Question about 1996 Saturn SL

Open Question

1996 saturn sl needs lower ball joints - 1996 Saturn SL

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: need location of thermostat in 98 saturn sl series

Front of the motor, low, in the fitting where the radiator hose goes into the motor; not the one on the drivers side. The fitting is rounded and is held on with two bolts.

Posted on Dec 05, 2008

  • 2920 Answers

SOURCE: looking for the thermostat location 1996 saturn sl

follow the upper radiator hose to the top of the engine it will lead you right to it

Posted on Dec 25, 2008

  • 24 Answers

SOURCE: Both lower brake and left tail light out on 97 Saturn SL.

under the dash the owners manual should tell you what amp fuse it is and where it can be found

Posted on Mar 29, 2009

  • 299 Answers

SOURCE: replace spark plug wires 1996 saturn sl series

engine side 1234/coil side 4123,all left to right.

Posted on Jun 17, 2009

emissionwiz
  • 75814 Answers

SOURCE: i need to replace the ball joint on my 93 saturn,

you will need to remove all the brake hardware and remove the strut and then purchase or rent a Ball joint press or remove the lower control arm and have a machine shop press the joint out. U will need a front end alignment after this is done.

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove and replace front ball joints?


The ball joint is sold as part of the lower control arm and the whole arm has to be replaced.

Aug 17, 2013 | 1996 Saturn SL

1 Answer

Where are the grease zerks located on a 1996 Old Ciera S.L.?


they are located on the bottom center of the ball joints and the bottom center of the outer tie rod ends below the joint.at the rear of the suspension in the same location on the ball joints if this set up has rear ball joints.if you don`t see them it may have joints that are what they call permanetly sealed joints and don`t need grease.they should be checked for being worn out.

Jun 08, 2011 | 1996 Oldsmobile Cutlass Ciera

1 Answer

Front right ball joint broke


I think the ball joint is pressed into the lower control arm so you replace the whole shooting match. Doing the other side at the same time would be a good idea.

Dec 26, 2010 | 2000 Saturn SL

3 Answers

How do you remove ball joints from lower control arm on a 1996 blazer s10 4x4(driver/front) .i went to salvage yard and removed but had to buy both arms,nuckle and tie rod. could not separate


By the time you drive the ball joints out of the control arms,they will not be worth driving back in and using,these parts need to be new,the used ones are worn also.

May 23, 2010 | 1996 Chevrolet Blazer

2 Answers

Lower ball joint replacement 1996 ford taurus. wiil I need to remove the the joint houseing from strut?


You remove lower control arm of the chassis where they are located . Do not remove upper mounting strut bolts, remove only two bolts that hold strut to sterrink knuckle.

Jan 08, 2010 | 1996 Ford Taurus

1 Answer

My lower ball joint broke and wheel fell off lower control arm the shop was unable to locate the new ball joint.the old ball joint was welded on temporarily to drive car. can i find just the ball joint or...


Ball joints just dont "fall off". Ball joints should be easily available. I'm sure the dealer can get any part you need. You may need other pieces. Have a RELIABLE shop check it over, your life is at risk, dont try cheap fixes.

Dec 17, 2009 | 1996 Acura RL

1 Answer

I need to replace the ball joint on my 93 saturn, i have the whole control arm i would like to replace


you will need to remove all the brake hardware and remove the strut and then purchase or rent a Ball joint press or remove the lower control arm and have a machine shop press the joint out. U will need a front end alignment after this is done.

Jul 22, 2009 | 1993 Saturn SC2

1 Answer

Need to replace left side drive shaft on my 1999 saturn sl1


Drain Trans,Remove lower ball joint nut & separate the knuckle from ball joint.Remove 30mm axle nut & gently pry out the axle from trans then tap out axle from hub.

Apr 12, 2009 | 1999 Saturn SL

Not finding what you are looking for?
1996 Saturn SL Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...