Question about 2004 Chevrolet Cavalier
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Sun visor on driver's side
I had the same problem in my 06 Sonata. The mechinism in the fisor that creates tension to hold it in place broke. It seems there is a certain position that if you try to rotate up or down, it cracks and goes limp. $115 for new one.
Posted on Aug 08, 2008
I resolved this same problem on my 2004 Murano after also being told that it ($350 Visor) was not covered under my extended warranty. This problem is primarily caused by the heavier than normal visor. It cost me a total of $2.69 and about 30 minutes to fix.
To resolve this problem follow the following steps:
1) Go to the hardware store and purchase the Velcro package that contains (2) 18”, 1/2 inch strips (I chose the beige color since I have a tan interior) 2) Using a small screw driver, carefully pry off and remove the small cover that hides the mounting screws for the Driver’s visor. 3) Remove the 2 Phillips screws and drop the visor down slightly so that you can unplug the wires that go to the visor light and now remove the visor 4) Using the plastic velcro strip ONLY , (NOT the fuzzy strip), trim the end of the strip so that it will fit under the visor mount and also punch a small hole in that end of the strip so that one of the screws will go through it. (There is NO NEED to remove the adhesive backing from the Velcro strip)
5) Carefully mount the visor so that one of the mounting screws also goes through the Velcro strip 6) Be sure that the sticky side of the Velcro strip faces down or towards the visor
7) Once the visor is loosely mounted, pull the Velcro strip slightly and then tighten the 2 mounting screws securely. 8) Once mounted, hold the Velcro strip against the headliner and then raise the visor against the strip and the headliner and it SHOULD stick in place since it can’t drop down because one end of the Velcro strip is secured to the visor mount 9) Trim the exposed end of the velcro strip so that only 1 inch is exposed (or less) in case you need to lower the visor at a later time. (I removed a half inch of the backing and folded the exposed end on itself so that it's easy to grasp.) In this way you don’t have to glue anything to the headliner OR the visor.
(If your visor is a vinyl material, you will have to stick/glue the fuzzy velcro strip to the top side and/or edge of the visor so that there will be something for the plastic strip to stick to)
I hope this helps others…. It works for me! (and it sure beats $350!!)
Posted on Jan 30, 2009
most of the times on the visors if you look at were it mounts on the car you will see a small screw this is a set screw and if you tighten it just a little bit it should hold your visor up for you. but not all vehicles have a set screw as iam talking about. and if the impala dosent you need to get a compleat new visor
hope this helps you out
Posted on Apr 30, 2009
most likely a defect. call the dealer and see if toyota has issued a recall on the visor and you might have it replaced for free. other than that, there's always the junkyard.
Posted on Aug 12, 2009
Tips for a great answer:
Dec 08, 2013 | 2006 Saturn ION
Aug 02, 2010 | 2007 Toyota Camry
Apr 22, 2010 | 2006 Hyundai Sonata
Dec 28, 2009 | 2005 Nissan Murano
Sep 10, 2009 | 2006 Chevrolet Impala
Mar 24, 2009 | 2007 Kia Optima
Nov 28, 2008 | 2003 Toyota Highlander
Jul 24, 2008 | 2002 Toyota Highlander
1,352 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: