Question about 2004 Chevrolet Suburban

1 Answer

TURN SIGNAL BULB REPLACEMENT - 2004 Chevrolet Suburban

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 643 Answers

Unscrew bulb from back of light housing.

Posted on Nov 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My left turn signal was flashing fast. I checked bulb in back left. Turn signal good but bulb below it was out. I changed that one but turn signal still flashing fast. all other bulbs look good. ??


If the front and rear bulbs flash fast also, replace the hazard switch or you could live with it. As they are working. If one doesn't work, check grounds. I just run a new ground, much easier than cutting open the harness to find the break.

May 31, 2015 | 2012 Nissan Rogue

1 Answer

When I turn my left turn signal it flashes really fast until I press down on brake pad than it slows down and works cirrectly


This usually means that the front, or rear turn signal bulbs is bad...also some turn signal tail light bulbs are multi-purpose...same bulb lights for turn signal and brake light...You should be able to remedy this for the cost of a bulb...your owners manual and the parts counter rep can confirm the correct replacement bulb...Hope this helps.

Apr 05, 2014 | Cars & Trucks

1 Answer

Driver side brake light issue


Consider the posibility that the replacement lamp is being installed backwards. It can be done and the resulting effect on performance will be as you describe

Feb 12, 2013 | Cars & Trucks

1 Answer

Left rear turn signal on dodge ram 1500 won't work. bulb replacement didn't help.


Just had a similar question last week, and the solution was a bad socket/bulb holder.
You might try and see if there is current in the brake light wire leading to the bulb holder.
I have used a jumper wire and a safety pin to test the wire behind the socket.
I pierced the plastic insulation of the brake light wire with the point of the safety pin, and either use a tester or even a good working bulb and a good ground wire.
Be blessed.

Jan 27, 2013 | 2006 Dodge Ram 1500

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

1 Answer

I am trying to replace aleft rear turn signal bulb on a 2005 lacrosse. I removed two wing nuts but cannot remove assmbly. Is there another wing nut holding it in. I cannot find it?


3 wing nuts. here is the info needed.

gmlogoflat.gif Service Information
bhome.gifbpublication.gifbnumsrchbutton.gifbnews.gifymkbutton.giffeedback.gifbhelp.gif
2005 Buick LaCrosse ' Allure, LaCrosse VIN W Service Manual ' Body ' Lighting Systems ' Repair Instructions ' Document ID: 1537542 Tail Lamp, Turn Signal Lamp, High Mount Stop Lamp, License Lamp, Backup Lamp Replacement - Rear
1537540.gif
tif.gif
Callout
Component Name
Notice: Refer to Fastener Notice in the Preface section.
Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .
Turn Signal/Stop Lamp Assembly Replacement - Rear 1
Nut, Turn Signal/Tail Lamp (Qty: 3)
Tip
Pull back rear compartment carpet to gain access to lamp.
Tighten
2 N·m (18 lb in)
2
Lamp, Turn Signal/Tail Lamp
Tip
Twist the bulb socket and pull inward to replace the bulb.
License Lamp Replacement 3
Screws, License Lamp (Qty: 2)
Tighten
2 N·m (18 lb in)
4
Lamp, License Lamp
Tip
Twist the bulb socket and pull inward to replace the bulb.

Jul 29, 2011 | Buick LaCrosse Cars & Trucks

1 Answer

How do you change a front signal bulb on a 2004 accord


Front turn signal bulb replacement

1. Remove the inner fender
2. Disconnect the 3p connector from the front turn signal/side marker light.
3. Turn the bub socket ( 45 degree ), counterclockwise to remove the bulb.
4. Install a new bulb in the reverse order of removal.

Apr 12, 2010 | 2004 Honda Accord

1 Answer

I have a left front clearance light out how do you get it out 1


Signal and Marker Lights REMOVAL & INSTALLATION Front Turn Signal and Parking Lights
  1. Disconnect the negative battery cable.
  2. At the rear of the front bumper, turn the bulb socket 1⁄4 turn and remove the socket from the parking brake housing.
  3. Remove the bulb from the socket; if necessary, replace the bulb.
  4. If lens replacement is necessary, remove the retaining bolts and remove the lens from the bumper.
  5. To install, reverse the removal procedures. Check the turn signal/parking light operations.
Fig. 1: Common front turn signal/parking light mounting

d16c14b.jpg
Fig. 2: Twist and remove the bulb socket from the back of the turn signal/parking light lens

8b774bd.jpg
Fig. 3: If lens removal is necessary, loosen and remove the retaining bolts

09f4811.jpg

Jul 24, 2009 | 1992 GMC Sonoma

1 Answer

Turn signal


Go to your local NAPA auto parts store and get replacement tail lights circuit boards. This should solve the problem. I did for my daughters van.

Dec 08, 2008 | 2003 Pontiac Montana

1 Answer

Signal bulb replacement


you may be able to access the bulb housing under the hood. open the hood and look behind the turn signal for the bulb housing. once located, grasp the housing and turn counterclockwise about a quarter and then pull. be sure to replace wtih the same type/part number bulb.

Sep 25, 2008 | 1996 Mercury Grand Marquis

Not finding what you are looking for?
2004 Chevrolet Suburban Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...