Question about 2008 Dodge Grand Caravan

Open Question

How to remove front bumper cover for 2008 dodge caravan

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: 2005 Honda Accord Front Bumper cover replacement

easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time

Posted on Jul 03, 2009

tommyboinow
  • 324 Answers

SOURCE: trying to remove radiator,condenser,fan assy,

you should not have to remove the bumper to replace these, you will have to remove the core support, wich you will see 2 bolts on each side, just oin front of the radiator....

Posted on Nov 26, 2008

  • 1596 Answers

SOURCE: replacing front bumper on 1999 buick regal

7/16th or 10mm Sheetmetal nuts All over Behind the Bumper Thak Bumper off first

Posted on Jan 16, 2009

  • 840 Answers

SOURCE: 2008 Dodge Caravan Overhead Console Rattles

I hate to tell you this they really can not do anything they may just make sure its all pushed in/ What happens is plastic and plastic meet and when they shift it causes noise even if you took it back to dodge they would take it out and because all the snap ins are plastic it could make it worse I have seen that happen If you took it back to dodge atleast it would be noted every wherever you take the vehicle so thats the good news but its under warranty / Please rate my response Thank you very much

Posted on Jan 31, 2009

SOURCE: REMOVAL OF REAR BUMPER COVER ON 1997 DODGE STRATUS

See under the bumper its strap with clips,you must take it out from it,

Posted on Sep 10, 2009

Testimonial: "I found out there are clips on each side of the b umper under the rear 1/4 panels as well. thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dose anyone know how to remove a front bumper cover on a 2000 dodge caravan?


https://www.youtube.com/watch?v=BCaZGTz1WLw

Not the specific video for your vehicle but this can assist you in the general methods and procedures in replacing a front bumper cover.

Nov 13, 2016 | 2000 Dodge Caravan

1 Answer

I can't locate my horn on my 1996 dodge caravan


Behind the front bumper on the passenger side. Remove the bottom cover to gain access.

Nov 21, 2015 | Dodge Cars & Trucks

2 Answers

2008 ford escape. removal of rear bumper cover


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Good Luck

Feb 27, 2015 | 2008 Ford Escape

2 Answers

Where is the trans contro module in 2002 Dodge Gr Caravan


It's located behind the front bumper on the driver's side. You need to disconnect the battery, remove the left front wheel and remove enough of the retainers for the left front wheel well [plastic] shroud, to move the shroud out of the way. This gives you access to the TCM [transmission control module aka transmission computer] Diagram linked below. See

2002 Dodge Grand Caravan 3 3 TCM Location diagram Google Search

May 15, 2014 | 2001 Dodge Grand Caravan

1 Answer

Location of 2004dodge caravan cooling fan relay show photo


Remove the front number. Ou will see it riveted to the bumper frame of the drivers side. If you remove the screws that holt the top of the bumper to the upper radiator cover and gently pull back on the grill part of the bumper you will see it.

Apr 07, 2013 | 2004 Dodge Caravan

1 Answer

How do you open hood if release cable breaks on 1997 grand voyager


You may be able to go up thru the space between the grille and radiator from the bottom. Otherwise you may have to remove the front bumper cover and grille panel to gain access.

Sep 09, 2012 | 1997 Dodge Caravan

1 Answer

2011 Dodge Caravan. Ran into a metal wheelchair ramp rain. Drove back - dislodged - the black trim insert near the bottom of the plastic bumper cover. That black plastic thing has to be just put back on...


Hello Bruce...here are the steps to follow per All Data.

Release hood latch and open hood.
Remove the headlamp assemblies.
Hoist vehicle and support with safety stands.
Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
Remove front wheels.
Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
Disconnect fog lamp wire connectors, if necessary.
Lower vehicle.
Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
Remove bumper fascia from vehicle.
INSTALLATION

Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
Hoist vehicle and support with safety stands.
Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
Install front wheelhouse splash shields fasteners.
Install front wheels.
Connect fog lamp wire connectors, if necessary.
Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
Lower the vehicle.
Install the headlamp assemblies.

The "push pin fasteners" are the pain you are having i believe. They push in, but to get them out you need squeeze them on the back & pull at the same time. If you happen to break a few, you can buy them in various sizes at the auto parts store. I hope this information is helpful, an owners manual will not have any info like this in it.



12_2_2011_5_37_49_pm.jpg

Dec 02, 2011 | Cars & Trucks

2 Answers

Where is the horn located at in the motor ran over a dog my horn quit working thought it might have busted the horn under the motor


your horns are located on the drivers side in front of the wheel well,behind the front bumper cover.

Dec 24, 2009 | 2005 Dodge Caravan

1 Answer

Where is the Front impact sensor for the airbags located on a 2003 Dodge Caravan


if you were to pull the front bumper off youll see a metal cover running the width of the vehicle. there are 4 of them through there

Nov 20, 2009 | 2003 Dodge Caravan

1 Answer

I need info on how to replace the headlamp bulbs on my 2008 Chevy Malibu, can you help.


The procedure is very involved.It requires the removal of the front bumper fascia fasteners from the center and side of the headlamp to be removed.
  1. Remove the front bumper fascia fasteners from the center and side of the headlamp to be removed, full removal of the fascia is not necessary. Refer to Front Bumper Fascia Replacement.
  2. Gently pull the fascia forward to allow clearance to remove the headlamp assembly.
  3. You will also need to remove some of the fasteners at the front of the inner wheel well.
  4. The Front Bumper Fascia is the plastic cover over your front bumper.
  5. You may also have to remove the plastic cover that is located under the front of the hood over the radiator.It extends to both sides.

Oct 27, 2009 | 2008 Chevrolet Malibu

Not finding what you are looking for?
2008 Dodge Grand Caravan Logo

Related Topics:

1,036 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...