There are two screws in the arm rest and one behind the handel used to open the door. remove those. then use something flat but firm like a butter knife and work your way around the edges. pry up under the pannel and pop out each of the pins holding the panel. don't rip just pull gentle but firm.
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Remove door panels inspect for broken parts laying in bottom of door.Somtimes because of ice they can pop off track.If this is the case just put back in track and your good.If there are any broken pieces in door you will need to replace broken parts before windows will work.
Most door glass slides in from the top **** in the door. Sometimes the window seal around the window frame may have to come out and can be re-installed after you secure the glass to the track. You may have to insert the glass at an odd angle to fit it thru. Be sure to have the door panel off so you can access the track screws(bolts) and make sure you do or don't have to bond it with adhisive. A great bonding agent for this is gorilla glue, tested and still working on my friends 93grand cherokee. Good luck.
The window probably fell off track. You will have to remove all the screws and window and lock controls. Then take a large flat-head screw driver and gently pry off door panel. You will then have access to window and motor.
All its done its just come off its tracks so remove the door insert carefully place the window back on the track and tighten it up using basic tools and no the door insert/panel can come off even if the window is all the way up. Hope this helps.
probably need a new window regulator. ebay. 93 to 98 should fit.
Section 01-05: Trim, Interior
1998 Villager Workshop Manual
REMOVAL AND INSTALLATION
Trim Panel(s), Door
Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .
If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
Pull the shop rag back and forth to release the window regulator handle clip.
Remove the three cover caps and front door trim panel screws.
Remove the one front door trim panel capped screws from the door pull handle.
If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
Remove the front door trim panel.
To install, reverse the removal procedure.
Window Regulator, Power
Front Door Removal
Disconnect the battery ground cable (14301) .
Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
Remove the two front door brace bolts and the front door brace.
Disconnect the front window regulator electric drive electrical connector.
Remove the four front door window glass regulator track bolts.
Remove the three front window regulator electric drive bolts.
Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.
Ive yet seen a jeep window come off track. sounds like your window regulator is broke but hopefully im wrong. anyways, remove all the screws some have cover over them, just remove the cover and youll see some sort of screw. Then pull out and try not to breake the plastic clips that pop into door. its pretty easy once you just look at if for a min. let me know if you have anymore questions about this