Question about 1993 Chrysler Lebaron

1 Answer

How to replace serpentine belt on 1993 lebaron 3.0

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers

  1. Disconnect the negative (-) battery cable from the battery.
  2. Raise the front of the vehicle safely support it on jackstands. Try to situate the vehicle at a height so that access can be achieved from below and above the vehicle.
  3. Remove the splash shield below the alternator.
  4. Loosen the alternator pivot bolt and the locking bolt.
  5. Loosen the adjusting bolt until the belt can be removed from the alternator pulley.
  6. Lower the vehicle back to the ground if access cannot be attained from above the engine compartment.
  7. Remove the locknuts securing the engine damper mounting bracket to the engine. Push the bracket towards the engine.



FIG : Fig. 13: To remove the serpentine belt from the AB model cars, first the engine damper bracket locknuts must be removed


how to replace serpentine belt - jyackle5.jpg
FIG : Fig. 14: If any of the idler pulleys were removed from the engine, make certain to reassembly them in the correct manner-Premier and Monaco vehicles


jyackle5_0.jpg
  1. Remove the accessory drive (serpentine) belt.



WARNING The accessory drive belt must be routed correctly. It is possible to install the belt incorrectly and rotate the water pump in the opposite direction causing the engine to overheat. Refer to the appropriate accessory drive belt schematic in this section for the correct belt routing.
To install:
  1. If any of the idler pulleys were removed, they must be installed with the small spacer washer between the pulley and the engine. The inside bushing is installed between the pulley and the locknut.
  2. Install the accessory drive belt on the pulleys.
  3. Install the engine damper mounting bracket onto studs in the engine front cover. Tighten the locknuts to 30 ft. lbs. (40 Nm) of torque.
  4. Raise the vehicle again, if needed.
  5. Tighten the alternator pivot bolt to 37 ft. lbs. (50 Nm) of torque.
  6. Tighten the adjusting bolt until the correct tension is obtained-refer to the tensioning procedures found previous in this section. If a new belt is installed, it should be tensioned after 7500 miles (12,070 km) of usage.
  7. Tighten the locking bolt to 20 ft. lbs. (27 Nm) of torque.
  8. Tighten the alternator pivot bolt to 37 ft. lbs. (50 Nm) of torque.
  9. Install the splash shield to the vehicle, then lower the vehicle back down to the ground.
  10. Connect the negative (-) cable to the battery.

Good Luck

Posted on Nov 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a serpentine belt diagram for a 1993 Chrysler Lebaron


Check this diagram (click for zoom)...

zjlimited_1961.jpg

Fig. 9: Timing belt routing and timing mark locations



Hope helps (remember to rate this answer).










Sep 30, 2011 | 1993 Chrysler Lebaron

1 Answer

Serpentine belt replacement for 1993 chrysler lebaron 3.0


FixYa Subscribers have access to unlimited tech support, articles, and Experts!

Aug 16, 2011 | 1993 Chrysler Lebaron

2 Answers

Serpentine belt diagram 1993 chrysler lebaron v6


b0a164e.gif


To remove the serpentine belt from the 3.3L and 3.8L engines, rotate the tensioner assembly clockwise

Jan 10, 2010 | 1993 Chrysler Lebaron

1 Answer

I need to replace my serpentine belt but i dont know the pulley route


1994 CHRYSLER LEBARON - V6 3.0L 2972cc 181ci GAS FI N 3

Belt Routing Diagram (Alt., P.S., Idler & Tens.)

ec675ed.jpg

From DAYCO Catalog

I hope help you with this. Good luck.

Oct 14, 2009 | 1994 Chrysler LeBaron

1 Answer

V -belt installition tension adjuster location?


V Belts do not have tensioners, only serpentine belts, normally. V belt systems usually have one component that adjusts and thereby tightens the belt.

Oct 10, 2009 | 1993 Chrysler Lebaron

3 Answers

I need a serpentine belt diagram for a 1992 chrysler lebaron 3.0 liter v6


1992 CHRYSLER LEBARON - V6 3.0L 2972cc 181ci GAS FI N 3

Serpentine Belt Diagram Alt., P.S., Idler & Tens.

669b86a.jpg

More details you can find in DAYCO Catalog

I hope help you whit this (remember rated this help) Good weekend.

Oct 02, 2009 | 1989 Chrysler LeBaron

2 Answers

Where can i find a diagram to install serpentine


Most parts stores can print this out for you for free.

Sep 10, 2009 | 1991 Chrysler LeBaron

1 Answer

Diagram of 1993 sepentine belt needed


go too auto zone and get a print out of it for free

Aug 22, 2009 | 1993 Chrysler Lebaron

1 Answer

How to put on Serpentine belt for 92 Chrysler Lebaron 3.o liter engine


Before replacing or installing the old belt you need to check all of the pulley's that the belt rides on for play. Pay special attention to the spring loaded tensioner pulley. They can sieze and cause the belt to come off.

I found this picture it is a bit large for the screen.

80003475.gif

Aug 29, 2008 | 1995 Chrysler LeBaron

Not finding what you are looking for?
1993 Chrysler Lebaron Logo

Related Topics:

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...