Question about 1987 Toyota Pickup

Open Question

1987 toyota van alternator plug(denso) wiring color code...please as ours has burnt off and we have 3 loose wires and cant tell which goes where one green one yellow and one white ( 4th wire is easy as its #4 gauge) the pigtail is fried need to know 3 pins on alernator

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: got toyota van 84 need

HERE is a diagram of alternator wiring at alternator do you also need where wires go?b8eaacb.gif

Posted on Oct 26, 2010

doin12volt
  • 233 Answers

SOURCE: fuel injector problem

red and white with yellow go to #1 and #3.
blue and white go to #2 and #4

Posted on Jan 14, 2009

  • 20 Answers

SOURCE: 1979 Toyota Hilux alternator wiring

always, counterclockwise starting with blue, then yellow, then red

Posted on Apr 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1987 toyota pickup runs rough and alternator light is partially on and goes dimmer as throttle is increased


hi there. it sounds to me that your alternator. is on its last legs. and just holding on in there. replace / overhaul. good luck

Mar 14, 2014 | 1987 Toyota Pickup

1 Answer

2000 toyota sienna XLE: need to unplug driver door wiring


u need to use all your wiring so just cut the one at wreckers. remove all the wiring from new door. do the same an your old one before removing the door. you need to take off door panel and unclip wires from speaker power lock motor power mirror power window and switches. pull all the wires through the hole where the black tube goes between the door and cab. put new door on and pull wires back through and re attach wires. all plugs are different so you cant mess this up.

Mar 14, 2013 | Toyota Sienna Cars & Trucks

1 Answer

The plug that connects to the alternator of my van is showing that there is connection in both wires when there should only be power in one of them. Is there a diagram that shows the wiring route from the...


You have 3 wires to the alternator. The black/gray wire goes to the fuse panel to the ignition. The dark green/ orange wire goes to the engine controls system. The third wire dark green goes to the powertrain control module. The red and black/gray are tied together from battery to the alternator as well the ignition switch to make a circuit. Hope this will help you.

May 15, 2010 | 2000 Dodge Grand Caravan

2 Answers

I need the wire color code for a 1999 toyota camry o2 sensor


Well - I'm not sure which one you mean - front or rear - here is a wiring diagram that should help you though.


2d7d015.jpg

Sep 18, 2009 | 1999 Toyota Camry

1 Answer

The plug that connects to the alternator has three


Yes the White wire is the reason. It goes to the Internal Regulator.
As you view the connector that plugs into your alternator, look at where the lock tab is.
Lock tab on TOP. The Black wire goes to the Left side. The White wire goes to the Right side.

The Black wire, ties into the Red wire down in the wire loom. (The Red wire goes to the starter solenoid, and this is connected straight to the battery. This is why the Red, AND the Black wire, are both Hot wires)

The White wire goes through the bulkhead wire loom, and to the bulkhead connector.

(Down under the steering shaft, and on the firewall, you'll see a rectangular Black box shape, with a Bunch of wires, coming into it from the engine compartment. The bulkhead connector is two pieces. Following it through the firewall, the other side of it is the fuse panel)

Where the White wire connects in the fuse panel,
it should go straight to the ACC fuse. (Accessory)

May 15, 2009 | 1987 Chevrolet Camaro

1 Answer

Fuel injector problem


red and white with yellow go to #1 and #3.
blue and white go to #2 and #4

Oct 25, 2008 | 1987 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

444 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...