Question about 1990 Ford F150

1 Answer

How do it tell if oil is 2 low gauge is in normal range but low side plus 19400 mi

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,206 Answers

You must open the hood and pull the oil dipstick it is the only true way to tell if you are running low on oil.at the bottom of the dipstick it will read add or full and there will be cross hatched lines in between , oil level has to always be in that area.

Posted on Nov 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Chevy Silverado c1500 pickup has very low oil pressure, what do I need to look at?


Do not drive the truck until the issue is resolved.

1. Make sure the oil is at the proper level in the engine with the correct spec oil for the pickup. Oh it is normal for the oil pressure to be a little low at idle and go up to the normal range as the engine rpm goes up to normal operating range.

2. It could be either a real problem or a problem with the oil pressure indicator. To verify which connect a mechanical test pressure gauge of the proper range say a 0-100 psig scale to the point where the oil pressure sensor is connected. After it is connected test run the engine for a short period. If the pressure shows normal replace the oil pressure sensor. If the gauge confirms the low oil pressure then you have a serious issue in the engine. It could be:

1. Bad oil pump or oil pressure relief valve

2. excessive clearance in the bearings due to high miles.

Nov 17, 2014 | 2001 Chevrolet Silverado 1500

2 Answers

How can i fix the oil pump


see this tips and fix it. God bless you
The oil pump supplies oil to lubricate your engine. If the oil pump is worn or is not turning, the engine will suffer a loss of oil pressure, which may result in engine damage or engine failure.
The first sign of trouble may be a low oil pressure warning light, a drop in the normal reading on you oil pressure gauge (if your car has one), or the appearance of ticking or clattering sounds from your engine.
As a rule, most engines only need about 10 PSI of oil pressure for every 1,000 RPM of engine speed. Oil pressure will read higher than normal when a cold engine is first started because the oil is thick. Oil pressure will gradually drop as the engine warms up and the oil thins out. So normal oil pressure on a warm engine cruising down the highway is typically 30 PSI up to 45 PSI.
SYMPTOMS OF OIL PUMP TROUBLE
The first thing you should do if any of these symptoms occur is to stop your car, turn off the engine, let it sit for a few minutes, then check the oil level on the dipstick. If the oil level is at or below the ADD line, add a quart of oil to bring the level back up to the full mark. Add as much oil as is needed to raise the level to the full mark. Then restart the engine. If the warning light remains on, or the oil pressure reading does not climb back up to its normal range, or the engine noise does not go away, you may have a bad oil pump.
The other possibilities include a bad oil pressure sending unit, or a problem with the oil pressure warning light circuit or oil pressure gauge.
OIL PRESSURE SENDING UNIT
If the engine is NOT making any unusual noises and seems to be running normally, and the oil level on the dipstick is FULL, but you are still getting a low oil pressure warning light or low gauge reading, the fault could be a bad oil pressure sending unit.
The oil pressure sending unit is mounted on the engine block. On some applications, there is a spring-loaded pressure-sensitive diaphragm with a switch inside the sending unit. This switch completes the circuit to the low oil pressure warning light if oil pressure drops below a certain threshold. The unit may stop working if the diaphragm inside fails, if the switch is stuck, if the small hole that allows oil to enter the sending unit becomes plugged, if there is a loose, corroded or broken wiring connector at the sending unit, or there is a fault in the wiring circuit between the sending unit and warming light.
On vehicles that have an oil pressure gauge (electronic, not mechanical), the oil pressure sending unit has a small rheostat inside that sends a variable voltage signal to the oil pressure gauge when the diaphragm moves. A worn spot on the rheostat or any of the other problems just described for the simple pressure-type oil pressure switches can cause a problem.
FORD'S FAKE OIL PRESSURE GAUGE
On many Ford vehicles that were built from 1980 through the 1990s, the oil pressure sending unit has two switches, a low pressure and a high pressure. These vehicles also have an oil pressure gauge, but the reading on the gauge is not a true indication of real oil pressure. As long as the pressure to the sending unit is between high and low, the gauge will read normal. If oil pressure drops and trips the low pressure switch, the dash gauge will now read low. Or, if oil pressure goes up and trips the high switch inside the sending unit, the dash gauge will read high. Consequently, don't rely on the oil pressure gauge for an accurate reading in these vehicles. It is only a gross indication if the oil pressure is low, normal or high.
OIL GAUGE PROBLEMS
If the engine is NOT making any unusual noises and seems to be running normally, the oil level on the dipstick is FULL, and you have replaced the oil pressure sending unit but are still getting a low oil pressure reading on the dash gauge, the fault could be in the wiring circuit between the sending unit and gauge, or the gauge itself might be bad.
Check the wiring connections on both ends as well as wiring continuity between the sending unit and gauge. If no wiring faults are found, hook up a pressure gauge directly to the oil pressure port on the engine and check oil pressure with the engine running. If the engine-mounted gauge shows normal oil pressure but the dash gauge is reading low, the problem is a bad dash gauge.
On the other hand, if the engine-mounted pressure gauge reads low and you have done all of the above, chances are the oil pump is worn, or it is not picking up enough oil because of a restriction or blockage in the pickup screen in the bottom of the crankcase.
OIL PUMP PICKUP PROBLEMS
The pickup tube has a screen on the end to prevent large chunks of anything bad that ends up in the crankcase from being sucked into the pump. But we are talking BIG chunks of debris, not normal wear particles or carbon or dust or other microscopic-sized abrasive particles that can cause pump wear over time.

Sep 28, 2012 | 1996 Toyota Tercel

2 Answers

Oil gauge drops low at idle


Low oil pressure at idle can be caused by an engine with worn rod or main bearings due to (usually) high mileage . This however does not mean the engine is still not serviceable as long as the oil pressure is low only at idle. The pressure should at minimum get into the normal range at anything above idle speed.Not much oil pressure is really necessary at LOW speed. At low speed, as long as there is oil getting to the bearings, even at low pressure, you are OK. In a high mileage engine the oil pressure is often low at idle simply because the oil pump is turning slowly and cannot maintain higher pressure between the larger than normal crankshaft and bearing clearances. As speed increases the pump turns faster and supplies more oil and the pressure should go higher. Low pressure as long as it is only at idle is not a problem. However at higher speeds the pressure should be in the normal range. Such a worn engine can benefit from higher viscosity (thicker) oil such as 20W-50 in above freezing weather and 10W-40 in winter. That will increase idle pressure and the thicker oil film maintains a better film between the worn parts

Apr 08, 2012 | 2002 Jeep Grand Cherokee

1 Answer

Check gages on jeep grand cherokee


If your "Check Gauges" light is on, the light means pretty much whay it says...CHECK GAUGES! One or more of your gauges is/are reading outside of normal operating range. You could be having an overheating problem (Temperature gauge near or in the red) You could be having a charging system problem (Battery or Amp gauge reading in the "discharge" or "low voltage" area.) You could be nearly out of fuel (Fuel gauge reading near empty) Your oil pressure could be low (OIl Pressure gauge reading very low)....You have to look at your gauges to find out what is going on that is not normal.

Jan 29, 2011 | 2003 Jeep Grand Cherokee

1 Answer

The truck f 150 ford dont star was un used for long time aroun one yaer and now said check gauges what is that?


The check gauges light will come on when one of the gauges is not in a normal range, either low fuel, low oil pressure, over heating, or low battery. Since the truck sat for so long, my guess would be low battery.

Oct 16, 2010 | 2004 Ford F150

2 Answers

How many pounds of r134 and how much oil ozs.


somewhere around 1.6 pounds (1lb.14ounces) of R134a if system is evacuated and 3 ounces of oil with new compressor.
keep pressure on the low side around 34-37psi & it should blow snow. Below are normal car AC pressure readings with 134A.
  • Normal readings on high and low side with AC OFF (static pressure) – Depends on outside temperature, but normally is between 80-105 PSI
  • Normal low side reading with AC on high speed and MAX & engine at 800-1000 RPM’s – Ranges from 25-35 PSI –
  • Normal high side reading ranges from 200-350 PSI
Don’t assume that if adding little Freon is good that adding a lot is better! Overcharging just a little can decrease the performance of the system and possibly damage the compressor.
DIY recharge kit:
With the AC on the coldest setting, use a thermometer in a middle vent. Normal vent temperature readings will vary depending on the (ambient) outside temp. The vent temperature should range from around 42-55 degrees in my experience. If normal gauge readings are obtained and the vent air is cold – STOP don’t overcharge the system.
Thank you for using fixya and be safe.

Jul 19, 2010 | 1994 Chevrolet S-10 Blazer

1 Answer

My a.c is not cooling i put freon in and my compressor will only come on every now an then i replaced the switch in the dash but still did not help i did use a jumper wire to my compressor and it...


You may not have enough R134a in the system, or you have over charged the system and your high pressure switch is turning your compressor off when the pressure get's to high.
You really need a A/C gauge set to see of your system is over or under charge. If it's under charge, that's good. A over charged system will cause your a costly repair of replacing a $300.00 rebuilt compressor plus the vacuuming out the system and replacing the accumulator which may have parts from the compressor (bearing).
Normal readings on high and low side with AC OFF (static pressure) – Depends on outside temperature, but normally is between 80-105 PSI
Normal low side reading with AC on high speed and MAX & engine at 800-1000 RPM’s – Ranges from 25-35 PSI – Note that on many Chrysler products a normal reading on the low side may be 15-25 PSI
Normal high side reading ranges from 200-350 PSI
Could be overcharged, not enough air going across condenser fins, compressor not pumping sufficiently… BOTH gauge readings are really needed to get a better idea.
Don’t assume that if adding little Freon is good that adding a lot is better! Overcharging just a little can decrease the performance of the system and possibly damage the compressor, assuming the blower speed is on high, AC is set on maximum and engine is around 2,000 RPM’s

1. Check the high and low gauge readings with the AC on & set on MAX/Recirculate, middle vents with the engine at 2,000 RPM’s, blower speed on high.
2. Check the vent temperatures with a thermometer from the middle vents, far right & far left vents?
3. What is the outside temperature at the time the readings were taken? 4. Check to see if the condenser fan blowing strong?
5. Notice if compressor clutch is cylcling excessively.



Thank you for using fixya and good luck


Jun 12, 2010 | 1994 Toyota 4Runner

1 Answer

I may need a new oil sender/switch for my Capri XR2. My mechanic can't find the OEM one, it's discontinued. I have found some aftermarket ones with a range of 15-100 PSI. I read that operating pressure is...


I myself would go for the pressure sensor, should be located either on the side of the block or on the side of the side of the oil pan. If you're concerned about the reading, the aftermarket sensors you mentioned should work just fine.

May 30, 2010 | 1991 Mercury Capri

1 Answer

95 Deville - Low Refridgerant/AC Comp. off


To diagnose problems, an A/C manifold gauge set is needed to read high and low side pressure readings. Avoid adding refrigerant with a simple charging kit like the ones sold at parts stores. Don’t add any stop leak, this can cause problems in the compressor, expansion valve or condenser.
Keep in mind that using an A/C gauge set and seeing BOTH high and low side readings can help in diagnosing the problem when you know what to look for. First, on a 134A system the high and low side service ports are different sizes. AC gauge sets have color coded hoses, the blue color coded hose has a connection that fits on the low side service port and the red hose has a connection that will only fit onto the high side. The yellow hose won’t hook up to anything if just checking the readings; it can be used to connect to a vacuum pump or attached to a refrigerant can or tank.

Normal readings on high and low side with AC OFF (static pressure) - Depends on outside temperature, but normally is between 80-105 PSI
Normal low side reading with AC on high speed and MAX & engine at 800-1000 RPM’s - Ranges from 25-35 PSI - Note that on many Chrysler products a normal reading on the low side may be 15-25 PSI
Normal high side reading ranges from 200-350 PSI

Don’t assume that if adding little Freon is good that adding a lot is better!  Overcharging just a little can decrease the performance of the system and possibly damage the compressor.

Both low and high side readings are lower than normal, this indicates a cars AC system is low on refrigerant and is under-charged.
If both low and high side readings are too high, this indicates an overcharged system - too much refrigerant. This also can indicate that the condenser fan is not working, is too slow or the car is overheating and heat is transferring from the radiator to the condenser.

Good luck and hope this helps, keep me posted be glad to answer any question you may have. And yes the A/C system on your car uses R143a and there is a A/C pressure switch along the low pressure line or on the accumulator, it looks like a oil pressure sensor with a two wire lead cliped on it. 

Jul 02, 2009 | 1995 Cadillac DeVille

3 Answers

Low oil pressure after engine has heated up.


With the car warmed up, oil pressure should be 1.5 kg/cm^2 @ 800 rpm. If your not getting that much, you may want to get an oil pressure gauge (mechanics type) to check it. 8d774a8.gif Using this type of gauge will give you an accurate reading. The stock gauge may not be very accurate, especially if the sending unit is old.

7a5c4c7.jpg
a3499dc.jpg
9a6435d.jpg

Feb 10, 2009 | 1991 Nissan 240SX

Not finding what you are looking for?
1990 Ford F150 Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...