Question about 1994 Mitsubishi Mighty Max

1 Answer

Its to low i want to lift about 2to 3 inches how do i lift it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,489 Answers

The problem here is. if it is a 4 wheel drive, you can raise the front end by adjusting the torsion bars. If this is a 2 wheel drive model, the only way to raise the the vehicle is by replacing the rear and front springs. This what controls what they call "ride heigth" and is a critical measurement in wheel alignments. These can be found at a local salvage yard to reduce costs. Once this is done, hget the vehicle aligned so you don't ruin your tires. Let me know if you need replacement instructions.

Posted on Nov 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My meter is saying my alternator is putting out 2to 3 volts does that mean I need a new alternator ???


If your meter is correct then this is to low should be at least 13volts i presume your measuring at alternator connections and not battery terminals in case of wiring from alternator. To battery also check condition of battery get it tested in case a fault in it

Nov 06, 2014 | Cars & Trucks

1 Answer

1998 isuzu amigo 4x4 3" lift front suspension problems no travel verry stiff


if you have lifted the front suspension by 3 inches then that is 3 inches less travel for the shocky piston to move when the suspension goes down. You have probably damaged the piston and shaft of the shocky. Replace with longer travel shockys.

Jun 01, 2013 | Cars & Trucks

1 Answer

Will 235/75/r15 tires look ok with a 2 or 3 inch lift?


Were you not planning on increasing the tire size after lifting it? They may look a little small with a 3" lift, its a personal preference. If it was me, I would probably go to a larger tire like 285/75R15 or even 305/75R15. Also remember if you put a bigger tire on this thing the speedometer will be off. It will say your going 55 but you may be going 60. Also bigger tires will change the overall gear ratio. It will increase gas mileage but lower the torque to the wheels.

Jun 06, 2010 | 1997 Jeep Grand Cherokee

3 Answers

My 4 low wont work after my lift kit


Your linkage is not long enough now to engage the LOW gear in 4WD.

Mar 06, 2010 | 1997 Jeep Wrangler

1 Answer

How to remove rear seat back 1987 mustang convertable?


Tools Required:
  • 3/8 inch Drive Ratchet
  • 3/8 inch Drive 3” Extension
  • 3/8 inch Drive 10mm Socket
  • 3/8 inch Drive 13mm Socket
  • T-50 Torx Bit
  • 1/4 inch Allen Wrench
  • 3/16 inch Allen Wrench
  • 1/2 inch Wrench
  • Drill Motor
  • 1/8 inch Drill Bit
  • 5/16 inch Drill Bit
  • 2 inch Hole Saw
  • Trim Tool (Fork Tool)
  • Electrical Tape
  • Center Punch
  • Hammer
------------------- Installation:

Remove Back Seat:
  1. Locate the retainers securing the seat bottom into the vehicle, approximately 10 inches from the end of the cushion, either side. Use your thumb to push in retainer release tab. Lift the seat up to remove.
  2. Remove the two 13mm screws securing the seat back, located on each lower corner. Lift seat upward to release seat back from brackets at the top. You can carefully prop the seat back under the retracted top , use caution if choosing this method not to damage or scratch the vinyl of the seat. You can remove the seat from the vehicle completely by disengaging the flanges securing the top of the rear seat to the fabric of the convertible top well .
  3. Remove Quarter Trim Panels:
    1. Grip the Quarter Trim Panel Cap at the shoulder strap opening and lift up to dislodge the retaining clips.
    2. The inside Quarter Trim Panels are two-piece panels. Remove the upper portion of the Quarter Trim Panel from the vehicle; it is not necessary to remove the lower portion. Pull the forward edge of the trim Panel over the pinch weld in the doorjamb.
    3. Use a Door Trim Tool (Fork Tool) to dislodge the pushpin retainer at the rear edge of the Trim Panel approximately 4” down from the top, pry Trim Panel toward the outside of car to release retainer.
    for more help click this link directly
    1. http://www.americanmuscle.com/05-07-lightbar-install.html ---------

Oct 05, 2009 | 1987 Ford Mustang

1 Answer

95 f-150 3 inch lift hit bumps at 35 mph and front shakes bad


Check your wheelbearings for play and your tierod ends for play,I'm sure one of these two are at fault.

Sep 25, 2009 | 1995 Ford F150 Styleside Regular Cab

2 Answers

98 z71 pulling to the right


tire pressure low,alignment jack up the front end and wobble the tires side to side the body lift would not effect this

Jul 15, 2009 | 1998 Chevrolet K1500

1 Answer

Transmission


For your tranny, the only thing it may need is a fluid change along with a new filter. The Jeep tranny will be able to handle those rims, considering people often throw 35+ inch tires on it. I'm not sure of the lift the new rims will create, it all depends on the kind of tires you have on it. If you use a low profile tire to closely mimic the size of the original, you won't have to get a lift kit for it. But you may want to look into the cost of a 3-4 inch kit just in case.

Nov 22, 2008 | 2000 Jeep Grand Cherokee

1 Answer

Low ground clearance on 2006 B3500 Chevrolet Express Van. Is there a kit to help lift the vehicle a few inches and if so, will it affect the ride once installed.


I'm suppose to be getting information on a kit which will raise the vehicle approximately 3 inches.  Should have info. in a couple of weeks.  Thank You for your interest.

Sep 25, 2008 | Chevrolet 3500 Cars & Trucks

Not finding what you are looking for?
1994 Mitsubishi Mighty Max Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...