Question about 1990 Chevrolet Caprice

1 Answer

1990 caprice wagon. Looking for the small lights on the lower side between front bumper and wheels. cannot even find what they are called.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 381 Answers

Http://cgi.ebay.com/ebaymotors/DOT-NEW-CORNER-LIGHT-PARK-PARKING-SIDE-18-Mos-Warranty-_W0QQcmdZViewItemQQfitsZYearQ3a1990Q7cModelQ3aCapriceQQhashZitem2c5877f333QQitemZ190462817075QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

copy and past this link I think this is what you are looking for

Posted on Nov 15, 2010

  • Ron A Martinson Nov 15, 2010

    Actually after reading your qustion again I think you are looking for these. Copy and past this link


    http://cgi.ebay.com/ebaymotors/80-90-Cap...

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlight removal


Yes, the bumper has to come off to remove the headlights.
There will be a number of smaller screws around the outside of the bumper, like in the wheel well and under the car by the splash shield under the engine. All of those will need to be removed. Then you need to remove the turn signal lights in the front bumper with a long phillips screwdriver. Take a flashlight and look inside the bumper through the lower grill at the side of the turn signal housing. You'll see a small hole for the screwdriver. The screw doesn't need to come all the way out to remove the light.
Remove turn signal housing on both sides and look back at the frame crossmember behind the bumper. There are two large bolts on each side holding the bumper on. You'll need some extensions to reach them. Once those are out, you'll be able to tell if you missed any smaller screws/clips. Carefully move the bumper cover out of the way to have access to the headlight mounting points.

Mar 24, 2014 | 1996 Honda Accord

1 Answer

Remove front bumber 1996 honda accord-lx


There will be a number of smaller screws around the outside of the bumper, like in the wheel well and under the car by the splash shield under the engine. All of those will need to be removed. Then you need to remove the turn signal lights in the front bumper with a long phillips screwdriver. Take a flashlight and look inside the bumper through the lower grill at the side of the turn signal housing. You'll see a small hole for the screwdriver. The screw doesn't need to come all the way out to remove the light.
Remove turn signal housing on both sides and look back at the frame crossmember behind the bumper. There are two large bolts on each side holding the bumper on. You'll need some extensions to reach them. Once those are out, you'll be able to tell if you missed any smaller screws/clips.

Mar 24, 2014 | 1996 Honda Accord

1 Answer

1995 Chevy Caprice Wagon, right side signals and brake lights dont work


change the bulb if still out then check and test socket/ground wiring/wire harness for damage

Apr 28, 2017 | Cars & Trucks

1 Answer

How to remove a bumper on a peugeot 308


I have just finished replacing the broken grille on my wife's Peugeot 308 (09 reg) wiuth the help of a YouTube video in Russian .... http://www.youtube.com/watch?v=3-KxbwKnvJE ...not that I could understand what they were saying but at least you can follow what they are doing.

If attempting this, allow a good three hours which is what it took me as there are many bolts to undo and a knack of pushing and pulling fragile plastic lugs. Take your time.

Removal can be done without putting car on ramps as you will need to put the wheels on full lock to get at the wheel-arch liners.

Firstly, undo the various screws on the plastic tray underneath the engine which connect to the front bumper skirt. There are three main bolts with washers which are located half way back, one central and one each side.

Secondly, put the steering on full lock to give you access to the wheel-arch liner for each front wheel. Pull the wheel-arch liner back to reveal a 10mm bolt where the bumper meets the wing of the car. You will need a ratchet with a swivel knuckle and 10mm socket to get onto the bolt head. Undo the bolt and repeat on the other side.

Lift the bonnet and at the front edge you will see four black flat circles. Using a small flat blade screwdriver, lever up the centre and you can then lift up with your finger which releases the retaining plastic bolts.

Looking at the top of the panted front bumper where it attached to the front of the engine compartment, you will see several small slots along the width of the plastic which you can place a small flat bladed screwdriver into and push down gently whilst pulling the front panel forwards in a rocking motion to release the plastic lugs. The whole bumper assembly should then start disconnecting from the car. It is helpful to have a second person to gentle prise away the wheel-arch sections from the car body. The whole front bumper section should then fall away but be careful as the wiring for the front fog lights will still be attached. Take hold of the lamp holders and turn through 90 degrees to remove the bayonet fittings. Pull the bumper assembly clear of the car and place on a fabric cloth/mat to avoid scratching the paintwork.

Re-fitting is a reverse of the above.

Feb 23, 2012 | Cars & Trucks

1 Answer

How do you replace the headlight bulb in a 2007 bmw 328i?


You have to remove the bumper first...

Tools Required:
- socket wrench/socket kit
- 8mm socket
- 10mm socket
- flathead screwdriver
- flathead stubby
- torx driver set

Optional Tools:
- car jack
- monkey (to hold your work lights)

Instructions:
- jack up car (optional)
- At least jack up one side of the car

1) Remove 4 screws on top of bumper ( under hood, above kidney grills)
2) Remove 2 screws in each wheel-well, and clip bumper trim away from wheel-well trim
3)Push wheel-well trim away so you can unfasten 2 screws inside that hold top part of bumper to the car on each side
4) Release about 7 Screws on bottom of bumper from underneath
5) Remove bumper by uncliping each side and then pulling bumper forward

Foglights will stay in place. simply disconnect the cable.

After you remove the bumper and unplug the Foglights
1) To remove the lights you also need to remove the bracket that hold the lights
2) Remove the blots on the bracket and top of headlight.

Installation is in the reverse of removal...

Oct 21, 2010 | 2007 BMW 328xi Sports Wagon

1 Answer

Can you help me dis-assemble my front bumper honda odyssey 1999 ?


Front
  1. Note the radio security code, then disconnect the negative battery cable.
  2. Remove the bolt from the lower part of the bumper just in front of the wheel opening, and remove the self-tapping screw from the rear most portion of the bumper at the forward portion of the front wheel well.
  3. On V6 Odyssey models, perform the following:
    • Remove the grille.
    • Remove the pins and clips from the lower front of the bumper.
  4. On 4-cylinder Odyssey models, remove the bolts from the left and right side lower brackets for the bumper at the ends of the lower air intake.
  5. Pull the ends of the bumper outward.
  6. Have an assistant help guide the bumper up and away from the vehicle.
  7. Installation is the reverse of the removal procedure.

Mar 06, 2010 | Honda Odyssey Cars & Trucks

1 Answer

How do I remove the headlamp unit on a Jaguar S type 2001 I can only see two nuts one top centre and one to the left and three or four inches lower slightly to the right of the main beam looking from the...


Front bumper requires removal to gain acsess to the lower 10mm bolts. Bumper comes off by removing the 2 10mm bolts on the top of the bumper then unscrew the 2 T30 screws in the front wheel arch liner (bumper side) and then you will be able to see a 10mm bolt reversed into a bracket at the top of the bumper from a inside veiw, remove and repeat for the other side. Then its 3 10mm bolts that secure the front under tray (if yours has one). Then there will be another 10mm bolt to the wing side of the headlamp from a above veiw. Bumper should then just pull off and watch for the connector for the fog lamp harness.

Just the 2 lower headlamp bolts andit should pull from its housing

Mar 04, 2010 | 2001 Jaguar S-Type

1 Answer

I neede to remove the headlights for my 2008 E 350 and need instructions. OIt appears that removing the front bumper is needed ? Thanks


Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.




Oct 09, 2009 | Mercedes-Benz E350 Cars & Trucks

1 Answer

How do you take bumper of vw passat 2003 to replace radiator


Tools Required
--------------------------------
T25 Torx Screwdriver
Phillips Head Screwdriver (if equipped with fog lights)
Small Flathead screwdriver
Wide Flathead Screwdriver


Bumper Removal
--------------------------------

1. Jack the car up on both sides and remove the front wheels. Use Jackstands and please observe all safety procedures. I'm sure it's possible to do this by turning the wheels to each side as you work in the wheel wells, but this was easiest for me to do.

2. Remove the hood release lever.
Pry out the plastic guide on the front of the grill, and looking directly down on the hood release lever attachment point, you'll see a metal clip. Using your small screwdriver, flip that clip up so it's off of the plastic lever and place your wide screwdriver in the Y of the plastic, turn the large screwdriver to spread the Y off the pins that it is holding on to. This can be VERY frustrating, so take your time. If you need to remove the latch cover in frustration, it's a $6 part from Liberty (experience)

3. Remove the front grill.
Just a T25 torx screw on each side and clips underneath, be careful not to break the clips as you pull it off. If you have an aftermarket grill you might have to pull through or cut off your double-sided tape

4. Remove the 3 lower grills (they just pop out, the middle one is a little tricky, just take your time and make sure all the plastic clips release)

5. Remove fog lights (if equipped) 3 screws each and disconnect

5. Remove the 4 T25 screws from the top of the bumper (under where the grill just sat)

6. Remove 4 T25 Screws from each wheel well, one is pointed straight up, you'll have to feel under the wheel well where the bumper meets the fender to find it.

7. Climb under the car and remove the 3 flat head screws (they just twist out)

8. With your helper, pull the bumper straight towards you from each side, and remove the connections from the side markers. The bumper should now be free.

Installation is basically the reverse of removal HOWEVER, there are tabs on each side of the car that line up with tabs on the bumper, be absolutely sure that these line up, they will center the bumper for you and hold it on while you screw it in.

Removing Bumper strip
-----------------------------------

1. Looking at the back of the bumper that you just removed, find the 4 tabs and 4 hooks holding the strip on. The hooks are down by the side marker holes, and the tabs are on the front of the bumper.

2. You'll see a black pin holding one of the hooks in place, if you push with a small screwdriver on the bottom of this pin, you'll see another, smaller pin come up, pull this pin out as far as you can and the large pin will pop right out.

3. With your screwdriver, carefully pry back the tabs and pull on the strip from the front of the bumper, releasing it in sections.

4. After all the tabs are removed, pull the strip away from the bumper (as if you were pulling it from off from the front of the car, and it should come right off)

I hope help you woth this. Good luck (remember rated this help).

Oct 01, 2009 | 2003 Volkswagen Passat

1 Answer

Front bumper cover is broken, no lights along bottom.


Under the bumper cover is a fiberglass bumper. It could be broken or your bumper mounts could be bent on that side. It is best to remove the screws (on the side of the wheel well) and 10mm bolts holding the bumper cover, and locate the two frontal bolts in each bracket. There are also some plastic push pin nuts in various spots too. Don't try to get the push pins under the headlights, they will come with when the bumper is removed.

Sep 25, 2009 | 1993 Honda Accord

Not finding what you are looking for?
1990 Chevrolet Caprice Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...