Question about Dodge Neon

1 Answer

Need to replace front engine mount and probably the rear as well. looking for a diagram of engine and transmission mounts placement and replacement procedures.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

I just randomly checked over on ebay and there are 780 service repair manuals for hyundai between 2 and 180 dollars and 35 for the subaru outback between 2 and 15 dollars. perhaps there are some for dodge as well. if you can afford to buy gas you can buy a manual at those prices.

Posted on Nov 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Ford Focus. There is a click noise (like a u-joint) in reverse and forward as I let the clutch out. I jacked the car up and checked for u-joint play but found none. the right tire has


The focus has so many engine mounts and transmission mount failures. Check the trans mount under the aircleaner assembly for cracking and excess movement when placed in gear. I dont recall front mount but if theere is movement it is best to replace them all at the same time. The trans mount and right engine mount are the easiest to replace. But for forward and backwards movements and noises replace the front ( if applicable) and rear engine mounts.

Mar 05, 2016 | 2001 Ford Focus

1 Answer

How to replace rear engine motor mount


1994-1997 Honda Accord Rear Motor Mount - YouTube

? 13:31
https://www.youtube.com/watch?v=QTDLBZonjvo
Aug 14, 2014 - Uploaded by NutzAboutBolts
1996 Honda Accord rear engine mount Tools: Impact wrench 3/8 ratchet ... Wat size are those bolts in the rear motor mount, I have to replace them ..... 1998-2002 Honda Accord 3.0 V6 Spark Plug Replacement - Duration: ...

How to Replace the Motor Mount on a Honda Accord ...

? 5:28
https://www.youtube.com/watch?v=jCIBNq0jg0U
Oct 17, 2013 - Uploaded by Chandler Cox
How to Replace the Motor Mount on a Honda Accord .... I have 2001 Accord and engine/front vibrates when car is idle. .... onreplacing and removing rear mounts for this year and model car.... 1998-2002 Honda Accord 3.0 V6 Spark Plug Replacement - Duration: 12:48. by CharlietoKind 103,467 views.

How To Change A Motor Mount and Transmission Mount ...

? 29:43
https://www.youtube.com/watch?v=vkO19Ux9q9M
May 30, 2013 - Uploaded by klowny1969
Step by step honda transmission motor mount and transmission... 2000 2001 2002 2003 2004 2005 engine mount how to replace install check change ... MAKE A VIDEO TO INSTALL THEREAR MOUNT MOTOR PLEASE .


Dec 16, 2015 | 2002 Honda Accord

1 Answer

Front motor mount needs replacement


front motor mount is the mount at the front of the engine not the front of the car

Jul 12, 2015 | 2005 Chrysler Pacifica AWD

3 Answers

How do i know which motor mount needs replacement


With car in drive/reverse and foot hard on brake if the engine moves when gas pedal is depressed and quickly released in both D&R, then that mount/mounts is defective...

Engine mount should be replaced if:

1) The hard rubber surface is covered with heat check cracks.

2) The rubber is separated from the metal plate of the engine mount.

3) The rubber is split through the center of the engine mount



The transmission case will crack or break if either engine mounts or transmission rear mount is broken...Here is a GM Service bulletin addressing the issue:

#02-07-30-024B



The transmission mount (see drawing) test:

>Raise and support the vehicle

>Raise the transmission/transaxle in order to remove the weight from the transmission/transaxle mount and create slight tension in the rubber.

Replace trans. mount if anyone of the three conditions listed above exist
...saailer





know-motor-mount-needs-replacement-veetken1ee5qxi1ah1dwzeam-2-0.png

Jan 02, 2015 | 2004 Chevrolet Impala

1 Answer

VW Jetta MKIV - G68 sensor replacement - how to lower transmission?


Use a floor jack or trolley jack under the transmission. Also use a block of wood if you have the jack on the transmission's lower pan. You will see that the whole engine and transaxle assembly will tilt down somewhat with the transmission mount removed. If it is not enough to replace the sensors, raise the jack back up and take off that dogbone, then lower the whole thing again until you can get to the sensors. Be careful when getting the mounts back on, that the engine and transaxle settle down perfectly into the mounts, so you have no vibration issues.

May 20, 2014 | 2008 Volkswagen Jetta Wagon

1 Answer

Need xplodd view of motor mounts , transmission mount , brackets on a 1996 mercury villager van


On a lift is the easiest way because you will need to raise and support the engine while the motor mount is replaced. Once you have a new mount, I would replace both while you are at it, the procedure will become self evident. Not a difficult job.

Actually this can be done at home in your driveway in a couple hours max. Raise the vehicle on jack stands and be sure to set the parking break and block the rear tires. Then use a block of wood and a floor jack under the pulley to raise the motor just enough to take the weight off the mounts. Both the front and rear mounts are attached to the same cross member and you will need to do 50% of the job of taking out the front mount to get the rear mount out and visa versa so it is worth it to replace both if you are going to do one. Remember not to tighten them down more than snug until after the weight of the motor is back on the mounts. There are torque specifications in the front of your repair manual. Of course if you have a lift great, but for most of us do not think that you cannot do this simply because you don't have a lift.


Increase Engine Horsepower.

Jun 02, 2012 | Cars & Trucks

1 Answer

My engine is been disaligned,my engine suporrt breaks easily.how can i allign my engine back?


It sounds like you have had several engine mount failures. The engine/transmission is supported on each end by
* a mount on the engine front to the body
* a mount on the top of the transmission to the body

These two support the engine L to R.

There are also mount(s) to stop the engine rolling back and forth. These are attached to car front and rear sides of the engine block or on the transmission bell housing.

I suspect that another mount other than the one you have replaced is broken.

If all the mounts are in fact OK, then you have another issue. Mounts don't just fail for no reason. You may have an axle with a failed inner CV joint. If this jams, then very high rotational loads are passed into engine mounts. A failed or locking CV will often produce steering wheel virbration or clunking noises.

Sep 07, 2011 | 1994 Honda Civic

1 Answer

My 2002 eclipse vibrates vigorously at a stop or idle... have serviced, tuned, etc etc. please help


The motor mounts are common failure points on these cars.

In particular, the transmission hanger mount and rear rollstopper mount are the worst for failure rates.

The front rollstopper is 3rd most common, and the front engine mount is least likely to fail (rare).

The mounts range from 75-125 each and require about 2.5 hours to change all four. As I said before, the front engine mount is very unlikely to need replacement though, the other 3 are likely the only ones you will see damage on.once they are removed.

Oct 16, 2009 | Mitsubishi Eclipse Cars & Trucks

4 Answers

Motor mounts and pulley tensioner


that car to my knowlege & replacemt has one engine mount by the belt & 2 tranny mounts one in the front & that canbe purchased at amazon for about $130 alot cheaper then dealer! also rear tranny can be purchase as insert or complete with bracket & mount together! have no clue on tensioner as mine has not went yet!!

Jan 22, 2009 | 1997 Buick Park Avenue

3 Answers

Motor mount


The engine mounts are located about the middle of the block on the side of the engine. The only other mount is located under transmission.

Jun 09, 2008 | 1998 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...