Question about 1998 Chevrolet K1500

1 Answer

Have a 98 chevy suburban. just relaced brake light switch and bulbs. i have brake lights when i push the peddle and half way through the cycle i loose them. when i let up on the peddle they come back on until i release the peddle all the way. they always go out at the same point every time.

Posted by on

  • keith_caudle Nov 13, 2010

    I already did that, and still no change.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Replace the brake light switch if no adjustment can be made . It is located near the brake pedal

Posted on Nov 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake light bulbs replaced and no light when brake applied


check the brakelight switch at the bottom of the brake peddle it could be out of adjustment, with the brake peddle released the switch should just push in a little bit and with the peddle pushed a little the switch should be away from the peddle to turn the brake lights on, hope this helps you.

Dec 15, 2016 | Cars & Trucks

1 Answer

Where is the tail light fuse?


The tail light fuse is under the rear seat on the drivers side.

Jan 17, 2016 | 2003 GMC Envoy

1 Answer

2001 Chevy lumina all lights work except the beak lights even after replacing peddle switch


To the best of my knowledge, here is how that works.
There is a "hot" wire that goes from the fuse box to the switch at the brake pedal. There is another wire that is activated when the push button is released by the brake pedal and the electricity then goes back to the brake lights.
Find a person familiar with a test meter, and see if there is current to the brake light switch. If there is, then see if the current is there (when the pedal is pushed) at the other wire. If so, go and remove a brake light bulb and see if current is coming to the rear of the car.
Be blessed.

Dec 14, 2013 | Cars & Trucks

1 Answer

None of my tail lights work. i changed the bulbs, tail light control board and fuses. I'm an electrician so i need a wire diagram of a 1996 chevy suburban


Your solution is a new combination switch,It also sounds like the hazard are activated and is non operation interfering with the brake light,but either way the solution is a combination swith

Jul 08, 2012 | 1996 Chevrolet Suburban

1 Answer

I need a wiring diagram for a 98 chevy suburban. My brake lights don't work. Checked fuse bulbs and brack light switch.


above the steering column there is a 6 way plug, it is an actual jumper harness to the brake switch it is held in place by a rosebud, pop the rosebud out and check the plug for being fully seated, I have seen many of these that have been partially pulled apart and it actually breaks the circuit/and can short it out, other than that if thats o.k. then your turn signal switch in column is defective.

Jan 14, 2012 | 2003 Chevrolet Suburban 1500

1 Answer

Why will my break lights not work on a 96 chevy suburban


Ok try this push down on the brake pedal while pushing on the hazard switch and if the brake lights come on then that means the signal switch is faulty.Replace switch.

Jan 10, 2012 | Cars & Trucks

2 Answers

Brake lights wont come on bulbs and fuses are good on 98 f150


check brake lightswitch on brake pedal if u have power to switch then replace the switch

Feb 22, 2010 | 1998 Ford F150 Regular Cab

1 Answer

98 Suburban Brake and hazard lights don't work


Check for power and ground at the two panel lights. GM uses a cheep circuit board design, they overheat and corrode on the other side of the board. not serviceable.

May 03, 2009 | 1995 Nissan Sentra

1 Answer

98 gmc suburban brake lights


One of two things cause this corroded or poor chassis earth at the bulb holders or the circuit board that holds the bulb is faulty.

Nov 19, 2008 | 1997 GMC Suburban

2 Answers

No turn signals or side brake lights on 94 chevy suburban


the problen is probably the turn signal switch with a test light check for power at brake switch if no power check for power at turn signal switch the brake lights are incorperated through the turn signal switch

Oct 18, 2008 | 1994 Chevrolet Suburban

Not finding what you are looking for?
1998 Chevrolet K1500 Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...