Question about 2001 Ford Escape

1 Answer

When accelerating fast from a stop I hear a grumbling sound. It almost sounds like a cv joint but the cv joints are fine. Could it be a motor mount?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Possible wheel bearing, u-joint, differential noise, or binding cv joint...you really would not know if they are good without removing them from vehicle, or watching the vehicle wheels move while on a lift. very unlikely that it is a motor mount. a single clunk when taking off from a light would most likely be your motor mount. the mounts just stabalize the motor and transmission from shift and torque

Posted on Nov 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CREAKING SOUND FROM FRONT WHEEL AREA


Without the benefit of hearing this I can only make a suggestion, have the constant velocity joint checked for excessive wear.

Jun 05, 2012 | Cars & Trucks

1 Answer

I am hearing a clacking sound when i accelerate. It does not need water or oil. what could the sound be?


The sound may be a CV joint when the fource is applied to it from acceleration.You should also hear it when you make a sharp turn left or right louder when given little acceleration if the CV joint is unservicable...........Hope this helps.

Sep 28, 2010 | 1992 Honda Accord

2 Answers

Hear a popping sound from passenger side front end when accelerating. What can it be? Mazda Tribute


Does it only do it while your turning,or while going in a straight line?
Might be your CV joint, if it mostly does it while turning to one side or the other.

Mar 30, 2010 | Mazda Tribute Cars & Trucks

2 Answers

When driving around corners the front end makes a wroubbling sound. on the straigth aways the sound gone. is it the CV joints? wheel bearings? U joints? or what should I be looking for? 98 Ford Escort zx2...


Does it happen turning in both direrctions? It could be cv joints. from a standstill,turn the wheel hard to the right and accelerate in a circle. do the same on a left turn. If you hear a clicking sound, it's bad cv joints. inspect the rubber boot for tears & stress cracks. once the grease escapes,the joint is no good

Feb 16, 2010 | 1998 Ford Escort

2 Answers

I just asked this question a minute ago but I want to clarify a little more. Got a buddy of mine who is having a car issue and was hoping you guys could help out. We are wondering if bad CV joints can lead...


Much of the symptoms you describe sound like a CV joint. I would take it to the dealer and insist that it be fixed... What is bothering me though is under normal operating conditions, CV joints and boots are engineered to last upwards of 150,000 miles. Some go the distance, but a lot reach the end of the road far short of their design life. According to one major aftermarket supplier of replacement axle shafts, CV joint shafts are typically being replaced at anywhere from 70,000 miles to 130,000 miles.

Read this and see if you agree...
SYMPTOMS OF CV JOINT FAILURE
Bad boots are not the only thing you need to look for. You also need to listen for noise or complaints that might indicate a CV joint problem. These include:

  • Popping or clicking noises when turning. This almost always indicates a worn or damaged outer CV joint. To verify this condition, place the vehicle in reverse, crank the steering wheel to one side and drive the vehicle backwards in a circle (check the rearview mirror first!). If the noise gets louder, it confirms the diagnosis and the need for a new CV joint or replacement shaft assembly.
  • A "clunk" when accelerating, decelerating or when putting the transaxle into drive. The noise comes from excessive play in the inner joint on FWD applications, either inner or outer joints in a RWD independent suspension, or from the driveshaft CV joints or U-joint in a RWD or AWD powertrain. The same kind of noise can also be produced by excessive backlash in differential gears. To verify the condition, back the vehicle up, alternately accelerating and decelerating while in reverse. If the clunk or shudder is more pronounced, it confirms a bad inner joint.
  • A humming or growling noise. Sometimes due to inadequate lubrication in either the inner or outer CV joint, this symptom is more often due to worn or damaged wheel bearings, a bad intermediate shaft bearing on equal length halfshaft transaxles, or due to worn shaft bearings within the transaxle.
  • A shudder or vibration when accelerating. May be caused by play in the inboard or outboard joints, but the most likely cause is a worn inboard plunge joint. Similar vibrations can also be caused by a bad intermediate shaft bearing on transaxles with equal length halfshafts, or by bad motor mounts on FWD vehicles with transverse-mounted engines.
  • A vibration that increases with speed. This symptom is rarely caused by a failing CV joint. An out-of-balance tire or wheel, an out-of-round tire or wheel, or a bent rim are the more likely causes.

Dec 12, 2009 | 2000 Honda Accord

2 Answers

2000 Subaru Outback When turning at low speeds and accelerating at low speeds, I sometimes get a metallic grinding noise. I don't hear any noise at highway speeds. What is the problem?


Sounds like your CV half shaft is has gone bad. More than likely when you look behind your front wheels you will see a rip or hole in the CV boot. You will need to replace the CV joint to fix this. Good luck and thanks for using FixYa!

Jun 27, 2009 | 1991 Subaru Legacy

Not finding what you are looking for?
2001 Ford Escape Logo

412 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...