Question about Chrysler LeBaron

2 Answers

.i need a diagram of

Posted by on

  • 2 more comments 
  • denisegforte Nov 14, 2010

    Is this a diagram of a 1993 v6 engine? I ask because on my car the a/c unit has its own belt and is located on the front bottom of my engine.

  • denisegforte Nov 14, 2010

    so why is there such a difference in this diagram and what i am seeing under my hood?

  • denisegforte Nov 14, 2010

    no i dont have a diagram-what i am looking at under the hood of my car is as i described above. the a/c unit has its own belt and is on the bottom of the engine. this is not the same as your diagram. so whicvh is correct and hoiw doi i put this bnelt back on it. i replaced the water pump thia am and only need to put belt back to finish job.

  • denisegforte Nov 14, 2010

    The info provided does not fit with what I am actually looking at under my hood! Can anyone help me with instruction of how to put thisa belt basck on properly? My engine has two belts- not one-as shown in this diagram provided in solution 1.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,382 Answers

.i need a diagram of - b0a164e.gif

Open hood, although it is easier to reach the belt tensioner from under the car, you will need to route the belt from above. Take the tension off the belt tensioner (a breaker bar or rachet and the proper size socket with a pipe to give ya more leverage should work) and pull the belt while the tensioner is pulled away from the belt. to put new belt on, properly follow accesorie pulleys with new belt, leaving the tensioner pulley last once that far, take your breaker bar or rachet with proper size socket... and pull the tensioner away from the belt so that you can slip the belt over the tensioner, push the belt over pulley. release the tensioner and check to make sure the belt is seated properly on all pulleys.

There should be a sticker with the diagram on the right strut tower. If it is no longer there the way to find the information (and a lot more related to your vehicle) would be to buy a Haynes manual for your model from an auto parts store or go to your local library and look in a Chilton manual. Most libraries will copy the page containing the pertinent info..

Posted on Nov 14, 2010

  • Tunde Autos
    Tunde Autos Nov 14, 2010

    Yes, you can also get a Haynes manual to confirm it...

  • Tunde Autos
    Tunde Autos Nov 14, 2010

    Did you say the diagram is different, i thought the one i sent is for the V6 engine because that is what is written on the manual i got it from. Maybe a typographical error occurred. Anyway use the one you found under the hood..

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Hello Denise. Here is the diagram you are seeking

http://www.fixya.com/cars/t5499685-need_serpentine_belt_diagram

Regarding the step-by-step instructions, here you are

http://www.familyhandyman.com/DIY-Projects/Car---Truck/Auto-Repair/changing-a-car-serpentine-belt

Joe

Posted on Nov 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the alternator


Hello, Alternators are a car part that can be very costly to fix because of labor costs. But with an hour or two of time and a little elbow grease, you can do it yourself. And to replace the alternator follow the following steps below:

Step 1. Pull your car into the garage or your work area. Turn the car off and let it sit for a while to cool.

Step 2. Begin by disconnecting the negative cable of the battery.

Step 3. Remove the serpentine belt from the pulley on the alternator. Do this by using a socket wrench to turn the serpentine automatic belt tensioner so that it allows slack in the belt. Then simply slip the belt off the alternator pulley.

Step 4. Locate and disconnect all the mounting bolts on the alternator, use a vehicle specific manual if you have any trouble.

Step 5. Disconnect all wires attached to the alternator then remove the alternator from the car.

INSTALLING NEW ALTERNATOR.

Step 1. Slide the new alternator into place. Do not worry about the serpentine belt yet.

Step 2. Replace the bolts that held the previous alternator to secure the new one in place.

Step 3. Attach the wires to the new alternator the same way they were attached to the old one.

Step 4. Adjust the serpentine belt tensioner the same direction you did in Section One to put slack in the belt. Wrap the belt around the pulley of the new alternator and then remove the socket wrench from the automatic belt tensioner.

Step 5. Inspect the belt to be sure it is not snug and follows the path required in the pulley and belt configuration diagram.

Step 6. Hook the negative battery wire back to the negative terminal on the battery.

Thanks






























Jul 20, 2010 | 1995 Buick Skylark

1 Answer

Need 1993 plymouth voyager serpentine belt diagram


Which engine?
To replace the drive belt or serpentine belt on a Voyager check the engine size. For 2.4L engines, a serpentine belt runs the air conditioning compressor and alternator. For 3.0L models, the alternator and power steering share a belt with a separate belt for the AC. Dodge recommends checking the belts every 15,000 miles or 12 months for possible replacement. I have gone 3 yrs with one.. it will start squealing when you turn on the heater to defrost..

http://www.automd.com/46/how-to-replace-a-serpentine-belt/

Most replacement belts have a diagram on the package. However, the easiest way is to pay close attention to the belt you are taking off, and replace the new one the same way. The pulleys themselves are usually 'grooved' or 'smooth' which tells you whether the front or back of the belt is against it. The hardest part is figuring out how to release tension on the idler-pulley. If you can get the belt on and the idler/tension pulley (same thing) pulls the belt tight, chances are you got the belt right. If you don't know what I mean, then the mostest best way is to get a Clymer Manual and read up. Its really a simple thing to do yourself.

I used a long heavy duty screw driver to release the tension on a Pontiac Sunbird.. the belt will only fit on one way..

May 15, 2010 | 1993 Plymouth Voyager

3 Answers

Re install a serpentine belt on a 94 chrysler lebaron 3.0L


There should be a diagram attached to the car near where the belt goes showing how the belt is to run through the pulleys.
Newer vehicles have a tension pulley which is a pulley on a spring loaded arm that keeps the belt tight.

First run the belt on all the other pulleys and then use a wrench to hold the tension pulley back while you slip the belt on.

Older cars do not have a tension pulley and you had to usually loosen something like the alternator a little bit to get it on.

Mar 12, 2010 | 1994 Chrysler LeBaron

1 Answer

Serpintine belt came off of alternator on 1993 Chrysler LeBaron there is no diagram to route the belt on ,or, in the car. How is belt routed around the alternator pulley? Is there a diagram available?


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/1993/make/chrysler/model/lebaron/1993_chrysler_lebaron_drive_belt_routing_diagram.htm

Nov 22, 2009 | 1993 Chrysler Lebaron

2 Answers

Do you have a diagram on how to install a serpentine belt on a 1994 Chrysler LeBaron?


1994 CHRYSLER LEBARON - V6 3.0L 2972cc 181ci GAS FI N 3

Open the hood, the diagram for the serpentine belt is on the cowling.

From DAYCO Catalog
Belt Routing Diagram (Alt., P.S., Idler & Tens.)
9e1b1eb.jpg


From comments to other users and Lebaron Owners; for remove, starting at the alternator pulley and going clockwise around the pathof the belt, the belt drops down and forward and goes under the idlerpulley, continues forward and less steeply downward and goes around thecrankshaft pulley clockwise, rises rearward going over the top or thetensioner pulley counterclockwise, then drops down and around the powersteering pump clockwise and rises to go around the alternator pulleyclockise (which is where I started the description). To loosen thetension to remove the belt, or to give you slack to install the beltwithout having to force it over a pulley while under tension you rotatethe tensioner pulley arm around its pivot clockwise according to the'94 shop manual. It doesn't show by what means to effect this rotation,but in the earlier manual I have ('89) it shows there to be a 1/2"square hole in the tensioner arm into which you insert a breaker barwith a 1/2" square drive which gives you the temporary lever to rotatethe tensioner against its spring action. I assume there is a similar1/2" square hole on the '94 you are working with. Interestingly,between '89 and '94 the idler pulley was added, and the requiredrotation of the tension arm changed from counterclockwise to clockwiseto relieve the tension."

I think this will help you get the belt on. Good luck.

Oct 13, 2009 | 1994 Chrysler LeBaron

3 Answers

I need a serpentine belt diagram for a 1992 chrysler lebaron 3.0 liter v6


1992 CHRYSLER LEBARON - V6 3.0L 2972cc 181ci GAS FI N 3

Serpentine Belt Diagram Alt., P.S., Idler & Tens.

669b86a.jpg

More details you can find in DAYCO Catalog

I hope help you whit this (remember rated this help) Good weekend.

Oct 02, 2009 | 1989 Chrysler LeBaron

2 Answers

Where can i find a diagram to install serpentine


Most parts stores can print this out for you for free.

Sep 10, 2009 | 1991 Chrysler LeBaron

1 Answer

I dont have a diagram to run serpentine belt to a toyota camry 03


Hi

Replacing Serpentine belt on a Toyota camry 2003—


Step 1--Examine the belt placement of your Toyota Camry fan belt so that you will remember how to put it back once you have removed it. Refer to the vehicle owner's manual for further information. Locate the pivot bolt on the front passenger side of the engine. Loosen the pivot bolt with a socket wrench.


Step 2--Loosen the adjustment locking bolt that is just below the tensioner pulley with a socket wrench, and then loosen the tensioner pulley to allow the belt to move free.


Step 3--Check the belt for any signs of cracking or irregular wear, so you can fix any problems that may exist with the pulleys. Remove the fan belt from the pulleys on the engine and take it out of the engine compartment.


Step 4--Wrap the new fan belt around each of the pulleys the same way it came out. When you have the belt in place, tighten the tensioner pulley with a socket wrench.


Step 5--Tighten the adjustment locking bolt and the pivot bolt with a socket wrench, and then look over the engine to check that everything is back in place.


Step 6--Turn the vehicle engine on and watch it for a few minutes to verify that everything is operating properly, then turn the engine off.


Please refer to these links for serpentine belt diagrams—

Serpentine belt on a Toyota camry Link 1

Serpentine belt on a Toyota camry Link 2

Please do accept the solution and revert for further assistance.

Thanks
Rylee

Jul 13, 2009 | 2003 Toyota Camry

1 Answer

Need diagram of serpentine belt


As this forum will not allow images and the link for my information requires a paid subscription I propose the following: email me at curtisephlush@yahoo.com and I can sen you a document with a belt routing illustration.

Short of that, I can give you a verbal description, but it is sort of confusing:
Top of CAM to top of ALTERNATOR - bottom of ALTERNATOR to top of nearby (front) PULLEY - bottom of PULLEY to top of A/C COMPRESSOR - bottom of COMPRESSOR to bottom of CRANK - top of CRANK to bottom of middle PULLEY - top of middle PULLEY to bottom of rear TENSIONER - top of TENSIONER to back to top of CAM. Remember the serpentine belt has ribs on only one side, the ribs face AWAY from the two guide pulleys and TOWARD the pulleys on the Alternator, Compressor, Crank, Cam and Tensioner. You should tell by the pulley being smooth or ribbed as needed.

Feb 23, 2009 | 2000 Oldsmobile Intrigue

1 Answer

How to put on Serpentine belt for 92 Chrysler Lebaron 3.o liter engine


Before replacing or installing the old belt you need to check all of the pulley's that the belt rides on for play. Pay special attention to the spring loaded tensioner pulley. They can sieze and cause the belt to come off.

I found this picture it is a bit large for the screen.

80003475.gif

Aug 29, 2008 | 1995 Chrysler LeBaron

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

587 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...