Question about 2000 Toyota Tundra

Open Question

How to replace 02 oxygen sensor on 2000, tundra v-8

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: 2000 tundra v-8

No special processes. Just unplug the wire and remove the bolts. Very easy to do.
I hope that I have helped you and your problem.
The graciousness of a FixYa rating would be most appreciated.

Posted on Nov 18, 2008

01fordeb
  • 1033 Answers

SOURCE: How hard is it to replace the oxygen sensors in a

Easy, takes 10-15 min for all of them. But there a oxygen sensor tool you can buy that makes it A LOT easier for $10. It a matter of (LIKE TAKING OUT A SPARK PLUG) JUST BE SURE TO ADD ANTI SEIZE TO THREAD IF IT DOENS'T HAVE ANY. Also i work for bosch that makes these and the aftermarket is the same part even tested the same. it may look a little different but it's function is the same.

Posted on Jan 25, 2010

countrybo331
  • 79 Answers

SOURCE: engine light stays on after changing 02 sensor on

did u change the right o2 sensor there is 2 sensors on bank1 and 2 on bank2.....upstream and down stream.....i had the same prob i changed the o2 senser to the other side to check and make sure it was the o2 senser....it took 4 o2 sensors before i got 1 that finally worked nd yes i was buying them brand new.....so change sides with it nd see if the code changes sides....and did u reset it with the code machine when u put the new 1 in?

Posted on Mar 28, 2010

Testimonial: "i wont no if this is a successful answer until i can reset the code thank you"

  • 65 Answers

SOURCE: on my '02 tundra the

oxygen sensors are on the exhaust. its just a small sensor with 1 or 3 wires. bank one meens left. if its a v6 or v8. but 4 cyl engines only have one bank ,. sensor 1 meens its before the catylitic converter. sometimes right by the engine manifold and sometimes way under. just follow the pipe from the engine to the cat and u will find it. if u can get it out the new one is easy. the problem is they usualy rust in tight. they make a special socket just for them. try some PB Blaster its no joke the suff makes WD40 look like cooking oil.lol.

Posted on Nov 17, 2010

chuckster57
  • 1102 Answers

SOURCE: check engine light on my

Bank 2 will be the side that DOESN'T have the #1 Cylinder..Sensor 1 will be the one BEFORE the catalyitic convertor. On your car if it is a V6 then Bank 2 is the DRIVERS side, and if it's a V8 then Bank 2 is the PASSENGER side.

Posted on Jul 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 toyota alvalon check engine light keeps coming on for code p0171 after replacing 02 oxygen sensor in bank 1


code p 0171 refers to system too lean bank 1===causes ---intake /exhaust leak---AIR system---MAF/VAF sensor/s---fuel pressure/ pump---injector/s---heated oxygen sensor (HO2S) the one in the exhaust manifold for bank 1 nearest the firewall

Apr 15, 2017 | Toyota Cars & Trucks

1 Answer

Where is Oxygen (02) sensor on 2003 toyota tundra


O2 sensor are in the exhaust pipe. this truck should have 2 if its a 4 cylinder and 4 if its a 6 or 8 cylinder.

Sep 06, 2014 | 2003 Toyota Tundra

1 Answer

What is the P0420 code on my 2004 toyota tundra


the P0420 CODE IS INSUFFICIENT CATALYTIC FLOW , FIRST CHECK OTHER SENSORS BEFORE REPLACING THE CATALYTIC CONVERTOR, CHECK YOU REAR OXYGEN SENSOR TO MAKE SURE IT IS WORKING FINE, THEN CHECK YOUR EGR VALVE, MAKE SURE IT IS NOT LEAKING, CHECK YOU MASS AIR FLOW METER IF IT HAS ONE OR AIR FUEL RATIO SENSOR, THIS WILL BE THE TOP OXYGEN SENSOR. IF ALL GOOD THE CAT IS THE PROBLEM, THAT IS THE TOP CAT.

May 09, 2014 | 2000 Toyota Tundra

1 Answer

I need help! need to know where Oxygen sensor is located on a 2000 ford contour 2.0L 121CI L4 DOCH. Also what tools are needed to replace it?


The Contour has two 02 sensors...post cat and pre cat, which means 1 in front of the catalytic converter and 1 behind it. An oxygen sensor wrench is the best tool to use for replacing an oxygen sensor, it is slotted on the end and will slip over the wiring harness & is designed to work in tight quarters...A 7/8" or 22mm open end wrench can be used if you have room to get it on the sensor and still turn it, without busting your knuckles---Spray some WD-40 or Liquid Wrench on the old sensor and let it soak a couple of minutes, it helps.---Autozone has the 02 tool if you need to purchase one. Good luck, i hope this helps.

Jul 17, 2011 | 2000 Ford Contour

1 Answer

Check engine light on my 02 toyota tundra stays on. Diagnostics say I need to replace heated oxygen sensor, bank 2 sensor 1.


Bank 2 will be the side that DOESN'T have the #1 Cylinder..Sensor 1 will be the one BEFORE the catalyitic convertor. On your car if it is a V6 then Bank 2 is the DRIVERS side, and if it's a V8 then Bank 2 is the PASSENGER side.

Jun 26, 2011 | Toyota Tundra Cars & Trucks

1 Answer

On my '02 tundra the oxygen sensor(bank1 sensor 1) needs replacing. is it difficult, and what does it look like. my understanding is that it is licated underneath near exhaust.


oxygen sensors are on the exhaust. its just a small sensor with 1 or 3 wires. bank one meens left. if its a v6 or v8. but 4 cyl engines only have one bank ,. sensor 1 meens its before the catylitic converter. sometimes right by the engine manifold and sometimes way under. just follow the pipe from the engine to the cat and u will find it. if u can get it out the new one is easy. the problem is they usualy rust in tight. they make a special socket just for them. try some PB Blaster its no joke the suff makes WD40 look like cooking oil.lol.

Nov 17, 2010 | 2002 Toyota Tundra

1 Answer

P1176 2000 VW JETTA ALREADY CHANGED THE 02


17584/P1176/004470 - Bank1: O2 (Lambda) Correction Behind Catalyst: Control Limit Reached Possible Causes
  • Intake Air System leaking
  • Oxygen Sensor(s) and/or Oxygen Sensor Control faulty
Possible Solutions
  • Check Intake Air System for Leaks (False Air)
  • Check Oxygen Sensor(s) and/or Oxygen Sensor Control (all of them!)
This is the pre 02 sensor located before the catalytic converter.

May 10, 2010 | 2000 Volkswagen Jetta TDI

1 Answer

Error P0155


That code will not affect the drivability of the vehicle. The heater does just that: it heats up the oxygen sensor to operating temperature. You can change it yourself, raise the vehicle up, the sensor is the one on the passenger side, right after the exhaust manifold.

Thanks for choosing FixYa for advice!

Mar 05, 2009 | 2002 Toyota Tundra

Not finding what you are looking for?
2000 Toyota Tundra Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...