Question about 1993 Mercury Villager

1 Answer

1993 mercury villager front left caliper will not release. Replaced caliper and brake line, there is no damage to the hard line. When you bleed the brakes the fluid has plenty of force and the caliper will close tight on the rotor but will not release. This was the problem I was having with the original caliper. Right front closes and releases just fine making me believe that the master cylinder is ok. Also blew out hard line and there is no blockage. What else could it be?????

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

Repalce flex line, re bleed that side.

go here for more help.

Did you lube caliper slides?

http://groups.yahoo.com/group/villagerquest/

Posted on Dec 03, 2010

  • gerry bissi Dec 12, 2010

    there is a valve screwed into the master cylinder. try loosening it and bleed that caliper again. There is a string of Q

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2920 Answers

SOURCE: Brakes on 2000 Mercury Moutaineer wont stay

did you check the master cylinder? makke sure the cap is on tight....and full of fluid

Posted on Jan 11, 2009

michigan man
  • 3533 Answers

SOURCE: 1994 mercury villager

if the car is stilling running hot check the antifreeze overflow bottle for a crack and to answer your question start the car and get it to normal temp while it is still running you open the overflow bottle fill it to the cold mark and keep adding coolant until all the bubbles are out of the system and put the cap back on right away

Posted on Jan 29, 2009

  • 1 Answer

SOURCE: How do you remove the front brake rotors on a 1997 mercury sable?

simply unbolt the caliper brackets from the steering knuckle, then the rotors come right off

Posted on Mar 22, 2009

  • 181 Answers

SOURCE: Need help bleeding the front calipers

THERE IS A BLEEDER NUT ON EACH CALIPER,ONE PERSON BLEEDS AND THE OTHER PUMPS THE BRAKE PEDAL

Posted on Oct 27, 2009

emissionwiz
  • 75822 Answers

SOURCE: trying to replace rear rotors and brake pads

u have to turn the piston clockwise as you compress it.

Posted on Nov 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 villager right front and left rear brake seizes after driving a couple of miles wont release until line is loosed


Did you by chance add power steering fluid to the brake reservoir instead of brake fluid?

Mar 01, 2015 | 1995 Mercury Villager

1 Answer

Brakes


usually when this happens its caused by the caliber being push beyond its normale operating range or contaminated brake fluid. you should change the brake caliper and flush the brake lines with brake cleaner then bleed the system with new brake fluid

Jun 04, 2012 | 1997 Mercury Villager

1 Answer

I have a 95 Villager with Anti Lock Brakes. I replaced the Pads, Calipers, Shoes and Front Brake lines. I bled the brakes according to the repair manual but, the brake light is on and the pedal still goes...


The brake bleed may not have been successful. Always bleed the right rear brake first then the left. Next the front right and then the left. If you are using someone to work the brake pedal make sure they hold it down until you have closed the bleed nipple. Make sure you use a little hose on the nipple and into a jar with fluid in it to watch for the bubbles to stop. Make sure the master cylinder always has enough fluid in it.
There is a brake bleeding kit that can be bought, this makes the job a lot easier.

Oct 07, 2011 | 1995 Mercury Villager

2 Answers

Left front caliper sticks on 93 villager after replacing caliper, rotor and brake hose


If the caliper is sticking it should have a warranty. Either installed incorrectly or it was bad out of the box. Remove and replace.

Oct 21, 2010 | 1993 Mercury Villager

1 Answer

Front brakes not releasing upon release of brake pedal. Brake pedal becoms hard and the only way to stop this is to pull over and wait 20-30 mins then it is fine for any different lengths of time from a...


sounds like the pistons in the brake calipers are rusted.(you can check this by looking sideways into the brake disc/pistons,if so replace both sides together (easy job for two people.you need 2nd to help bleed brakes) if your not into diy then do not attempt this job.....safety

Mar 02, 2010 | 1997 Mercury Villager

2 Answers

Trying to find out if my master cylinder is bad? I Replaced my front caliper it is still not retracting Broke flex line to bleed caliper, caliper retracts I think its my master but not sure


it could be the master cylinder most likely but there is a possibility the rubber lines going to the calipers if it were me i'd replace the rubber lines and the master cylinder

Oct 17, 2009 | 1998 Mercury Villager

1 Answer

Pistons in both front calipers stay out, both calipers replaced


You may have a leak in the booster or master cylinder. You can put a pressure tester on the system to test for leaks. It does sound like you have an air leak.
You can try to bleed the master cylinder, then slave cylinder, then brake lines.

Aug 24, 2009 | 1993 Oldsmobile Achieva

3 Answers

Front brakes lock up


I have a 2000 Mercury Villager doing the same thing Lf wheel drags after it gets hot, problem was abs modulator, after I replaced Lf caliper, brake hose etc it still was dragging abs modulator has filters in it that get clogged and will not release.

Aug 24, 2008 | 1994 Nissan Quest

Not finding what you are looking for?
1993 Mercury Villager Logo

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...