Question about 2000 Chevrolet Impala

Open Question

2000 impala 3.4L. Trying to replace the cam position sensor located under power steering pump. Cant figure out how to get the pump out of the whole its sitting in. It will lift a little but cant find whats keeping it from coming all the way out.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 68 Answers

SOURCE: 05 impala steering noise. Rack or Power steering pump

the power steering fluid is probly the first thing u should check if that doesnt fix it replace ur fluid pump,.the resevior should be right around ur brake booster and master cylinder,.hope u fix it and find it

Posted on Nov 20, 2008

gregr_41018
  • 43 Answers

SOURCE: replace power steering pump on 2000 Impala w/ 3.8

remove the 2 front motor mounts and rock the motor forward by pushing the car forward while in park. make sure you flip the mounts up onto the motor they will be out of the way of smashing the radiator ... once pushed forward lock e brake to hold it there .. that should give you plenty of room to work with

Posted on Apr 19, 2009

  • 4 Answers

SOURCE: 2002 Chevy Impala Blower resistor location

It is on the passenger side, you have to remove the black plastic kick plate, below the glove box, to expose it (held in place with 2 latches and 1 push pin). The resistor is in front of the blower motor ( sandwiched between the motor housing and the firewall) it is tricky to get to, i think when i changed mine i didnt replace all the screws as they were difficult to remove and even harder to replace. Good Luck, Mike

Posted on Apr 20, 2009

  • 135 Answers

SOURCE: 2000 monte carlo how to replace water pump.last bolt

there should be holes in power steering pump pulley that when positioned correctly the bole should go through one of those holes, if not then you have to remove the pump

Posted on Apr 29, 2009

  • 521 Answers

SOURCE: Coolant Temperature Sensor location on 2006 impala

driver side of the engine block, forward and above the transmission. This piece threads into the engine block.

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my Camshaft position sensor location on 2008 Chevrolet implala 3.5L V6.


Remove the power steering pump. Refer to Power Steering Pump Replacement . Disconnect the camshaft position (CMP) sensor electrical connector. Remove the CMP sensor bolt. Remove the CMP sensor. Inspect the sensor O-ring for wear, cracks, or leakage if the sensor is not being replaced.
It's under the power steering pump .
It

Oct 21, 2015 | Chevrolet Cars & Trucks

1 Answer

Where is the crankshaft position sensor located on the 2006 Chevy Impala SS? I'm trying to replace it?


At the front of the engine on the passenger side. Behind the power steering pump. They rarely go bad. Usually the wire breaks at the plug. To date, I have never replaced one. Again, it is usually the wire.

Aug 21, 2015 | Cars & Trucks

1 Answer

SENSOR REMOVAL


If this is a 3.1L or 3.4L you must get the power steering pump out of your way the cam sensor is located on top of engine block under the p/s pump. Remove bolt with 10mm socket and carefully try to twist and pull cam sensor straight up.

Mar 07, 2014 | 2000 Buick LeSabre

1 Answer

Cant find the crank position sensor in 2000 alero


Check that the cam shaft is turning as it may have broken a timing belt. Run fault codes to check for cam/crank position sensor problems.

Jan 06, 2014 | 1999 Oldsmobile Alero

1 Answer

How to change cam sensor on pontiac GR AM 3,4L 1999


Place a jack underneath the engine with a block of wood on it as to not damage the engine and pump up the jack just enough to keep the engine from sagging down. Then remove the engine mount near the power steering unit. Removing the motor mount doesn't have to be done, but it makes it easier to remove the power steering pump (your choice). Remove power steering pump and set it aside keeping all the hoses attached. Camshaft position sensor is located beneath power steering pump. It should be held on by 1 bolt if I remember right. Disconnect the 2 wire harness and remove sensor.

Aug 27, 2013 | Cars & Trucks

1 Answer

2003 3.1L chevy malibu Cam and crank sensor location


the crank position sensor is behind the harmonic balancer and cam position sensor is just under the power steering pump

Dec 06, 2012 | Cars & Trucks

1 Answer

Where is the camshaft position sensor located on a 2006 impala 3.5L engine? And what do I have to remove to get to it?


it will be located under the power steering pump. you will need to remove pump to gain access to semnsor. do not have to take lines off just unbolt pump and can move enough

Mar 07, 2011 | 2006 Chevrolet Impala

1 Answer

Trying to locate cam sensor


the cam sensor is located on the front of the engine below the power steering pump, if you look under the power steering pump, look from the front side you will see crank sensor, heres a diagram its not labeled but if you look were the ps pump would sit you can see the wire from the cam sensor, hope this helps.9d786bd.gif

Feb 28, 2010 | 2001 Oldsmobile Silhouette

2 Answers

Where ia the powering pump fpr a 2000 chevy impala


if you have a hydraulic power steering pump it is located on the side next to the firewall and serpentine belt. useing a flash light may help.if your steering is electric there is no fluid.the electric motor is under the dash on the drivers side. hope this helps.

Nov 13, 2009 | 2000 Chevrolet Impala

3 Answers

Where is the cam switch position sensor located on a 2006 chevrolet impala


under the power steering pump should be 3 wires....if it is electronic steering then it is on the left side on top of engine block

Oct 14, 2009 | 2006 Chevrolet Impala

Not finding what you are looking for?
2000 Chevrolet Impala Logo

Related Topics:

379 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...