Question about 1995 GMC Sierra

Open Question

How to change air flap actuator on 1995 gmc sierra?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
OLDERQT
  • 1 Answer

SOURCE: 93 gmc sierra heater not working

THERMOSTAT REPLACE IF NOT SEE IF HOSES ARE CLOGGED SHOT OF AIR COULD HELP OR DISSCONNECT BATTERY CABLE 10-15 MIN CONNECT BACK TRY HEATER

Posted on Jan 04, 2009

Ad
TheValley
  • 6 Answers

SOURCE: 4X4 inop on 2003 GMC Sierra 2500HD

I have found that when you are going to engauge 4x4 high, it is best to only be going about 3 miles an hour. Not faster, not stopped. It likes some movement to help it mesh. I've had perfect shifts since I started this. Hope it helps. Wade.

Posted on Jan 27, 2009

honeymokey
  • 3113 Answers

SOURCE: air blend door

Replace the broken actuator.

Posted on Apr 15, 2009

  • 6 Answers

SOURCE: 2000 gmc sierra 1500 5.3 v8. a/c heater control problem

your heat/cool and vent selection options are controlled by engine vacuum through small clear tubes attached to the rear of your climate control interface. Other vehicles have small steel pull wires that operate the desired changes. You might try removing the trim and any fasteners affiliated with the interface/console. GENTLY pull outward and look to see if any of these tubes are pulled off or cut/damaged. Did anyone recently install a new stereo in the vehicle? If so, the vacuum tubing and or pull wires that change your outlets could have been damaged when the stereo unit was pushed into place. Hope this helps

Posted on Sep 09, 2009

Testimonial: "Very good information. THANKS!"

  • 593 Answers

SOURCE: My 2004 GMC sierra blows hot air out the drivers

If you've replaced the actuators and they are working.
One of the blend doors may be broken inside the heater box. To repair or replace the broken door you
have to remove the heater box. This is not a small job. The book gives 6-7 hours for the job. There is a
cheat that I've heard good things about. I guess it can
be done in a fraction of the time. You can find out
about it at heatertreater.net I have not used it myself
but I know somone who has. And it worked well for
him. Hope this helps.

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace air flap actuator on gmc envoy slt


Air flap or mode actuators should be located on lower drivers side (slightly up and right of gas pedal) and lower left (slightly left of glove compartment). Research YouTube for removal/installation videos. Good luck.

Ron.

Dec 07, 2014 | GMC Cars & Trucks

1 Answer

1995 gmc sierra 1500 actuator looks to be working correctly but i still get a small amount of air through defrost or panel when i have the slector set to floor ? blend door ?


Does the actuator make any kind of clicking noise? That sometimes indicates that there is a broken gear tooth inside the actuator. Are we talking about a little air or a lot of air? Sometimes junk does get into the air box and will stop the door from repositioning correctly. You can try that. Yes, the blending door is directly connected to the actuator.

Dec 04, 2017 | 1995 GMC Sierra

1 Answer

1995 GMC pickup. Cold AC will blow through all settings (defrost, front vents and flloor) but warm air will not come out the defrost. You can hear something click in the dash that you assume is some kind...


good work, the clicking noise you hear is the blend door trying to move. this door is what controls the temp. the most common reason is the actuator motor is bad but sometimes the door hinge breaks, this hinge slides into actuator and is used to move the door. you will need to locate it on the heater box by locating the noise and then remove the actuator and see if the hinge is broken, i will try to enclose some picture to help you. good day, hope this helps.johnjohn2_142.jpgjohnjohn2_160.gif

Sep 24, 2011 | 1995 GMC Sierra C1500

1 Answer

I have a 1995 GMC Sierra K2500 pickup and i need to know where to find the blower motor and replace it. it will not blow out any heat right now.


I think i may have an answer for ya...Is your truck blowing air at all? if so its not within the blower...the problem is actually the a/c actuator. a little bit cheaper and easier to install...had the same problem with my truck...replaced everything but the actuator which cost a crapload of money and found out it was the actuator. your truck may require an upper and lower so check with local auto parts store...average price run about 60.00 for each.

Dec 13, 2010 | 2002 GMC Sierra C/K1500

1 Answer

My 1996 gmc sierra heater only blows out the floor even when the knob is turned to defrost...also, it squeals when the blower is on...how do i fix?


sounds like the actuator is bad also known as the blend door it flaps open and close to send air either out the top or bottom of the vehicle

Dec 06, 2009 | 2000 GMC New Sierra 1500

1 Answer

Air blend door


Replace the broken actuator.

Apr 15, 2009 | 2004 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...