Question about 2000 Toyota Tundra

1 Answer

Toyota Clutch Pedal Play

I just replaced the Clutch master cylinder and the slave cylinder and I can't remember if there is suppose to be any play in the pedal like clutches of old. My clutch pedal has zero play. Is that normal?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 962 Answers

Does it work ? if it is not tight to push the clutch then there should be no problem.

Posted on Oct 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1999 toyota rav4 wont go into first gear, i just repaced the clutch,clutch slave cylinder and clutch master clutch


Did you bleed the slave cylinder? Also, check pedal free play (about 1/2 inch) and pedal height (not sure on your Rav, you'll have to check with Toyota).
Only first gear, or difficulty going into all gears?

Nov 25, 2011 | 1999 Toyota RAV4

2 Answers

I'm preparing to take the transmission dowm on a 1995 rodeo and took the slave cylinder off and the boot inside is torn and has a hole. Would that affect the clutch operating? Want to check before I...


if its the outside boot only a cover to protect from dirt only way it would affect operation ,if it was leaking from seals within slave cylinder

Sep 16, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

1997 Probe Gt, 5 speed, 2.5 L V-6; 77,750 miles: replaced clutch master cylinder 11/15/2010. Clutch free play okay, pressure to push clutch pedal down- okay (these conditions apply to vehicle after...


THe problem can only really be with the clutch master cylinder. What you describe sounds like the master cylinder is not relieving pressure and this is building up in the salve cylinder, applying pressure to the pressure place and causing the clutch to slip. Can you make the problem go away even temporarily, if you open the bleed screw on the slave cylinder? You say that the free play is correct, but is the master cylinder returning fully to its released position?

Jan 26, 2011 | Ford Probe Cars & Trucks

1 Answer

My clutch pedal sits on the floor, doesnt come up on its own. I replaced both the master and slave cylinders and the bleeding process is too long. Still no response from my clutch pedal and I am super...


pull up clutch pedal, all the way up. now fill fluid to top, now open the slave cylinder, it should bleed just with gravity. let it drip for a few minutes or until you have to fill it up 2 times. Make sure that when the pedal is all the way up, that the piston is all the way back on the master cylinder. look up at the back of the master cylinder under the dashl. there is an adjustment. you want just very little play between the pedal rod and the piston, just enough that there is some play. but you need some play there. if there isnt any play, adjust the rod.

Dec 06, 2010 | 1993 Ford Probe

2 Answers

Can thr clutch on a 1992 chevy 1500 p/u be ajusted?


With a clutch cable linkage there is always adjustment in the cable length to compensate for cable stretch.

With hydraulic clutch linkage, there is less need for adjustment because there is nothing that is supposed to change.
However, the rod connecting the pedal to the clutch master is still almost always adjustable. What you try to do is optimize the pedal free play to about a half inch. You don't want to get rid of all the free play, or else the clutch master may retain pressure and cause slippage. But you don't want too much free play, or else the clutch may still grab enough to cause grinding. There is usually a locknut and threaded shaft that turns to change length.

But if the hydraulic fluid is dirty or leaking from either slave or master, rebuild them both, look for pits, put in new seals, and bleed the old fluid and air out of the line, before adjusting.

Aug 02, 2010 | 1992 Chevrolet K1500

1 Answer

1987 Nissan PU, I replaced the master and slave clutch cyls. I bleed the system and there is no air in the lines but peddle does not get hard. Could the new master or slave cyl be bad? I see you can adjust...


The shaft should come all the way back, when the pedal is back, the master shaft should be adjusted so there is very little play in the pedal. But it needs some play. Make sure you can see the slave cylinder move when you depress the clutch pedal, you will need help to operate the pedal, while you look.

May 10, 2010 | 1987 Nissan Pickup

2 Answers

Clutch needs adjusting or fluid?


they use a hydrolic system wich use fluid if your gears are not grabbing and its slipping no udjucment require because the cluck is bad but if you cant put it in gear when it on then its your hydrolic system

Sep 08, 2009 | 1992 Honda Accord

2 Answers

When i step on the clutch pedal all the way in,it gets stuck, why?.... the tranny is good!


YOUR CAR USES A HYDRAULIC CLUTCH RELEASE MECHANISM YOU NEED A NEW HYDRAULIC SLAVE CYLINDER OR MASTER, I ALWAYS RECOMMEND THAT BOTH BE REPLACED.

Jul 18, 2009 | 1991 Toyota Celica

3 Answers

Clutch


Stop driving the car now! The clutch master cylinder has an adjustable pushrod, it is set up too long now. Take it back to where it was done and tell them if they don't know how to set up clutch free play, they shouldn't have attempted the job. This may have cost you a $3500. clutch job. Get it adjusted fast.

May 05, 2009 | 1991 Porsche 944

1 Answer

Clutch problem


The rod at the end of the slave cylinder can be adjusted. make sure clutch pedal has no more than an inch and a half of free play. If free play is within the 1.5" & still have problem with clutch disengaging, chances are clutch is worn

Jan 03, 2009 | 1991 Toyota Pickup

Not finding what you are looking for?
2000 Toyota Tundra Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...