Question about 1994 Honda Accord

1 Answer

Just replaced the rear brakes do i have to or is it a Must to Bleed the Brakes????????????????

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honda Master
  • 5,332 Answers

If you did not replace the calipers or wheel cylinders or you did not open the bleeder screws than there is no reason to bleed the brakes. Most brake services where just the brake pads or shoes are replaced are done without bleeding the brakes.

The only time you need to bleed the brakes is if you replace a caliper, wheel cylinder, brake line, brake hose, or master cylinder.

You can also bleed or flush the brakes as maintenance. Brake fluid is hygroscopic which means it absorbs moisture. Over time this moisture will reduce the boiling point of the break fluid. Lower boiling point means that under heavy braking the brake fluid can get hot enough to boil. Once it boils you get air bubbles and lose your braking ability. So flushing/bleeding the brake system every once and a while just makes good sense.

Posted on Nov 14, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: 1996 PLYMOUTH VOYAGER SOFT BRAKE PEDAL AIR IN LINES

I am a hydraulic technician and I can tell you that air is a killer in the hydraulic system.

Start from the rear and work your way forward. I f you are using the two person method, make sure the second person keeps the master cylinder full. If the fluid level dropped anywhere in between pressing and releasing the brakes....you have a lot of air in the system.

Make sure you are tightening the bleed valve when the brake pedal is full pressed.

Remeber...start from the rear brakes first, then do the front.

Posted on Mar 16, 2009

BigBlue77
  • 59 Answers

SOURCE: how to bleed brakes

Sounds like the proportioning valve is stuck. You may need to break a front bleeder loose and hit the pedal the unseat the valve. Then blead the rearbrakse and then bleed the wheel where you broke the bleeder loose. That should work.

Good Luck

Posted on Oct 12, 2008

muttandjeff
  • 359 Answers

SOURCE: Brake problems

still got air bleed more

Posted on Nov 27, 2008

  • 8 Answers

SOURCE: How can you bleed the left rear brakes on a 2003 Jaguar X-type?

keep pumping the brakes .it will bled .

Posted on Feb 24, 2009

junmag
  • 175 Answers

SOURCE: Rear brakes wont bleed. Sucks fluid in when brakes applied. Has ABS.

try this. open the two bleeder screw at the rear calipers. leave it open untill the fluid drips generously. close the bleeder. try the brakes. if it works bleed it the nornal way. note: make sure you dont run out of fluid in the master cylinder

Posted on Jun 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have replaced 3 disc brake calipers on my 2001 pt cruiser. after bleeding all 4 brakes 3 times, I started the car and brake pedal goes to floor. is my brake booster shot?


Michael:

You must start bleeding the brakes at the wheel farthest from the master cylinder (usually the right rear), then the next farthest from the master cylinder, then the next, then the closest. If your master cylinder is at the left front of the car, start with the right rear, then the left rear, then the right front, then the left front. If you don't bleed the brakes in the correct order, you are just shifting the air in the lines from one line to another. Make sure that you close the bleeder before letting the brake pedal up, and the engine should not be running when you bleed the brakes... Make sure that the emergency brake is off. Make sure that the master cylinder does not run out of brake fluid at any time that you are bleeding the brakes.

Jan 24, 2016 | 2001 Chrysler PT Cruiser

1 Answer

I have a ford escort xr3i 1988 i have replaced the brake master cylinder, bleed the brakes but still have no brakes what could be wrong?


Your car has a diagonally split brake system. Each side of this system must be bled as an individual system, and there is a correct bleeding sequence to be followed. First bleed the right rear brake, second, bleed the left front brake, then follow with the left rear brake and lastly, bleed the right front brake.Here's a link on a repair guide for bleeding your brakes. Repair Guides Brake Operating System Bleeding The Brake System AutoZone com

May 24, 2015 | Ford Escort Cars & Trucks

1 Answer

How to bleed the brakes on a 2001 jeep grand cherokee with out the DRB scan tool


Didi all that never thing is new have no brakes can't get the air out

Dec 01, 2011 | 2001 Jeep Grand Cherokee

2 Answers

I replaced front and back brakes on my 1996 1500 Chev Suburban. Bled the brakes starting at the farthest line. The pedal is soft and travels too far. Does not seem to stop very good. What is the...


it sounds like there is still air in the brake system that has not been removed.you don`t say if you replaced the brake pads and shoes(in which case you shouldn`t need to bleed)or you replaced a brake line(s) or wheel cylinder or caliper.you will have to keep bleeding the brakes all 4 wheels(trucks don`t use bi-directional braking meaning right rear brakes with left front and so on).bleed both rear brakes then bleed both front brakes,was this problem there before you replaced the brakes(soft pedal noticed) and this is why you changed the brakes or the pedal was soft and the brakes needed changing.its possible that the master cylinder has an internal leak and may need replacing.

Apr 06, 2011 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

My 94 c1500 has very spongy brakes.I have replaced brake booster,master cylinder,porportion valve and both rear wheel cylinders.brake pedal will get firm when applied too bleed brakes but not much fluid...


You still have air in the system. You will have to bleed more. I had to bleed a quart of brake fluid out of each wheel to get good brakes on my 1996 GMC.

Jul 29, 2010 | 1994 Chevrolet C1500

1 Answer

Bleeding brakes 2000 suburban wsith ab


Why were the brake lines replaced?

Sounds like the mastercylinder may have run dry. You have to bench bleed the master and then DO NOT allow fluid to run low, while bleeding brakes...

if master cylinder runs low on fluid and air gets in, almost impossible to bleed with out releasing the lines and bleed master it self.

Sep 20, 2009 | 2000 Chevrolet Suburban

2 Answers

1999 Chevy Tahoe- Soft Brake Pedal


Try having the dealer flush and bleed your system. It is very hard to bleed ABS systems yourself and have safe brakes that still work afterward. Bleeding non-ABS brakes yourself is easy not the same for ABS brakes. Valving, sensors and what-not require a tech and the correct equipment in my opinion. You do it wrong and you could ruin your ABS system. Do that and see if they firm up. I replaced my brake shoes/pads at the same time all new everything in back, drums/springs everything and new rotors up front. then I had the chevy dealer flush, refill and bleed system. Stiffer pedal and brakes work better. Keep in mind the brakes on 99 Tahoes are inaedequate, require new rotors often, heat up and fade/glaze pads regularly. I replace my pads long before they wear down because they glaze up and start fading early. I'll rough em up once maybe, next time, new ones. Every two brake jobs, new rotors for me. Just how it is. They will stiffen a bit and work better but they will never be awesome brakes. Just how it is on 99 and earlier Tahoes. Hope it helps. Very important to bleed correctly though. I'll bleed my 83 Toyota 4x4 myself but not the Tahoe.

Aug 06, 2009 | 1999 Chevrolet Tahoe

1 Answer

Brake problems


still got air bleed more

Nov 02, 2008 | 1993 Buick LeSabre

Not finding what you are looking for?
1994 Honda Accord Logo

613 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...