Question about Pontiac Sunfire

1 Answer

I have two connectors for my headlight wire harness per side a light gray and a dark gray,which connector is for the low beam and is this the same for both sides

Posted by on

  • swvegasjoe Nov 14, 2010

    All connectors to lights have two pins when the low beams are on I get power to both connectors

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Check how many pin in each connector 3 is for the low beam 2 is for the high beam.

Posted on Nov 14, 2010

  • swvegasjoe Nov 14, 2010

    Each connector has 2 pins none with 3

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No low beam head lights on 1999buick regal


Do you know how to do basic automotive electrical testing ?

Headlamps Inoperative - Low Beams

Disconnect the headlamp switch.
Turn the headlamp dimmer switch to the LOW position.
Using a test light, frontprobe between the headlamp switch harness connector terminal D to ground.
Does the test light illuminate? YES - NO ?

2
Using a test light, probe between the headlamp switch harness connector terminal D to ground.
Does the test light illuminate?
--
YES - Go to Step 3
NO - Go to Step 4
3
Replace the headlamp switch. Refer to Headlamp Switch Replacement .
Has the repair been made?
--
Go to Headlight System Check
--
4
Repair a poor connection or an open in circuit 1750 between the headlamp switch and the harness connector terminal A and G201.
Has the repair been made?
--
Go to Headlight System Check
--
5
Reconnect the headlamp switch.
Using a test light, backprobe between connector C201 terminal A3 and ground.
Does the test light illuminate?
--
Go to Step 6
Go to Step 7
6
Repair a poor connection or an open in circuit 10 between the harness connector C201 terminal A3 and S221.
Has the repair been made?
--
Go to Headlight System Check
--
7
Using a test light, backprobe between connector C201 terminal A2 and ground.
Does the test light illuminate?
--
Go to Step 8
Go to Step 9
8
Replace the headlamp dimmer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle .
Has the repair been made?
--
Go to Headlight System Check
--
9
Using a test light, backprobe between the underhood accessory wiring junction block harness connector C2 terminal F10 to ground.
Does the test light illuminate?
--
Go to Step 11
Go to Step 10
10
Replace the underhood accessory wiring junction block. Refer to Accessory Wiring Junction Block Replacement .
Has the repair been made?
--
Go to Headlight System Check
--
11
Repair a poor connection or an open in circuit 1201 between the underhood accessory wiring junction block harness connector C2 terminal F10 and connector C201 terminal A2.
Has the repair been made?
--
Go to Headlight

Feb 18, 2017 | 1999 Buick Regal

2 Answers

What would cause the low beam headlight not to work when all other lights work?


If you have standard halogen bulbs:

  1. Burned out light bulb; or
  2. Fried wires between the dashboard wiring harness and the headlight bulb connectors; or
  3. Fried headlight bulb connectors.
If you have HEI emitters:
  • Failed ballast.

May 11, 2015 | 2002 Mercury Grand Marquis

1 Answer

Headlights not working


1. Verify that both low beam headlights are not burned out.

2. If both headlights are OK, inspect the low beam wiring and connections.

3. Check for corrosion at connector C101

4. C101 is a 15 cavity black connector located under the battery. If OK, backprobe and ground the Dark Blue low beam wire at that point, if the lights work check the Dark Blue wire for an open back to the switch. If they do not work check for an open up to the headlights.

Apr 14, 2013 | 2000 Chevrolet Cavalier

2 Answers

I have a 1995 Ford Explorer Limited and the high beams work but the low beams and fog lights do not, please help....


These trucks are known for bad multifuction switches.
the switch that i talk of is the signal switch , the handle is the switch, it bolts to side of steering column . this switch controls the signals and the headlights and high /low beams. the other thing is the headlight switch connector, the connector some times goes bad and starts to melt or just comes out of the connector. you will need to remove the cover to steering column, the screws are located under the bottom cover in holes. remove cover and check connector and then test for power if you have power going into switch but not coming out then switch is bad.

the last thing is to make sure the bulbs are good , make sure the headlight bulbs are good , and also the driving light bulbs, test for power at the connectors to those lights to.
You will need to do a little testing to find the problem.

Nov 22, 2012 | Cars & Trucks

1 Answer

Low Beam Drivers Side doesn't work ... low voltage,


Power for the headlights on the Left side (High and low beam.) comes from the same fuse... The ORANGE wire and the ORANGE/BLACK are the same, they connect in the harness. If you only lack the 12v to make the light work connect them at the headlight assembly.

If your low beam also lacks ground the Left low beam ground is shared with the right low beam ground... Run a wire from left low beam DARK BLUE to right low beam DARK BLUE/WHITE.

If its not working now then your cursed, seek a witch doctor.

May 23, 2010 | 2004 Buick Regal

2 Answers

Generic problem for all Pontiac Sunfire Cars Driving lights and high beam not working


Check the Pink wire for high beams and the Dark Blue wire for low beams. Common locations for wiring problems are behind the headlights, under the battery tray. Check for a corroded wiring harness connector or wires at this location. If the wires or connections are found to be corroded, repair or replace the wire or connector as necessary.

Jan 06, 2010 | 2000 Pontiac Sunfire

2 Answers

I replaced the headlight bulb because the high


There should be separate relays for the low and high beams. located in the fuse box, probably under the hood. they look like plug-in small rectangular black boxes.

Dec 27, 2009 | 2003 Pontiac Grand Am

2 Answers

LOW BEAMS NOT WORKING 2002 FORD FOCUS


Hi. i recommend a thorough inspection of the wiring harness and harness connectors that led to the actual headlights. use a volt meter to test the current flow to the connectors. pull the connectors from the back side of the headlights and test all cooper contacts inside the connectors. If the wire contacts all show voltage, this will confirm a switch malfunction. it should be replaced in this case.

Now, if one or more contacts on the wires harness fail to produce any voltage, this will confirm a faulty wiring harness. replace the wiring harness in this case.

Make sure the headlight switch is in the on position when testing the wires.

Jul 30, 2009 | 2001 Ford Focus

1 Answer

Euro low beam right side brighter than left side


You have a bad ground on the left low beam. Using a test light connected to ground see what wire is positive with low beams on. Using a piece of electrical wire connect one end to ground and with the headlight connector connected to the headlight and headlights on stick the other end into back of the connector at the ground wire. If the light gets brighter, you can cut the original ground wire to the connector ( 2-3 inches from headlight connector) and run a new wire from ground and connect it to the wire at the connector. Hope this is helpful.

Jun 21, 2009 | 1994 Honda Civic

1 Answer

Driver side low beam not getting power


I replaed the hedlight relay and it worked.

Jun 19, 2009 | 2004 Saab 9-3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...