault received from External Node REFER to Section 418-00 .

I would pull the fuse for the ABS hydraulic pump and then put it back in and see what happens. Don't ever recall a pump running. Dealer may need to hook up scan tool for diagnostic fault codes, DTCs.



Principles of Operation
The ABS control module receives wheel speed readings from both front wheel speed sensors and the rear differential speed sensor, and processes this information to determine if an ABS event is necessary. The wheel speed sensor electrically senses each tooth of the ABS sensor indicators as it passes through the wheel speed sensor's magnetic field.
The ABS control module continuously monitors and compares the rotational speed of each wheel speed sensor indicator and, when it detects an impending wheel lock, modulates brake pressure to the appropriate brake caliper(s). This is accomplished by triggering the hydraulic control unit (HCU) to open and close the appropriate solenoid valves. Once the affected wheel returns to normal speed, the ABS control module returns the solenoid valves to their normal position, and normal (base) braking resumes.
The ABS control module is self-monitoring. When the ignition switch is turned to the RUN position, the ABS control module will do a preliminary electrical check, and at approximately 20 km/h (12 mph), the pump motor is turned on for approximately one-half second. Any malfunction of the ABS system will cause the ABS to shut off; normal power assisted braking, however, remains.
Inspection and Verification — Scan Tool Communications Check

1. Verify the customer concern by carrying out the Drive Cycle Test.

1. Visually inspect for obvious signs of mechanical and electrical damage.

Visual Inspection Chart Mechanical Electrical

• Parking brake cable
• Tire pressure
• Tire size or mismatched tires

• Blown fuse
• Central junction box (CJB):
  • fuse 23 (10A)
• Battery junction box
  • fuse 102 (50A)
• Connectors or connections
• Ground integrity
• Harness routing
• Wire chafing
• Circuitry open/shorted

-----------------------------------------------------------------------
Anti-Lock Control The four-wheel anti-lock brake system (4WABS) consists of the following components:

• Anti-lock brake control module (2C265)
• Front anti-lock brake sensor (2C204)
• Front anti-lock brake sensor indicator (2C182)
• Hydraulic control unit (2C219)
• Rear anti-lock brake sensor (2C190)
• Rear anti-lock brake sensor indicator (2C189)
• Yellow ABS warning indicator

Anti-Lock Control —Vehicles Built After 03/2002 The 3-channel anti-lock brake system consists of the following components:

• front wheel speed sensors
• front wheel speed sensor rings
• hydraulic control unit (HCU)
• Anti-lock brake control module (ECU)
• rear wheel speed sensor
• rear wheel speed sensor rings
• yellow anti-lock brake warning indicator

The 4-channel anti-lock brake system with traction control and stability assist system consists of the following components:

• active brake booster with integral solenoid
• brake booster release switch
• front wheel speed sensors
• front wheel speed sensor rings
• hydraulic control unit (HCU)
• stability assist module (ECU)
• stability assist event indicator
• lateral accelerometer
• longitudinal accelerometer (4x4)
• rear wheel speed sensors
• rear wheel speed sensor rings
• steering wheel position sensor
• yaw rate sensor
• yellow anti-lock brake warning indicator
• brake pressure transducer
• traction control switch

---------------------------------------------------------------------
I suspect the abs issue is causing the speed control not to work if it happened at the same time the cruise control stopped working. When the yellow ABS light comes on, it means the ABS is dactivated. You may have a faulty accelerometer which senses acceleration and yaw (side to side lean). I have not seen a bad one but you said it is sensitive to acceleration.
I would unplug it and see what happens. The connector should have a small tab to depress so you can pull the connector out.
Here is where it is:

Accelerometer Removal and Installation

1. NOTE: The accelerometer is located under the center, rear passenger seat carpet. (I think you have to remove seat for access).
   Cut the carpeting along the perforations.

1. Disconnect the electrical connector.

1. Remove the nuts and remove the accelerometer.

Have dealer hook up tester and pull fault codes if you can't find an easy solution.
Some background info

A malfunction in the anti-lock brake system will cause the anti-lock brake control module to shut off or inhibit the system. However, normal power-assisted braking remains.

Malfunctions are indicated by the yellow ABS warning indicator in the instrument cluster.

The anti-lock brake system is self-monitoring. When the ignition switch is turned to the RUN position, the anti-lock brake control module will carry out a preliminary self-check on the anti-lock electrical system indicated by a three-second illumination of the yellow ABS warning indicator in the instrument cluster.

During vehicle operation, including normal and anti-lock braking, the anti-lock brake control module monitors all electrical anti-lock functions and some hydraulic operations.

Each time the vehicle is driven, as soon as vehicle speed reaches approximately 20 km/h (12mph), the anti-lock brake control module turns on the pump motor for approximately one-half second. At this time, a mechanical noise may be heard. This is a normal function of the self-check by the anti-lock brake control module.

Pedal pulsation coupled with noise while braking on loose gravel, bumps, wet or snowy roads is normal and indicates correct functioning of the anti-lock brake system.

Warning Lamp Indicator
The anti-lock brake system (ABS) uses the yellow ABS warning indicator to alert the driver of a malfunctions in the ABS.
The yellow ABS warning indicator will come on to warn the driver that the ABS has been turned off due to a symptom that exists in the ABS. Normal power assist braking remains but wheels can lock during a panic stop while the yellow ABS warning indicator is illuminated.

-----------------------------------------
Please report back, I am curious if that is what it is. Good luck

It is picking up a signal from one of the wheel sensors probably.

Go here to read files on ABS issues

http://autos.groups.yahoo.com/group/villagerquest/

• Anti-Lock Brake Warning Indicator Always On

• Fuse(s).
• Circuit.
• Hydraulic solenoid relay.
• Hydraulic pump motor relay.
• Brake anti-lock sensor(s).
• Hydraulic anti-lock actuator assembly.
• Anti-lock brake control module.

• GO to ABS Quick Test .

QT5 PERFORM ABS TROUBLE CODE RETRIEVAL

• Key OFF.
• Jump Pin 4 of the data link connector to ground.
  
  
  
  
• Key ON.
• Observe the anti-lock brake warning indicator.

NOTE: The first code to flash will be the start code (12). Also, each code is repeated three times before proceeding to the next trouble code.

Does the anti-lock brake warning indicator flash codes? Yes No RECORD code(s). GO to the following ABS Trouble Code Identification Chart in this section and PERFORM Pinpoint Test specified for first code retrieved. If indicator is illuminated constantly, GO to Pinpoint Test D1 . If indicator is not illuminated, GO to Pinpoint Test A1 .

abs relay some times go bad