Question about 1999 Lincoln Continental

1 Answer

How many bellhousing bolts are holding the transmission in my 99 lincoln continental

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,702 Answers


Posted on Nov 14, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the transmission control module on a 2001 Lincoln continental

The TCM is integrated into the PCM module. .
The PCM/ECM is under hood on the firewall around the master cylinder, there should be two to three bolts that need removal to come out on front side of fire wall. Disconnect the battery negative cable before any work is done.

Dec 01, 2016 | 2001 Lincoln Continental

1 Answer

96 lincoln continental floor shifter moves but doesn't engage transmission

Maybe shifter cable came off of the shifter inside the console ! Sometimes plastic break that hold the cable to shifter lever or down at the transmission or maybe the shifter cable broke !

Mar 27, 2015 | 1996 Lincoln Continental

1 Answer

How do I remove a vss on a 1994 Lincoln continental with a ax4s transmission

It attaches like a speedo cable used too. It just has one bolt holding it clamped into the trans tail shaft, LH side, with a plug on it instead of a cable. If you jack the rear up high, you may not lose any trans fluid. either way, check trans fluid level when you're done and make sure the plastic gear is the same color (number of teeth).

Sep 24, 2014 | 1994 Lincoln Continental

1 Answer

How do you replace the fan belt tensioner on a 2000 lincoln continental

I`m pretty sure your belt tensioner pully is just held on with a couple bolts.Remove your serpentine belt,your main belt.look at the pulley see where the bolts are that hold it on and remove them.They are spring loaded so when u take it off make sure you have the new one to put on because once you remove it ,it is no good and have to put the new one on.

Apr 02, 2014 | 2000 Lincoln Continental

1 Answer

Can't turn the flywheel on my '99 explorer sport with E code motor. trying to install last four bolts on torque converter to complete installation of transmission.

remove the splash pan from under front of engine put socket on the bolt holding the harmonic balance on u should be able to turn engine from here if not there may be other problem if the gearbox has been bolted up and the converter has not been fitted all the way into the transmission this will cause lock up loosen all bolts around bellhousing to take the weight off the try to turn the engine if its free then u will have to move the transmission back far enough to rotate the converter while pushing in it should locate and push in

Apr 24, 2011 | 1999 Ford Explorer

1 Answer


Usually not. As long as you can reach all the bolts that connect the transmission to the motor, then, no. There are usually two near the top of the bellhousing, near the floor and firewall, that are hard to reach (and hard to swing a wrench on), but (at least on the cars I have worked on) they are easier to get out than to pull the engine.

Now, if you are pulling the motor, on many cars it is easier to also pull the transmission with the motor, than to try to separate them and also support the transmission once the engine is unbolted. But the transmission is usually easier to pull by itself.

Sep 06, 2010 | 1989 Lincoln Continental

1 Answer

My 99 lincoln continental stalls when i am stopping or turning... usually when i simotaneously doing both. whats the fix?

I had the same problem with my 2001, and my problem was the Throttle Body Sensor. It is a little black sensor on the inside side of the Throttle Body. You have to take the four bolts off the throttle body to get to the two screw holding the sensor to the body

Feb 22, 2010 | 1999 Lincoln Continental

1 Answer

Removal of a starter on a 1995 lincoln continental

It should be the passenger side(right side) below the exhaust manifold, the bell housing. If you don't see it in its traditional let me know.

Apr 25, 2009 | 1995 Lincoln Continental

2 Answers


No two entirely different transmissions.
Town Car is rear wheel drive and Continental is front wheel drive

Mar 13, 2009 | 1999 Lincoln Continental

Not finding what you are looking for?
1999 Lincoln Continental Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

76682 Answers


Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides