Question about 1992 Honda Accord

Open Question

I have a 1992 Accord exr 2 door with the 2.2 engine, F22A6 I am about to adjust the valves and need to set up TDC , do I use the red mark or the white mark on the flywheel for ensuring TDC. Thanks DAN

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 28 Answers

SOURCE: crankshaft pulley timing marks

the red mark is where the timing is supposed to be after u have bypassed the electronic advance.the first white line on the left is tdc.
thanks for useing fixya

Posted on Aug 18, 2008

Ad
justuscc
  • 360 Answers

SOURCE: 1992 honda accord

there are two sets on the front of the trans depends on the one you ned to replace

Posted on Sep 18, 2008

Ajkill
  • 2035 Answers

SOURCE: Alternater replacement

TO remove :

  1. With the ignition OFF, disconnect the negative battery cable.
  2. Remove the power steering pump. Refer to for the complete procedure.
  3. Remove the cruise control actuator but do not disconnect the actuator cable; simply move the unit out of the way with the cable attached.
  4. Unplug the multi-pin electrical connector.
  5. Remove the terminal nut and remove the wire from the terminal.
  6. Loosen the adjusting bolt; remove the alternator nut.
  7. Remove the belt from the alternator pulley.
  8. Remove the adjusting bolt, the lower through-bolt and the small support stay.
  9. Support the alternator. Remove the upper through-bolt and remove the alternator.
  10. If desired, remove the alternator mounting brackets.
  11. If the alternator brackets were removed, reinstall them. Coat the bolts with a thread sealer or liquid thread lock. Install the bracket bolts and tighten them to 36 ft. lbs. (50 Nm).
  12. Fit the alternator into place. Install the upper through-bolt and tighten it to 33 ft. lbs. (45 Nm).
  13. Install the small stay, the lower through-bolt and the adjusting bolt. Make certain the adjusting bolt is properly installed.
  14. Install the belt. Install the alternator nut. Adjust the belt tension. Tighten the alternator nut to 19 ft. lbs. (26 Nm).
  15. Connect the wire to the terminal and tighten the nut.
  16. Engage the multi-pin connector to the alternator.
  17. Install the cruise control actuator.
  18. Install the power steering pump.
  19. Connect the negative battery cable.15463b8.jpg

Posted on Oct 14, 2008

  • 740 Answers

SOURCE: radio code for honda accord exr 92

Can be obtained from the dealer for a FEE. It most be the original radio for this vehicle. Good Luck and Thanks for using FIX YA

Posted on Jan 16, 2009

  • 1 Answer

SOURCE: 1991 accord exr is shaking erractively

MY DAUGHTER HAD THE SAME PROBLEM. THERE IS A HOSE THAT GOES FROM THE VALVE COVER TO THE FUEL INJECTOR HOUSING. ITS ABOUT 12 INCHES LONG. THERE WAS A TINY LITTLE TEAR ON THE BOTTOM THAT I COULDNT SEE. I REPLACED IT WITH FUEL LINE TUBING THAT I BOUGHT FROM AUTOZONE. IT WORK PERFECT. I HOPE THIS IS YOUR PROBLEM. IT TOOK ABOUT 2 MINUTES TO FIX.

Posted on Mar 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the valve lash specs for 2007 Honda Accord V6?


There is a specific procedure for setting valve clearance . I highly recommend getting a repair manual for the correct specs & procedure. The engine must be at TDC with the #1 cylinder on the compression stroke , that will allow you to adjust ONLY certain valves , then you have to turn the engine one turn to TDC again only now #1 will be on the exhaust stroke & the rest of the valves can be adjusted . it's important that you know the difference between the two !

Jan 08, 2015 | Honda Cars & Trucks

1 Answer

Find tdc and adjust valves on a 325 i


With the tappet cover off, rotate the engine in the normal direction of rotation until you see #4 cylinder valves rock - open/close in succession. This will be TDC on #1 - set the valve clearances. Turn the engine until your see #2 valves rock, set #5 valves, turn the engine till #6 valves rock, set # 3 valves, turn the engine until #3 valves rock, set # 6 valves, turn engine till #5 valves rock, set # 2 valves, turn engine till #1 valves rock, set # 4 valves. Once you have located #1 TDC (the second mark in the pulley should be lined up with the cover mark), it is only 60 deg. to get to the next cylinder to set. If you accidentally go past the setting point, go back and approach the setting point again in the direction of engine rotation. When you come to setting # 6 the TDC marks should be aligned again.

Jan 29, 2011 | 2003 BMW 325

2 Answers

Car wont start , replaced timing belt. all marks online.


If you changed the timing belt already, I would turn the crank back to the marks (TDC) then pop off your distributer cap look at the rotor it should be pointing at the spark wire to the No 1 cylinder, note : if it slipped off timing you could of damaged a valve...
to know if your cam is at tdc (you would have to pop off the valve cover) as you turn watch the valves there is one with a chamber to the exhaust manifold(header) that is the wrong one to watch....the one next to it should be lifting up or closing as you turn the crank to TDC (sealing the chamber) at the same time the distributor rotor should be pointing to that point under the cap...the cap is usually have small number underneath...

Jun 17, 2010 | 1993 Honda Accord

1 Answer

I need a timing belt diagram of an F22A6 Honda Accord Aerodeck Engine. Can anyone help?


There are a heap of Areodeck Manuals at

www.hondahookup.com/manuals.

Just register with the site and you can pull them down for free :)

Hope you find what you are after

Feb 24, 2010 | 1992 Honda Accord

2 Answers

Timming belt broke on 92 accord,set cranke to tdc


you will need to open the engine up if you can not turn the cam fully. something has been bent or broken or else it will turn. by breaking your timing belt was it shredded? if so you do have internal damage

Feb 11, 2010 | 1992 Honda Accord

1 Answer

I need the valve adjustment on subaru push rod engine


engine cold.
use firing order 1324

use timing marks put each cyl on tdc

inl = 0.08inch
exh = 0.010

adjust with locknut screw syst

good luck

Nov 09, 2009 | 1992 Subaru Legacy

1 Answer

Need diagram showing timing adjustment for a 1992 honda accord 2.2 engine see no timing marks how do i set timing


Check the position of the timing marks. The timing pointer mustbe perfectly aligned with the TDC (white mark) on the flywheel orflex-plate; the camshaft pulley must be aligned so that the word UP isat the top of the pulley and the marks on the edge of the pulley arealigned with the surfaces of the head. Additionally, the face of thefront timing balancer pulley has a mark which must be aligned with thenotch on the oil pump body. This pulley is the one to the left crankwhen viewed from the pulley end.

Also, in here, 1994-Honda-Accord-Coupe-Section-01-Engine (page 47 and next / TDC marks) you can find referenece information about Accord Engine.

If you need more details, visit autozone.com (free register) and select your model vehicle.

I hope help you (remember rated this help) Good luck.

Sep 25, 2009 | 1992 Honda Accord

1 Answer

Honda Accord Solenoid Compatibility Question...


As far as I know they are not interchangeable...and as you have found out they are not cheap either

Aug 27, 2009 | 1992 Honda Accord

1 Answer

1991 accord exr is shaking erractively


MY DAUGHTER HAD THE SAME PROBLEM. THERE IS A HOSE THAT GOES FROM THE VALVE COVER TO THE FUEL INJECTOR HOUSING. ITS ABOUT 12 INCHES LONG. THERE WAS A TINY LITTLE TEAR ON THE BOTTOM THAT I COULDNT SEE. I REPLACED IT WITH FUEL LINE TUBING THAT I BOUGHT FROM AUTOZONE. IT WORK PERFECT. I HOPE THIS IS YOUR PROBLEM. IT TOOK ABOUT 2 MINUTES TO FIX.

Mar 09, 2009 | 1992 Honda Accord

1 Answer

Radio code for honda accord exr 92


Can be obtained from the dealer for a FEE. It most be the original radio for this vehicle. Good Luck and Thanks for using FIX YA

Jan 12, 2009 | 1992 Honda Accord

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...