Question about 2008 Chevrolet Hhr

1 Answer

Battery needs to be stationary , to keep from moving around inside of case. This prevents switch from working.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

It came with a hold down assembly, someone has thrown that away for you. Most often this happens as someone put the wrong battery in and the assembly would no longer fit, or they were just plain lazy. Go to a dealer and ask the parts guy to show you an illustrated parts breakdown of that area and you can then buy the correct parts to keep your battery from floating around. Can be dangerous in sudden stops.

Posted on Nov 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 Suburban 5.7L, automatic trans is stuck in park - no previous shifting problems, I know that the brake switch also operates the brake/transmission solenoid (BTS). Stepping on the brake pedal prior to...


There is an interlock device that prevents the transmission from being shifted without the brake being applied. Either the device failed when you last parked it or the electrical connector(if applicable) became disconnected).
If it's column shift, then dismantle the area around the steering column. ALWAYS disconnect the battery negative (ground) before working around the steering column. It's possible to set an air bag off and get your neck broken. No kidding.
If it's floor shift, still disconnect the battery negative. Can't be too safe around air bags.
Those interlocks are a bear. Most of them have a bypass, where you can insert a screwdriver, or a key (careful), and mechanically disable it. Look for a slot or small opening around the shifter. They have to have the bypass so tow truck drivers can move cars w/o the key.
Keep trying. You'll find it.

Apr 30, 2014 | Cars & Trucks

1 Answer

Do I need to disconnect negative battery cable before replacing the window switch ?


In all instances, disconnecting the power to the battery is a standard safety requirement that prevents a short from happening or from the car starting, depending on which part you are working on. I find that however, you will need to test the voltages in the lines to determine if the problem lies in the switch or the wiring, which leads me to say keep the battery connected. Just make sure the windows are rolled down and all doors unlocked, so that you can always get inside the car if needed to quickly.

Aug 25, 2013 | 2001 Lexus RX 300

3 Answers

Replace brake switch on 1995 chevy cheyenne 1500


Brake switch wiring good, can manually make switch and brake lights work. But when installed and brake pedal mashed does not work. Slight pressure on rear of switch will allow to work. How do you keep switch stationary? Switch is clamped around booster rod and has clip installed. Switch is new. Is there a brake pedal adjustment? HELP PLEASE.......... 1995 CHEVY 1500, 5.0L ENGINE

Nov 22, 2009 | 1995 Chevrolet C1500

1 Answer

2005 parking brake stuck


The parking brake cable should be replaced but in the short term try getting under the truck and grabbing the cable casing and move them around to get the seized cable inside the cable casing to release keep working the cable until it releases if this doesn't work replace both cables.

Sep 11, 2009 | 2005 Chevrolet Colorado

2 Answers

1987 300zx, AC temp. lever will not operate door to close off heater core for cold AC.


I had a similar problem. I replaced my vacuum hoses and it fixed the problem. If any one of the vacuum hoses has a hole in it or is connected wrong your 300zx will automatically start blowing hot air and you will not be able to use your temp. control switches.

Jul 08, 2009 | 1987 Nissan 300ZX

1 Answer

Switching back 4WD to 2WD - 1998 Jeep Cherokee 4L Limited Petrol


With any 4WD like this, always move a few feet in the opposite direction when disengaging. If you were moving fwd in 4wd, switch to 2wd, back up a few feet, then go fwd.

Jun 30, 2009 | 1998 Jeep Cherokee

1 Answer

Air Conditioniong not working


U may be low in Freon gas.
When Freon is low there's low pressure switch that will prevent A/C compressor clutch from engaging to protect it from failure.
So, first check Freon pressure & any leaks form lines & hoses fittings.
Even if the fan is working, that doesn’t indicate proper compressor OP'S.
Look at the compressor front side you'll see the clutch stationary while the AFT pulley moving.

Then put air-condition compressor switch to ON (Engage),
You should see the clutch engage & start rotate,
If NOT, this is very clear indication u r low in Freon.

Regards;
MAR

Jun 03, 2009 | 2003 Dodge Caravan

2 Answers

Torque converter problem??


I would check the transfer case. The transmission is shifting manually thru the gears okay. The transfer case 4x4 module is not communicating to release the case so the vehicle will move.
Make sure all the fluid levels are full.

Mar 19, 2009 | Buick Century Cars & Trucks

1 Answer

Glass on sliding door


this is the link to the information http://www.swisco.com/Screen/how-to-repl...

Opening your patio sliding glass door should be an easy task. If your sliding door is giving you a work out every time you open it, most likely it is your rollers that are causing the problem. The rollers are located on the bottom of the sliding door and give the door the ability to slide. Often times they get dirty and wear out, making it difficult to open the door. If you have an older sliding glass door your rollers may have become rusty because sliding door units did not always use stainless steel rollers.

Hiring a professional to replace your rollers could cost you around $100 not including the cost of the replacement parts. Below are detailed steps containing all the information you will need to know to replace your patio sliding glass door rollers yourself.

* Before you start, understand that you need to take the sliding glass door out of its frame to work on the rollers. The sliding glass door is heavy. You may need the assistance of another to help you remove the door.

1) Your patio glass door will have two separate glass units. One unit is the door that you slide and the other unit is stationary. First, stand outside your house and look at your sliding glass door. If the stationary unit is between you and the sliding unit you will most likely have to remove the stationary unit so that you can get to the glass sliding unit.

Before you go through the trouble of removing the stationary unit, first try to go inside your house and see if you can remove the sliding unit. Usually you cannot because there is a lip along the bottom of the patio glass door frame (it keeps moisture out of the house) that prevents the sliding glass door from being removed from the inside.

If the rollers on the bottom of the door are difficult to get over the lip, you can adjust them to help you create more room (go down to step 2). If it is not the rollers but the sliding unit�s frame preventing you from pulling the sliding unit out of the door frame, you are going to need to remove the stationary unit first before you can remove the sliding unit.

To remove the stationary unit, you first need to take out your screen door (if you have one). Lift one end of the screen door frame and use a screwdriver to lift the roller on the bottom of the screen door frame off of the track. Do this to both ends of the screen door and your screen door will pull out of the door frame.

The stationary unit is held in place by a metal piece that runs along the bottom of the track from the corner of the stationary unit to the bottom of the side jamb (there is a chance this piece is missing but if you do have one remove it from the track). After you have removed the metal piece, look for screws holding the stationary unit frame in place. After removing all of the screws try pulling the stationary unit out of the door frame. If you are having trouble pulling out the stationary unit, try placing a screwdriver between the stationary unit�s bottom frame and the track it is resting on. Lift up on the screwdriver while you have a helper pull out the stationary unit from the door frame. Be careful not to use too much force with the screwdriver so that you do not damage the door track.

2) You may need to create more room when you attempt to remove the sliding unit from the door frame. To create more room you can adjust the rollers on the bottom of the sliding unit. By turning the adjusting screws on the rollers clockwise the wheels move up into the sliding unit�s frame giving you more room. The adjusting screws are located either at the bottom of the sliding unit�s frame or in the sides of the frame. There is a chance that there are plugs covering the screws.

After you adjust both rollers (one on each side of the sliding units frame) try to remove the sliding unit from the door frame. If the unit is still getting stuck you may need to get someone to help you. Have your helper lift one side of the unit and pull outwards while you try to pry the other side of the unit over the track.

3) To remove the rollers from most sliding units you need to remove the bottom of the sliding units frame. Most likely the screw that holds the roller in place is the same screw that holds the frame together. Remove the screw from both sides of the unit. Then try to remove the bottom piece of the frame off of the sliding unit; you may need to use a rubber mallet or a piece of wood and tap on the bottom of the frame until it comes off of the sliding unit.

Now that you have removed the bottom of the frame you can take a close look at your patio glass door rollers. Remove one of the rollers and match it up with one of the rollers on this page http://www.swisco.com/page/SI/CTGY/patio...

It is a good idea to replace both sliding door rollers at the same time to prevent extra wear-and-tear to one new roller, which will have to work twice as hard when paired with an older roller.

4) After your new rollers come in, replace your old rollers with the new ones. To make it easier to install the sliding unit back into the door frame, adjust the rollers to be all the way up into the frame. Once you have the sliding unit back in the door frame you can adjust the rollers for optimal performance. Keep adjusting the rollers until the door is sliding back and forth easily

Jun 22, 2008 | 1996 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...