Question about 1999 Jeep Grand Cherokee

1 Answer

I have replaced the cooling fan relay 3 times in the past 4 months and it needs replaced again. How can i solve this problem?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 51 Answers

Sounds like the Cooling fan motor may be seizing up when it gets hot causing the relay to fail, try replacing the fan motor & relay.

Posted on Nov 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is fan motor relay located?


Search Results

    Chrysler Cooling Fan Relay - YouTube

    ? 5:00
    https://www.youtube.com/watch?v=AdIYm9kM5E0
    Jan 9, 2010 - Uploaded by realfixesrealfast
    Review the electrical diagram before you begin and this should help ... ... How To Solve An Engine Overheat Condition - EricTheCarGuy - Duration: 26:09. by ... 1999 Dodge Caravan AWD 3.8L Radiator Fan Relay Replacement for ... Terms · Privacy · Policy & Safety · Send feedback · Try something new!

    Need to find location of cooling fan motor relay - Fixya

    www.fixya.com/cars/t26003541-need_find_location_cooling_fan_motor
    4 hours ago - need to find location of cooling fan motor relay - Chrysler 1996 New Yorker question.

    Guess no-one knows where the fan motor relay is. Not ...

    images for 1996 chrysler new yorker wiring

Dec 11, 2015 | 1996 Chrysler New Yorker

1 Answer

I have an 05rendezvous,need to locate switches for cooling system,fans aren't co ming on & now I'm going to need a new radiator,cuz plastic broke.But it broke before fans gave out.Which I changed stat


The engine cooling fan system is controlled by the body control module (BCM) and the powertrain control module (PCM) or engine control module (ECM). The BCM performs the calculations as to how long, when and what speed the cooling fans should turn on. The BCM then sends a class 2 message to the PCM/ECM to engage the cooling fan relays. If there is a malfunction with the BCM, the PCM/ECM will control the engine cooling fans independently. The engine cooling system consists of 2 electrical cooling fans and 3 fan relays. The relays are arranged in a series/parallel configuration that allows the PCM/ECM to operate both fans together at low or high speeds. The cooling fans and fan relays receive battery positive voltage from the underhood accessory wiring junction block. The ground path is provided at G100.
During low speed operation, the PCM/ECM supplies the ground path for the low speed fan relay through the low speed cooling fan relay control circuit. This energizes the cooling fan 1 relay coil, closes the relay contacts, and supplies battery positive voltage from the cool fan 1 fuse through the cooling fan motor supply voltage circuit to the left cooling fan. The ground path for the left cooling fan is through the cooling fan 2 relay and the right cooling fan. The result is a series circuit with both fans running at low speed.
During high speed operation the PCM/ECM supplies the ground path for the cooling fan 1 relay through the low speed cooling fan relay control circuit. After a 3 second delay, the PCM/ECM supplies a ground path for the cooling fan 3 or S/P relay and the cooling fan 2 relay through the high speed cooling fan relay control circuit. This energizes the cooling fan 2 relay coil, closes the relay contacts, and provides a ground path for the left cooling fan. At the same time the cooling fan 2 relay coil is energized closing the relay contacts and provides battery positive voltage from the cool fan 2 fuse on the cooling fan motor supply voltage circuit to the right cooling fan. During high speed fan operation, both engine cooling fans have there own ground path. The result is a parallel circuit with both fans running at high speed.
The BCM and PCM/ECM command Low Speed Fans on under the following conditions:
?€¢
Engine coolant temperature exceeds approximately 106?°C (223?°F).


?€¢
A/C refrigerant pressure exceeds 1 310 kPa (190 psi).


?€¢
After the vehicle is shut off if the engine coolant temperature at key-off is greater than 140?°C (284?°F) and system voltage is more than 12 volts. The fans will stay on for approximately 3 minutes.

The BCM and PCM/ECM command High Speed Fans on under the following conditions:
?€¢
Engine coolant temperature reaches 110?°C (230?°F).


?€¢
A/C refrigerant pressure exceeds 1 655 kPa (240 psi).


?€¢
When certain DTCs set.


The three relays are located in the under hood fuse / relay box ! You need to have it checked for DTC'S -diagnostic trouble codes ! An you need a GM Tech 2 scan tool !
This diagnostic procedure supports the following DTCs:
?€¢
DTC P0480 Cooling Fan 1 Relay Control Circuit


?€¢
DTC P0481 Cooling Fan 2 and 3 or S/P Relay Control Circuit


?€¢
DTC P0691 Cooling Fan 1 Relay Control Circuit Low Voltage


?€¢
DTC P0692 Cooling Fan 1 Relay Control Circuit High Voltage


?€¢
DTC P0693 Cooling Fan 2 and 3 or S/P Relay Control Circuit Low Voltage


?€¢
DTC P0694 Cooling Fan 2 and 3 or S/P Relay Control Circuit High Voltage


  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the Fans Low Speed ON and OFF.
Do the low speed engine cooling fans turn ON and OFF with each command?
Go to Step 3
Go to Step 4

3

Important:: A 3 second delay occurs before the powertrain control module (PCM)/engine control module (ECM) changes the cooling fan speed.
With a scan tool, command the Fans High Speed ON and OFF.
Do the high speed engine cooling fans turn ON and OFF with each command?

Aug 08, 2015 | Cars & Trucks

2 Answers

2004 Chevy Monte Carlo 3.4 the a/c stopped blowing,then it started overheating to the red within a couple miles,replaced the thermostat,the relay switch some days it overheats sometimes it runs fine


Are the cooling fans coming on ? What relay switch did you replace ?
The BCM will request low speed cooling fan operation from the PCM under the following conditions:
?€¢
Engine coolant temperature exceeds approximately 103?°C (217?°F).


?€¢
When A/C is requested and the ambient temperature is more than 10?°C (50?°F).


?€¢
A/C refrigerant pressure exceeds 1310 kPa (190 psi).


?€¢
After the vehicle is shut off if the engine coolant temperature at key-off is more than 117?°C (243?°F) and system voltage is more than 12 volts. The fans will stay on for approximately 3 minutes.


The engine cooling fan system consists of 2 electrical cooling fans and 3 fan relays. The relays are arranged in a series/parallel configuration that allows the PCM to operate both fans together at low or high speeds. The cooling fans and fan relays receive battery positive voltage from the engine wiring harness junction block. The ground path is provided at G101.
During low speed operation, the PCM supplies the ground path for the low speed fan relay through the low speed cooling fan relay control circuit. This energizes the FAN CONT #1 relay coil, closes the relay contacts, and supplies battery positive voltage from the FAN CONT #1 fuse through the cooling fan motor supply voltage circuit to the right cooling fan. The ground path for the right cooling fan is through the FAN CONT #2 relay and the left cooling fan. The result is a series circuit with both fans running at low speed.
During high speed operation the PCM supplies the ground path for the FAN CONT #1 relay through the low speed cooling fan relay control circuit. After a 3-second delay, the PCM supplies a ground path for the FAN CONT #2 relay and the FAN CONT #3 relay through the high speed cooling fan relay control circuit. This energizes the FAN CONT #2 relay coil, closes the relay contacts, and provides a ground path for the right cooling fan. At the same time the FAN CONT #3 relay coil is energized closing the relay contacts and provides battery positive voltage from the FAN CONT #2 fuse on the cooling fan motor supply voltage circuit to the left cooling fan. During high speed fan operation, both engine cooling fans have there own ground path. The result is a parallel circuit with both fans running at high speed.
Is your vehicles check engine light lit ?
Is the

Jul 10, 2015 | Cars & Trucks

1 Answer

A/C


dear you should replace expansion valve . together with compressor make sure add
. cooling fan is working when a/c on

Apr 14, 2013 | 2007 Skoda Roomster 1.4

2 Answers

The electric fan operates all the time on low speed. Is there a normally open or normally closed sending unit causing this problem? CAN YOU HELP ME WITH THIS? Every morning the battery has run down due...


If the radiator cooling fan is staying on all the time then this is the sign of a failed fan relay. The cooling fan relay is located under the right headlamp assembly.

Dec 22, 2010 | 2000 Jeep Grand Cherokee

3 Answers

I have a 04 sante fe 2.7l 4 cylinder.The problem is the radiator cooling fansare not coming on,even once the engine has warmed up past the half way mark on the guage.The car has been overheating...


There is a cooling fan switch normally located near the thermostat housing or in the head near the thermostat housing. check this and see if it is defective.

Sep 05, 2009 | 2004 Hyundai Santa Fe

4 Answers

2002 Lincoln LS overheating


The cooling fan on the LS-V8 is hydraulic yes. But it also has a pressure switch on the pump that drives the fan. It is controlled by the temperature sensor. All these things must be taken into account. But the whining sound my lead me to believe that the pump is either low on fluid or is wearing out. The fluid the fan pump uses is the same as the power steering pump container so check it first. The same thing happened to my wife's Lincoln. I replaced the fan as well because everybody told me to do that but it didn't work. I found out that the fan is just a hydraulic motor in reverse it only spins as fast as the pump makes it spin and that is controlled by the temp. sensors. When the engine get's hotter the pressure goes up and the fan spins faster. This adds more power to the engine when it's running cooler because the fan doesn't have to spin at max speed. So good luck. I hope this has solved your problem.

Apr 01, 2009 | 2002 Lincoln LS

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...