Question about 1999 Pontiac Grand Prix

1 Answer

Front spindle nut torque spec? - 1999 Pontiac Grand Prix

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,168 Answers

Hello Gadd.
The Grand prix axle nut torque is 118 ft lbs.
It is the same torque value for the three different engines that came on the Grand Prix that model year.
There you are, thank you for using FixYa.

KL

Posted on Nov 13, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

warlock61
  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

polarcycle
  • 1392 Answers

SOURCE: torque specs for front spindle (nut hold brake drum in place)

Tighten till the wheel bearing is tight. No one really uses a specification for that, do it by feel. when the nut is tight, and there is no play in the bearing. Should be about 15-20 ft/lbs, with about .001-.003 end play if you need exact numbers though.

Posted on May 30, 2009

c17hydro
  • 2984 Answers

SOURCE: is there a torque spec on the spindle nut for the

  1. nstall the caliper mounting bolts. Perform the following procedure before installing the caliper guide pin bolts (15 Series only).
  2. Remove all traces of the original adhesive patch.
  • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
  • Apply Red Loctite#272 to the threads of the bolt.
  1. Install the caliper mounting bolts (25 series). Tighten the caliper guide pin bolts to 42 Nm (31 ft. lbs.) on the 15 series; 108 Nm (80 ft. lbs.) on the 25 series.

Posted on Nov 19, 2009

Testimonial: "thank you that was very helpful"

tneubauer
  • 437 Answers

SOURCE: torque on a 2000 dodge neon spindle nut

If you are looking for the spec on the large nut for the CV axle to hub it is 180 ftlbs

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front Skf hub bearing torque spec 2003 dodge ram 2500 turbo diesel



Tighten the spindle nut to 149 ft-lbs to seat the bearing then
. rotate the axle 5 to 10 times to seat the hub bearing, then
tighten the spindle nut to a final torque of 263 ft-lbs I would just use a good impact gun to get it there.

Oct 15, 2016 | Dodge Cars & Trucks

1 Answer

How do you install front hub assembly on 2008 nissan altima?


The torque spec is way more than any torque wrench
you will own

All you can do is get it as tight as possible with a very long
ratchet

The spec are from180 to 230 lbs on some axle nuts

Dec 13, 2012 | Nissan Altima Cars & Trucks

2 Answers

I need the torque specs for a 6 cyl 2004 Dodge Dakota 2 wheel drive- front wheel hub. In inch-lbs if possible.


Spindle nut. Tighten the nut to 185 ft. lbs. (251 Nm). Inch pounds is not an option, this critical torque spec is FT lbs.

Apr 26, 2011 | 2004 Dodge Dakota

1 Answer

TORQUE SETTING ON FRONT WHEEL BEARING NUT ON 2006 PONTIAC TORRENT


Hello, here is the torque spec for front hub bearing
Strut to Steering Knuckle Bolt and Nut
180 N·m
133 lb ft
Tie Rod Retention Nut
50 N·m
37 lb ft
Wheel Bearing/Hub Mounting Bolt
130 N·m
96 lb ft
Wheel Drive Shaft Spindle Nut
205 N·m
157 lb ft

Nov 07, 2010 | 2006 Pontiac Torrent

1 Answer

Spindle nut torque spec on a 2004 F-150


u DON'T torque this!! tighten the nut while spinng the rotor, then back off untiol it is free, then tighten it down until it seats tight, then turn another 1/8" tighter, that is it, any tighter u burn up the the wheel bearings

Feb 04, 2010 | Ford F-150 Cars & Trucks

1 Answer

Torque spec for king nut on front spindle of 1999 2 wheel drive dodge dakota?


Unsure as to what you are calling the King nut but here are the torque specs for your front end.

Steering Gear-To-Cradle Bolt...........135 ft pnds
Steering Gear-To-Crossmember Bolt (Dakota 2 WD)..........190 ft pnds
Suspension Cradle Plate To-Cradle Attaching Bolt..............123 ft pnds
Tie Rod End-To-Steering Knuckle Nut Dakota (2WD) .............65 ft pnds
Tie Rod Lock Nut.....................55 ft pnds

Dec 08, 2009 | 1999 Dodge Dakota

3 Answers

Torque on a 2000 dodge neon spindle nut the nut on the front passenger side hub


If you are looking for the spec on the large nut for the CV axle to hub it is 180 ftlbs

Oct 06, 2009 | 2000 Dodge Neon

1 Answer

Torque specs for front spindle (nut hold brake drum in place)


Tighten till the wheel bearing is tight. No one really uses a specification for that, do it by feel. when the nut is tight, and there is no play in the bearing. Should be about 15-20 ft/lbs, with about .001-.003 end play if you need exact numbers though.

May 29, 2009 | 1965 Ford Mustang

Not finding what you are looking for?
1999 Pontiac Grand Prix Logo

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8737 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...