Question about Ford Contour

1 Answer

Remove and repair rear seat center seat belt retractor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,585 Answers

To remove the rear seat, If there are no bolts, Push at the bottm of the seat, towards the back of the car, the is a wire catch about where your legs would set. as you are pushing lift it up slightly, there is another one on the other side, when you do this one lift it out. your probably going to have to replace the retractor, you can't get parts for these. check it good first, because I have found pennies in them and they tend to mess them up. you can also clean them if they are fill with dirt and soda. if you do get it working dry graphite lube works well on them and doesn't attract dirt

Posted on Nov 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix a jammed rear seat belt


You must remove the rear seat bottom and remove the bolt for the seat belt retractor, this will allow you to in jam the seat belt.

Dec 13, 2015 | Vauxhall Astra Cars & Trucks

1 Answer

The rear drivers side passenger seat in my Mercedes 2004 ml350 is stuck down...how do get it to come back up. very little room to work


Not an easy task. You likely have one of 2 problems. If center seat belt is in the seat that is down, it may be locked. If so, you need to remove the seat back cover then the seat belt retractor. You can then position the seat belt retractor upright (how it sits when the seat is up) and pull the seat belt out making slack to raise the seat. This only happens if the either the stop on the seat belt is broken or the seat belt guide on the seat back is broken. If that's not the problem, you likely have a release cable that has come loose under the seat. If you look at the half that works, you can determine what you need to move on the locked seat and try to get to it with a long tin screwdriver or similar implement.

Mar 01, 2015 | 2004 Mercedes-Benz ML 350

2 Answers

I have a 2003 pt cruiser the air bag light stays on , code for open driver's door retractor, clean connector and check wires, light went out till next start up the light came back on , removed con


The seat belt switch cannot be adjusted or repaired and, if ineffective or damaged, the entire front seat belt and retractor (drivers side) must be replaced.
For more details on this issue,click the link below:-----
http://technoanswers.blogspot.in/2012/06/pt-cruiser-seat-belt-and-retractor.html

-------
This will help.
Thanks.

Jun 25, 2012 | Cars & Trucks

1 Answer

Replacing brake light above trunk on 2006 chrysler


This is quite a process....

Removal
1) Disconnect and isolate the negative battery cable.
2) Remove the rear shelf trim panel.

3ca61c4.jpg
3) Disconnect the CHMSL electrical connector (1).

7bde5c5.jpg

4) Remove the two mounting fasteners (3) to the CHMSL (2).

6793725.jpg

Installation is opposite of removal.

Rear shelf trim panel

Removal

1) Disconnect and isolate the battery negative cable.
2) Remover the right and left lower and upper C-pillar trim.
3) Remove the nut that secures the center rear seat belt lower anchor to the stud on the floor panel and feed the seat belt webbing back through the opening in the top of the rear shelf panel trim (2) to the retractor.
4) Remove the push-pin fastener (1) that secures the trim (2) to the rear shelf panel.
5) Slide the trim forward to disengage the S-clip that secures the underside of the trim to the to the center of the shelf panel.
6) Remove the trim from the rear shelf panel.

24614b2.jpg

Installation

1) Position the trim (2) onto the rear shelf panel(3).
2) Slide the rear edge of the trim rearward to engage the lens bezel of the center high-mounted stop lamp and far enough to engage the S-clip that secures the underside of the trim to the center of the shelf panel.
3) Install the push-pin fastener (1) that secures the trim to the rear shelf panel.
4) Pull the center rear seat belt lower anchor and belt webbing from the retractor through the opening the the top of the rear shelf panel trim and back down to the stud on the floor panel.
5) Install and tighten the nut that secures the seat belt lower anchor to the stud on the floor panel. Tighten the nut to 34 N m (25 ft. lbs.).
6) Reinstall the right and left upper and lower C-pillar trim.
7) Connect the battery negative cable.

841a5de.jpg

C-pillar trim removal

1a140ec.jpg

5ad047d.jpg

b674bd4.jpg
cf360b2.jpg

cd4ac09.jpg
2e5b4da.jpg

Seat removal

d276bae.jpg
60b3895.jpg

469e099.jpg

087d2a6.jpg

3ad2dc9.jpg


a09baad.jpg
4981771.jpg


Hope this all gets it done for you........

Feb 23, 2010 | 2006 Chrysler 300

1 Answer

Somehow a passenger of mine managed to get the


Check the owner's manual. There is usually a release for the headrest hidden under it. If not, you may need to remove the back seat by pulling it away from the back of the car.

Another fix if all else fails is to carefully remove the trim panel where the seat belt retractor is and then disconnect the retractor, reclaim the belt and then securely refasten it.

Jan 13, 2010 | 1998 Pontiac Sunfire

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?


please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal
  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

1 Answer

How do we fix front passenger side seat belt retractor on 1999 Ford Taurus? It will not pull out....


you may have to remove the bolt that holds the buckle to the floor. Try to push the belt into the retractor and see if it frees up.

I assume you are saying it is in the locked mode. It has an automatic lock mode for holding a child seat. When the belt is pulled all the way out, it goes into locking mode. You will hear it ratchet when the belt starts going back in.



Section 01-20A: Restraints, Active 1999 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Safety Belt, Lap/Shoulder The dual locking mode retractor on the shoulder belt portion of the combination lap/shoulder safety belt for the front seat passenger and rear seat outboard passengers operates in two ways:
  1. In the vehicle sensitive (emergency locking) mode, the shoulder belt retractor will allow the occupant freedom of movement, locking tight only on hard braking, hard cornering or impacts of approximately 8 km/h (5 mph) or more. The front and rear outboard seat belt retractors can also be made to lock by pulling/jerking on the belt.
  1. In the automatic locking mode, the shoulder belt retractor will be automatically locked and remain locked when the combination lap/shoulder safety belt is buckled and does not allow the occupant freedom of movement. This mode provides tight lap/shoulder belt fit on the occupant and on a child safety seat or infant carrier installation restraint.
  1. When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch to the vehicle sensitive (emergency) locking mode.
sxh~us~en~file=ani_caut.gif~gen~ref.gif WARNING: REAR-FACING INFANT SEATS SHOULD NEVER BE PLACED IN THE FRONT SEATS.
The automatic locking mode must be used when installing a child safety seat on the front passenger seat and rear outboard seats where dual locking retractors are provided

Apr 21, 2009 | 1999 Ford Taurus

1 Answer

1996 Lincoln Continental Rear Passenger seat belt retractor


do not touch,spring loaded and sealed ,renew only

Dec 19, 2008 | 1996 Lincoln Town Car

1 Answer

Seat Belt repair/replace


  1. Remove front seat.
  2. Remove adjuster cover. A
  3. Slide floor anchor cover.
  4. Remove floor anchor bolt. B
  5. Remove shoulder anchor bolt. C
  6. Remove front and rear kicking plate, then remove center pillar upper and lower garnish.
  7. Disconnect seat belt pre-tensioner connector.
  8. Remove the screw securing seat belt pre-tensioner retractor, then remove seat belt and seat belt pre-tensioner retractor.
  9. Remove bolts securing seat belt adjuster, then remove seat belt adjuster. Reverse procedure to install.J

Nov 03, 2008 | 2000 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...